Document text
VACON
DRIVEN BY DRIVES
X5MBTCP01 MobDBus TCP OPTION BOARD
WITH 115 VAC ENCODER INTERFACE
INSTALLATION MANUAL
DPD00112
Need Help?
This manual answers most installation and startup questions
that may arise. However, if you have any problems,
please let your first call be to us.
Vacon, Inc.
Chambersburg, PA 17202
Normal business hours:
(North America]
8:00 AM to 5:00 PM, Eastern time
+1 877-Vacon06
(+1 877-822-6606)
After-hours support is also available
vacon and Vacon, Inc. are trademarks of Vacon Plc, a member of Vacon Group.
DRIVEN BY DRIVES
All other product names are trademarks of their respective companies.
Copyright 2009, Vacon, Incorporated. All rights reserved.
X5MBTCP01 MopBUS TCP WITH 115 VAC / ENCODER INTERFACE OPTION BOARD VACON 68 3
INSTALLING THE X5MBTCP01 MoDBUS TCP OPTION BOARD
WITH 115 VAC ENCODER INTERFACE
INTRODUCTION
The X5 frequency converters can be connected to Modbus TCP using a Modbus TCP option board, the XSMBTCP01.
Every device connected to a Modbus / TCP network has two identifiers: a MAC address and an IP address. The MAC
address (formatted as xX:XX:XX:XX:XX:XX, where xx is a hexadecimal byte] is unique to the device and cannot be
changed. The Modbus / TCP board's MAC address can be found on the sticker attached to the board or by using
various network configuration tools.
In a local network, IP addresses can be defined by a user as long as all units connected to the network are given the
same network portion of the address. For more information about IP addresses, contact your Network
Administrator. Overlapping IP addresses cause conflicts between devices.
The X5MBTCP01 also provides the option of controlling the X5 AC drive from 115 VAC control signals, or of
connecting a shaft-mounted encoder to the drive to improve speed regulation. Up to five channels of 115 VAC control
are available for use in selecting direction, preset speeds, or other drive functions.
With this option, an encoder with a nominal rating of up to 2048 pulses per revolution can be connected to the X5
unit to improve speed load regulation of the drive. Overall encoder frequency at maximum process speed must be
limited to 100kHz.
This option also provides two additional control relays, each rated for 115 VAC, 1 amp, or for 230 VAC, 0.5 amp.
NOTE: This network communication interface included with the X5 option is warranted
to meet the core specifications for Modbus TCP. Many existing software applications are
custom-engineered and may contain brand-specific” communication that will not be
supported by the X5 without modification. No guarantee of compatibility with any
specific system is made. The user is responsible for any interface software and
hardware needed to make an application function.
APPLICABLE DOCUMENTS
This manual is supplied as a supplement to the X5 AC Drive User's Manual (DPD 00089, previously Form 1434).
OPTION KIT CONTENTS
The option kit includes the following materials:
Part Number Description
25100104C Modbus / TCP Option Board
INSTALLATION PROCEDURES
A WARNING
SENSITIVE EGUIPMENT
This assembly contains static-sensitive components. It should be handled only by a static-safe installer,
using a grounded wrist strap.
Failure to observe this precaution may cause premature eguipment failure.
Email: usaldvacon.com e Fax 717-264-3115
4 € VACON X5MBTCP01 MopBUS TCP WITH 115 VAC / ENCODER INTERFACE OPTION BOARD
A DANGER
HAZARDOUS VOLTAGE
* Disconnect all power before servicing a drive unit or its components. WAIT 5 MINUTES until the DC
bus capacitors discharge.
Ensure that any other power sources that may feed control logic have been disconnected.
DO NOT short across DC bus capacitors or touch unshielded components or terminal strip screw
connections with voltage present.
Install all covers before applying power or starting and stopping the drive.
The user is responsible for conforming to all applicable code requirements with respect to grounding
all equipment.
Many parts in a drive, including printed circuit boards, operate at line voltage. DO NOT TOUCH. Use
only electrically-insulated tools.
Before servicing any drive.
* Disconnect all power.
e Place a "DO NOT TURN ON’ label on the drive disconnect.
* Lock the disconnect in the open position.
Failure to observe these precautions will cause shock or burn, resulting in severe personal injury
or death.
Figure 1 shows the option board and the location of the terminals and the power supply selector.
Encoder / 115 VAC Interface
Control Relay Terminals Modbus / TCP Connector
opea LV x. no
LJ - =
sa.: 55>
S 15) 18 lel a
CM = E W
ana
me | = ES y FN WELL denas al
em p HIT P as TON
E gt 75 =
Sad et Sac] c fe i|
EI
» oe |
TIER EAT
LM S
;
2
TIST
> )
A 11)
TIN
KSL
' 08 o
s n." Veni
A irit
JEDE — 0 EE
HOHER
OTITIS
REV 4
25100067
7234730
g
enm Pha PU
Module Status LED Network Status LED
Figure 1: Option Board Layout
24-hour support 1-877-822-6606
X5MBTCP01 MopBUS TCP WITH 115 VAC / ENCODER INTERFACE OPTION BOARD VACON 8 5
Before you can install the option board, you must first remove the drive cover.
Figure 2 shows the locations of the cover screws. The torgue range for the X5 Size 1 cover is 18-26 in/lbs.
Cover screw locations
Cover screw locations
Figure 2: Cover Assembly and Screw Locations
The option board is installed just above the control board in all configurations (a Size 1 unit is shown in Figure 3 for
reference). The screws labeled “A” must be removed from the X5; those labeled “B” need only to be loosened to
accept the board slot.
" T ee
JA Te
: E
aa Ta
sä H
Figure 3: Option Mounting Locations
Once the board is in place, tighten the screws to a maximum of 26 in-lbs.
Email: usaldvacon.com e Fax 717-264-3115
6 € VACON X5MBTCP01 MopBUS TCP WITH 115 VAC / ENCODER INTERFACE OPTION BOARD
Next, install the flexible circuit to finish the interface to the control board. (Refer to Figure 4.) To install the flexible
circuit, first remove the keypad frame (necessary in this size unit). The frame is attached with two screws in opposite
corners; the screws thread into fasteners in the plastic assembly. After the flexible circuit is installed, replace these
screws, limiting the installation torque to 12 in-lbs..
Figure 4: Flexible Circuit Interface to Control Board
115 VAC INTERFACE / RELAY / ENCODER INTERFACE TERMINALS
Figure 5: 115 VAC Interface / Encoder Terminals
The XSOPTO1 option kit includes five 115 VAC inputs, two additional programmable relays, and an encoder interface.
The details of the terminals on the board related to the 115 VAC interface and the encoder are shown in Table 1 on
page 7:
24-hour support 1-877-822-6606
X5MBTCP01 MopBUS TCP WITH 115 VAC / ENCODER INTERFACE OPTION BOARD VACON e 7
Table 1: Encoder Interface Terminals
115 VAC logic input; connect input to 115 VAC to activate.
The programmable functionality of these inputs is controlled by
parameters 728, 729, 730, 731, and 732. Each of these inputs can be
disabled or configured to emulate the function of the FWD, REV, R/J, EN,
MOL, DI1, DI2, DIS, DIA, or DIS input terminals on the X5 control board.
Refer to the X5 User's Manual for more information (DPD 00089).
The neutral connection for the 115 VAC control inputs
The third auxiliary relay.
The function of this relay is set by parameter 709. Functionally, it is
capable of each of the features outlined in the X5 user manual under
parameters 705-708.
Terminal NO3 is a normally-open contact; it closes when the relay
activates. NC3 is a normally-closed contact; it opens when the relay
activates. RC3 is the common terminal associated with both contacts.
The ratings of these contacts are 115 VAC, 1 amp; and 230 VAC, 0.5 amp.
The fourth auxiliary relay.
The function of this relay is set by parameter 710. Functionally, it is
capable of each of the features outlined in the X5 user manual under
parameters 705-708.
Terminal NO4 is a normally-open contact; it closes when the relay
activates. NC4 is a normally-closed contact; it opens when the relay
activates. RC4 is the common terminal associated with both contacts.
The ratings of these contacts are 115 VAC, 1 amp; and 230 VAC, 0.5 amp.
Channel A input from the encoder. Compatible with line driver, open
collector, or totem pole outputs from an encoder. If it is an open
collector or totem pole-type, encoder outputs are used; connect the A-
terminal to Ecom.
Channel B input from the encoder. Compatible with line driver, open
collector, or totem pole outputs from an encoder. If it is an open
collector or totem pole-type, encoder outputs are used; connect the B-
terminal to Ecom.
Channel C input from the encoder, the home pulse. Compatible with line
driver, open collector, or totem pole outputs from an encoder. If it is an
open collector or totem pole-type, encoder outputs are used; connect
the C- terminal to Ecom.
Power supply terminal for use with a customer-supplied encoder. It can
be either +12 VDC or +5 VDC based on the position of the encoder
interface power supply selector shown in Figure 1. Voltage regulation:
+/- 596; maximum current available is 100 mA.
| | Eom Signal common for the encoder interface
Note that the connections described in Table 1 work only when the encoder has an internal pull-up resistor on the
open collector. Alternatively, it might be preferable to pull the + channel high, and attach the open collector to the -
channel. For example, if using Channel A, A+ on the option board would be tied to VDC, and A- would be connected
to the open collector coming from the encoder. The advantage in this method is that no pull-up/down resistors are
needed; if the encoder has an internal pull-up, this does not affect anything.
Email: usaldvacon.com e Fax 717-264-3115
8 € VACON X5MBTCP01 MopBUS TCP WITH 115 VAC / ENCODER INTERFACE OPTION BOARD
SPECIFICATIONS FOR ENCODER / 115 VAC INTERFACE
Encoder Interface 115 VAC Interface
Speed regulation < 0.1 Hz (1) |Onstate — | 90-140 VAC
Input frequency (max.) 100 kHz KE < 10 VAC
Input voltage 10-24 VDC +/- 5% Input freguency 58-62 Hz
5 VDC 500 ohms
Suggested pull-up 12 VDC | tkohms ohms On/off delay 30 ms maximum
resistor
24 VDC a 3k ohms
Terminal block wire 19-94 AWG Terminal block wire 12-24 AWG
limitations limitations
(1) PID feedback plus optimal motor turning in SLV mode employed
SETUP AND USE
The encoder interface is most effective if used in conjunction with the vector mode of operation. Refer to the X5
User's Manual (Chapter 6) for information about using the vector mode. Three additional parameters are provided
to calibrate the encoder:
PNY Encoder Pulses per Revolution 0-16383 1024
Parameter 219, Encoder Pulses per Revolution, can either be extracted from the encoder nameplate or the data
sheet supplied with it. Parameter 220, Encoder Filter Time, is used to filter the encoder signal in the event of noise.
Parameter 221 is for limiting the response of the drive, in the event of the loss of encoder signal.
Two other parameters are provided to allow more flexibility in encoder selection, and to improve PID application
usage:
Quadrature Quadrature
EncoderType or Single
Channel
Parameter 223, Encoder Type, allows the use of either quadrature or single-channel types of encoders.
Parameter 224, Encoder Range, improves PID application flexibility. This parameter should be used in situations
where the encoder feedback signal is not always directly proportional to the motor speed, for example, a winder
using an encoder mounted on an idler pulley feeding a winding spool. The PID may be attempting to maintain a
constant linear speed on the wound media, but as the diameter of the media on the spool changes, the motor turning
the spool needs to vary its speed to maintain the linear speed at the idler pulley.
When parameter 224 is set to O, it is ignored, and the PID calculates the feedback percentage based on parameter
301, Maximum Frequency. When this parameter is set to a non-zero value, the PID uses instead Parameter 224's
setting to calculate the feedback percentage.
Encoder feedback works similarly to an analog input as configured in parameters 850 (PID Configure], 851 (PID
Feedback], 852 (PID Prop Gain), 853 (PID Int Gain), and 859 (PID Derivative Gain). The "feed forward” options are
suggested for setting parameter 850. More specific details on each of the listed parameters can be found in the X5
User's Manual (DPD 00089).
24-hour support 1-877-822-6606
X5MBTCP01 MopBUS TCP WITH 115 VAC / ENCODER INTERFACE OPTION BOARD VACON 6 9
The encoder interface can easily serve as one ofthe inputs to the X5's Keeper Function (data logging). See the X5
User's Manual for more information.
Both the Vmet and Imet output from the drive can be configured to indicate the status of the encoder. Parameters
700 (Vmet) and 702 (Imet) that relate to the setup and calibration of the Vmet and Imet outputs, both have selections
related to the status of the encoder input.
The Program Sequencer function can also key off the encoder's home pulse. To make use of this function, the
encoder's home pulse (1 pulse per revolution] must be connected to the C- input of the encoder board.
TROUBLESHOOTING
Any problem with the encoder interface will result in an F37 fault. Four advanced fault codes are available to help
you determine whether you have an encoder calibration problem, or a defect. For more information on
troubleshooting, refer to the Troubleshooting chapter in the X5 User's Manual.
USING MopBus / TCP
Following are the specifications for Modbus / TCP connections:
Table 2: Modbus / TCP Connection Specifications
Transfer cable Foiled CAT5e
Default IP address 0.0.0.0
To communicate with the drive over Modbus / TCP, the drive's IP address must be set. This is done with parameters
922-925. After setting the IP address, be sure to cycle power off and back on for the new address to take effect.
LED Indications
The Modbus / TCP Option Board includes two LED status indicators: Network Status and Module Status. See Figure
1 on page 4 for the location of these LEDs on the board. Network status provides information on the network
connection status and Module status provides information on the Modbus / TCP module itself. The following tables
explain the meaning of the status LEDs:
Table 3: Network Status LED
Network Status
LED | | OFF There is no power applied to the option board.
| Red The Modbus / TCP option cannot communicate on the network.
Table 4: Module Status LED
| | OFF J | There is no power applied to the option board.
The option board is operating normally.
Module Status The option board is in Standby state or the device needs
LED Green (flashing) commissioning because of a missing, incomplete, or incorrect
configuration.
Red (flashing) The option board has detected a recoverable fault.
| | Red — | The option board has detected an unrecoverable fault.
Email: usaldvacon.com e Fax 717-264-3115
10 € VACON X5MBTCP01 MonDBUS TCP WITH 115 VAC / ENCODER INTERFACE OPTION BOARD
Getting Started
To begin communicating with the drive over Modbus / TCP, the drive's IP address must be set (use parameters 922-
925). After setting the IP address, cycle power off and on for the new address to take effect.
For information on setting parameters, see the X5 User s Manual.
Modbus / TCP is a variant of the Modbus family. It is a manufacturer-independent protocol for monitoring and
controlling automatic devices. Modbus / TCP is a client server protocol. The client makes queries to the server by
sending request messages to the server's TCP port 502. The server answers client queries with a response
message. The term "client" can refer to a master device that runs queries. Correspondingly, the term "server"
refers to a slave device that serves the master device by answering its queries. Both the request and the response
messages are composed as follows:
[8 js.
a jien SSS
O e jeee 1.
[3 [Pk
s | komeana —
6 i mee OO
7 | esirin 2.
[s Bwabhwrselngh —
Modbus / TCP vs. Modbus / RTU
Compared to the Modbus / RTU protocol, Modbus / TCP differs mostly in error checking and slave addresses. As
TCP already includes an efficient error-checking function, the Modbus / TCP protocol does not include a separate
CRC field. In addition to error checking functionality, TCP is responsible for re-sendiing packets and for splitting
long messages so that they fit the TCP frames. The slave address field of the Modbus / RTU is named as the unit
identifier field in Modbus / TCP, and it is only used when one IP address stands for several endpoints.
Modbus / TCP Option Board's Modbus Addresses
Currently, the X5 only implements Modbus holding registers (addresses 40001 - 4FFFF). The Modbus / TCP option
board supports the same register ranges and function codes that are available through the drive's serial port via
Modbus RTU. For more information, see Chapter 7 of the X5 User's Manual.
24-hour support 1-877-822-6606
X5MBTCP01 MopBUS TCP WITH 115 VAC / ENCODER INTERFACE OPTION BOARD VACON 9 11
MODBUS / TCP TROUBLESHOOTING
Following are the advanced fault codes for the drive fault (F38) related to the option board. For more information,
see the X5 User's Manual (Chapter 8]. The option board status LEDs are described on page 9 of this manual.
Table 5: Advanced Fault Codes
Advanced Possible Cause Corrective Measures
Fault Code
Check option board status LEDs,
Option board is disconnected or ribbon cable connection, and
damaged cycle power. Replace option
board if necessary.
Unstable ID during power-up Option board hardware issues PIC peret Bro pere
contact Vacon technical support.
NEM Option Board ehanged Option board was changed during If the change was intentional,
last power-down cycle power.
Option board loss
4 Invalid ID Option board hardware issues DOM oo poro
contact Vacon technical support.
Wrong or no daughter card Option DIMM module issues Cycle power. If problem persists,
installed contact Vacon technical support.
Option board software Option board software issues oe reeled N pu
contact Vacon technical support.
If the change was intentional,
Option board was removed during cycle power. Otherwise, follow
last power-down sequence corrective measures for fault
code 1.
Option board removed
Following are Modbus / TCP Exception Responses:
Table 6: Exception Responses
The function code received in the query is not an allowable
action for the slave. For example, this error would be
returned when attempting to write (preset) a read-only
register.
Illegal Data Address The data address received in the query is not a valid address
in the slave.
A value contained in the query data field is not an allowable
Illegal Data Value value for the slave register (that is, above the parameter's
maximum or below the minimum].
l An unrecoverable error occurred while the slave was
4 Slave Device Failure i l
attempting to perform the requested action.
NE E E The Modbus / TCP option board is having trouble
9 communicating with the X5 control board.
The slave cannot process the request at this time. The
master should re-transmit the message later when the
Slave Device Busy slave is available. This usually only occurs when two
masters simultaneously query a slave, or the polling rate
from the master is too fast for the slave.
Illegal Function
Email: usaldvacon.com e Fax 717-264-3115
HEAD OFFICE AND PRODUCTION:
Vaasa
Vacon Plc
Runsorintie 7
65380 Vaasa
firstname.lastname(dvacon.com
telephone: «358 (0)201 2121
fax: +358 (0)201 212 205
PRODUCTION:
Suzhou, China
Vacon Suzhou Drives Co. Ltd.
Building 11A
4281 Xinglong Street, SIP
Suchun Industrial Square
Suzhou 215126
telephone: + 86 512 62836630
fax: + 86 512 62836618
Naturno, Italy
Vacon S.R.I
Via Zone Industriale, 11
39025 Naturno
SALES COMPANIES AND REPRESENTATIVE OFFICES:
FINLAND
Helsinki
Vacon Plc
Äyritie 8
01510 Vantaa
telephone: +358 (0)201 212 600
fax: +358 (0)201 212 699
Tampere
Vacon Plc
Vehnämyllynkatu 18
33580 Tampere
telephone: «358 (0]201 2121
fax: +358 (0]201 212 750
AUSTRALIA
Vacon Pacific Pty Ltd
5/66-74, Micro Circuit
Dandenong South, VIC 3175
telephone: «61 (0)3 9238 9300
fax: +61 (0)3 92389310
AUSTRIA
Vacon AT Antriebssysteme GmbH
Aumühlweg 21
2544 Leobersdorf
telephone: +43 2256 651 66
fax: +43 2256 651 66 66
BELGIUM
Vacon Benelux NV/SA
Interleuvenlaan 62
3001 Heverlee (Leuven)
telephone: +32 (0)16 394 825
fax: +32 (0)16 394 827
BRAZIL
Vacon Brazil
Alameda Mamoré, 535
Alphaville - Barueri -SP
Tel. 455 11 4166-5707
Fax. 455 11 4166-5567
CANADA
Vacon Canada
221 Griffith Road
Stratford, Ontario N5A 6T3
telephone: +1 (519) 508-2323
fax: «1 (519) 508-2324
CHINA
Vacon Suzhou Drives Co. Ltd.
Beijing Branch
A528, Grand Pacific Garden Mansion
8A Guanghua Road
Beijing 100026
telephone: + 86 10 51280006
fax: +86 10 65813733
CZECH REPUBLIC
Vacon s.r.o.
Kodanska 1441/46
110 00 Prague 10
telephone: +420 234 063 250
fax: +420 234 063 251
FRANCE
Vacon France
ZAC du Fresne
1 Rue Jacquard - BP72
91280 Saint Pierre du Perray CDIS
telephone: +33 (0)1 69 89 60 30
fax: +33 (0)1 69 89 60 40
GERMANY
Vacon GmbH
Gladbecker Strasse 425
45329 Essen
telephone: «49 (0)201 806 700
fax: +49 (0)201 806 7099
Vacon OEM Business Center GmbH
Industriestr. 13
51709 - Marienheide
Germany
Tel. +49 02264 17-17
Fax. +49 02264 17-126
INDIA
Vacon Drives & Control Plc
Plot No 352
Kapaleeshwar Nagar
East Coast Road
Neelangarai
Chennai-600041
Tel. +91 44 244 900 24/25
ITALY
Vacon S.p.A.
Via F.lli Guerra, 35
42100 Reggio Emilia
telephone: +39 0522 276811
fax: «39 0522 276890
THE NETHERLANDS
Vacon Benelux BV
Weide 40
4206 CJ Gorinchem
telephone: +31 (0)183 642 970
fax: «31 (0)183 642 971
NORWAY
Vacon AS
Bentsrudveien 17
3080 Holmestrand
telephone: +47 330 96120
fax: +47 330 96130
ROMANIA
Vacon Romania - Reprezentanta
Cuza Voda 1
400107 Cluj Napoca
Tel. +40 364 118 981
Fax. +40 364 118 981
RUSSIA
ZAO Vacon Drives
UL. Letchika Babushkina 1,
Stroenie 3
129344 Moscow
telephone: +7 (495) 363 19 85
fax: +7 (495) 363 19 86
ZAO Vacon Drives
2ya Sovetskaya 7, office 210A
191036 St. Petersburg
telephone: +7 (812) 332 1114
fax: +7 (812) 279 9053
PRODUCTION:
Chambersburg, USA
3181 Black Gap Road
Chambersburg, PA 17202
TB Wood's (India) Pvt. Ltd.
#27, 'E Electronics City
Hosur Road
Bangalore - 560 100
India
Tel. +91-80-30280123
Fax. +91-80-30280124
SLOVAKIA
Vacon s.r.o. (Branch)
Seberiniho 1
821 03 Bratislava
Tel. +421 243 330 202
Fax. +421 243 634 389
SPAIN
Vacon Drives Iberica S.A.
Miquel Servet, 2. P.I. Bufalvent
08243 Manresa
telephone: +34 93 877 45 06
fax: +34 93 877 00 09
SWEDEN
Vacon AB
Anderstorpsvägen 16
171 54 Solna
telephone: «46 (0)8 293 055
fax: «46 (0)8 290 755
THAILAND
Vacon South East Asia
335/32 5th-õth floor
Srinakarin Road, Prawet
Bangkok 10250
Tel. +66 (0)2366 0768
UKRAINE
Vacon Drives Ukraine (Branch)
42-44 Shovkovychna Str.
Regus City Horizon Tower
Kiev 01601, Ukraine
Tel. +380 44 459 0579
Fax +380 44 490 1200
UNITED ARAB EMIRATES
Vacon Middle East and Africa
Block A, Office 4A 226
P.0.Box 54763
Dubai Airport Free Zone
Dubai
Tel. +971 (0)4 204 5200
Fax: +971 (0)4 204 5203
UNITED KINGDOM
Vacon Drives (UK) Ltd.
18, Maizefield
Hinckley Fields Industrial Estate
Hinckley
LE10 1YF Leicestershire
telephone: +44 (0)1455 611 515
fax: +44 (0)1455 611 517
UNITED STATES
Vacon, Inc.
3181, Black Gap Road
Chambersburg, PA 17202
telephone: «1 (877) 822-6606
fax: «1 (717) 267-0140
j D p D a a 1 7 A T