Document text
ALAN: © brecht Albrecht
Tectalk
SERVICE MANUAL
2-WAY PORTABLE
HANDHELD
PMR 446 RADIO
Nov. 07. 2001
ALAN Electronics GmbH
СОМТЕМТ
1. GENERAL
1.1 General
12 Characteristic
1.3 Composition
2. SPECIFICATION
2.1 General Specification
2.2 Electrical Specification
3. OPERATION
3.1 Key Name
3.2 ICONS оп LCD
3.3 Key Functions
3.4 Setting and Operation
4. ADJUSTMENT
4.1 Frequency synthesizer
4.2 Transmitter
4.3 Transmitter Test
4.4 Receiver
4.5 Receiver Test
4.6 Symptoms, check point & Correction
5. DESCRIPTION OF RADIO CIRCUIT
5.1 Frequency Synthesizer
5.2 Receiver
5.3 Transmitter
6. BLOCK DIAGRAM
7. SCHEMATIC
8. COMPONENT PARTLIST
9. ASSEMBLY DRAWING AND PHOTOGRAPH
10. CHANNEL DATA (With Sub-channel data)
1. ОЕМЕВА
1.1 GENERAL
This equipment, ТесігіК is called 2 мау portable handheld radios.
The frequency range is 446.00625 to 446.09375МН2, UHF operating channels for
Europe-wide used 2 way portable radios according to PMR-446 Standard.
1.2 CHARACTERISTIC
a) All active device in this radio is composed of semiconductor and high
density IC.
b) To design this radio in compact and weight approximately 140g including
battery.
C) CPU of this equipment is HD4048812B from HITACHI.
d) It's power can operate by use of alcaline 4 cell (1.5V AAA) battery.
1.3 COMPOSITION
This radio is composed of following.
a) Transmitter (W/Antenna)
b) Belt clip
2. SPECIFICATION
2.1 GENERAL SPECIFICATIONS
a) Frequency Range : 446.00625 to 446.09375 MHz
b) Output Impedance : 50 Ohms Unbalanced
c) Modulation Type : 8K50F3E
d) Communication Mode : Simplex
e) Channel Capacity : 8 channel
f) Channel spacing : 12.5 KHz
g) Power : 6.0V(ALCA 1.5V x 4AAA)
h) Battery Life : ALCA.1000mAh > about 35hours
NI-MH 600mAh > about 22hours
(TX 5% ,RX 5% ‚Standby 90%)
i) Operating Temperature : -20°C to +55 °C
j) Dimension : 95.5(H)x 50(W)x 26(D)mm
k) Weight : 120g(with Battery)
2.2 ELECTRICAL SPECIFICATION
a) TRANSMITTER
1) Output power : Max. 0.5W
2) Frequency Stability : +/- 5PPM (-20°C to+55 °С)
) Modulation Method : FM
) Oscillation Method : PLL SYNTHESIZER
)
3
4
5) Max. Frequency Modulation : < +/- 2.5 KHz (with tone)
6) Cooling Method : air-cooling Method
7) Spurious Emission TX : < -36dBm
8) FM Hum/Noise : > 40dB(1kHz 60% modulation)
9) Distortion : < 5% (1kHz 60% modulation)
10) Tx Audio Response : 6dB /OCT +/- ЗАВ PRE-EMPHASIS(300Hz to 2.5kHz)
b) RECEIVER
1) Receive Method : Double Super Heterodyne
2) Receive Sensitivity : -118dBm up (20dB SINAD W/CCITT)
3) Squelch Sensitivity : -120 to -130dBm (Audio on/off point)
4) Bandwidth : > 8.5KHz
5) Adjacent channel rejection : > 55dB
6) Local Frequency Stability : +/- 5PPM (-20°C to +55°C)
7) Spurious Response Rejection : > 65dB
8) Audio output : 200mW(8 Ohms load THD 10%)
9) Distortion : < 5% (1KHZ 60% Modulation)
10) RX Audio Response : 6dB/OCT +/- 10dB DE-EMPHASIS(300Hz to 2.5kHz)
11) S/N Ratio : > 40dB(1kHz 60% modulation)
12) IF: 1'st IF = 21.7MHz
2'nd IF = 450kHz
13) Local Frequency : 1st Local Frequency = fc -21.7 MHz
2nd Local Frequency = 21.25MHz
3. OPERATION
3.1 Dravving of the radio
<=, mb «ші mi
WO NJ CO
FUNCTIONS AND CONTROLS
1) Battery Door 11) Down Button & Volume Control
2) Monitor Button 12) Function Button
3) Detachable Belt Clip 13) Power On/Off & Enter Button
4) Push-To-Talk (PTT) Button
5) Antenna
6) External Mic / Speaker
7) Built-in Speaker
8) LCD Panel
9) Built-in Microphone
0)
10) Up Button & Volume Control
3.2 ICONS оп Ср
OWO O ша а 2 т
£ CU C D G |
Ж
7
Е
free,
7
ka.
~
LY
R
=
R
L
Kd
GEEN
E
—
mma,
u
Ven
L.
=.
L
e
==.
Ы
LJ U U.
1) RSSI (Receiving Signal Strength Indicator) or TX Bar Icon
Indicates the receiving signal strength during transmission and it can ШІ
be indicated the number of bar according to the strength of receiving
signal. It (TX Bar) is not transformed.
2) Monitor Indicator
Appears when the monitor button is used.
3) CTCSS Indicator
Blinks when the correct CTCSS tone is entered.
4) Auto Channel Scan Indicator
Appears in the auto scan mode or when the auto scan mode is
activated.
5) Dual Watch Scan Indicator
Appears in dual watch scan mode or when the dual watch scan mode
is activated.
6) Key Lock Indicator
Blinks in auto lock selection mode or when the key lock is
activated.
7) VOX Indicator
Blinks in VOX selection mode or appears when УОХ is activated.
= ph SA
8) Battery Level Indicator
Battery Level Meter indicates the remaining battery strength.
Blinking when the Battery charge strength is Low-cell only and then red
LED Blinking at every 5sec.
When the TOT Penalty is Warning Beeping at initial activation and not
Transmit at 10sec.
9) Tx Indicator
Appears when a signal is being transmitted.
N
10) Вх Indicator
Appears when а signal is being received.
11) Large Segment Display
Indicates the channel number in use at the normal mode. wm 1 1
When the Function Button is pressed, it Displays the function menu me w w
in sequence : ) | | { j І,
СН / ctc / SC / dW / VO / Ма / АГ о / CAL / TON / tAL / БЕР
12) Small Segment Display
Displays the CTCSS tone option at the normal mode. LU LU LU Ж
CTCSS option is displayed іп Hz. LA LI LI, LI
Displays the SUBMENU of each MENU in the function mode.
(e.g. CH 1 їо 8 / ctc: 1 to 38, OFF / SC: up, dn, OFF / dW: 1 to 8, OFF /
VO: High, Mid, Low, OFF / Vdt: 5sec, 3sec, 2sec, 1sec / Alo: OFF, Auto /
CAL number: 1 to 7, OFF / tON: no, Freq / tAL: On,OFF / bEP: On,OFF)
3.3 Key Function
3.3-1 ENTER BUTTON (#13)
1) Short Touch - Power On
- Press this button (#13) briefly to turn the unit on.
A short confirming melody will play.
2) Long Touch - Power Off
Press this button (#13) for longer than 1.5 seconds to turn the
unit off.
Press it to confirm the required option for respective functions
during function edit mode.
3.3-2 FUNCTION BUTTON (#12)
1) Short Touch
- Press this button briefly to enter function edit mode in standby
mode.
2) Long Touch
- Press for longer than 1.5 seconds to activate the KEY LOCK in the
standby mode.
Please note all buttons will be disabled except the Monitor
Button (#2) and PTT Button (#4) will remain fully operational.
3.3-3 UP BUTTON (#10)
1) Short Touch
- Inthe standby mode, press this button briefly to move to the next higher
main volume level.
In the function edit mode, press briefly to shift Нот the current option
in each submenu to the next option in the same submenu.
2) Long Touch
- Pressing this button for more than 1.5 seconds will allow you to navigate
at a more rapid rate through different volume level in the standby mode or
through different menus in the function edit mode.
mode.
3.3-4 DOWN BUTTON (#11)
1) Short Touch
- Inthe standby mode, press this button briefly to move to the previous
lower main volume level.
In the function edit mode, press briefly to shift from the current option
in each submenu to the previous option in the same submenu.
2) Long Touch
- Pressing this button for more than 1.5 seconds will allow you to navigate
at a more rapid rate through different volume level in the standby mode or
through different menus in the function edit mode.
3.3-5 PUSH-TO-TALK (PTT) BUTTON (#4)
- Press it firmly and speak into the Built-in Microphone (#9) to transmit.
The red Tx LED Indicator at the right side of the LCD Panel (#8) will
light.
- Release it to revert to standby mode. When an incoming call is received,
the green Rx LED Indicator on the left side of the LCD Panel(#8) will light.
- 2-Way Call Ringer:
Press the PTT Button twice quickly to call another party on the same
channel. The word CALL and the Tx icon will appear in the display.
The user selected call ringer melody will play.
3.3-6 МОМТОВ ВОТТОМ (#2)
- Press it to check activity on the current channel before you try to
transmit.
- Adjust the Volume Control (#10, #11) if necessary.
- When you press the Monitor Button, the LCD Panel (#8) will be illuminated
with an amber color back-light and both the Tx and Rx LED indicators will
light.
- М can be activated by pressing Monitor ‚up/down ‚enter and function key.
- lf you press the Monitor Button during the function edit mode, you will
return to standby mode directly.
- To setup Auto Monitoring ‚press Monitor key for three seconds.
3.3-7 EXTERNAL MIC/SPEAKER (#6)
- This jack accepts an optional headset/microphone for totally handsfree
operation.
Please refer to the enclosed Accessory Order Form to order accessories.
See also section regarding VOX SELECTION MODE.
3.4 Setting and Operation
3.4-1 BASIC CHANNEL SELECTION
In order to communicate with other sets,both you and the receiving party
Must be on the same channel.
The set has 8channels (1-8) as indicated by the large digits in the LCD
Display Panel (#8). Before, trying to transmit on the selected channel,you
should press the Monitor Button (#2) to check the activity on that channel.
If someone is already on the selected channel, you should try another channel
that is clear.
To change the basic channel,
- Inthe standby mode, press the Up Button (#10) briefly to move to
the next higher main channel number.
- Press the Down Button (#11) briefly to move to the next lower
main channel number.
3.4-2 CTCSS (Coded Tone Controlled Squelch System) SUB-CHANNEL
SELECTION MODE
This feature allows you to utilize a less used channel range (01-38) within
а тат channel. This enables you to communicate with another party on the
same тат channel using the same subcode.This helps to avoid congestion on
the main channel and filters out unwanted noise and static.
There are 38 CTCSS subchannels for each main channel.
To change the CTCSS subchannel,
- Press the Function Button (#12) until the word cTc appears in the LCD
Panel (#8).
- Press the Up Button (#10) or the Down Button (#11) to choose the desired
subchannel to use. The corresponding subcode frequency will be displayed
in the lower right corner.
- Press the Enter Button (#13) to confirm your selection.
NOTE: To communicate with other PMR units, they must be switched to the same
channel and CTCSS subcode.
To communicate with other PMR units that do not have subcodes,
switch your unit to the same channel with the subcode set to OFF.
3.4-3 AUTO CHANNEL SCAN MODE
This feature allows you to scan for an active channel and communicate with
the party transmitting.
To access the Auto Channel Scan menu,
- Press the Function Button (#12) until the auto channel icon blinks
and SC appears in the LCD Panel (#8).
- Press the Up Button (#10) or the Down Button (#11) to choose scanning up or
down from the current channel number.
- Press the Enter Button(#13) to confirm your selection.
- The unit will begin scanning for an active main channel. It is able to
transmit by scan start channel during scanning.
- When the scan release , the unit will be standby in scan start channel during
Scanning.
- Press briefly the Monitor Button , It allows you to skip over current channel
on the scan list. On the other hand press long the Monitor Button , It allows
you to delete current channel on the scan list.
- To turn off the auto channel scan feature in the standby mode, simply press
the Function Button(#12) once.
3.4-4 DUAL WATCH SCAN MODE
This feature allows you to monitor two different channels at the same time.
If you pre-set any priority channel other than the current channel in use, the pre-set
channel will be scanned every 0.5 second and signals you when a call is received.
To access the Dual Watch Scan menu,
- Press the Function Button (#12) until the dual watch icon blinks and dW
appears in the LCD Panel (#8).
- Press the Up Button (#10) or the Down Button (#11) to select the desired
channel number you wish to closely monitor.
- Press the Enter Button (#13) to confirm your selection.
- To turn off the dual watch feature in the standby mode, simply press the
Function Button (#12) once.
3.4-5 VOX SELECTION MODE
The Voice Activated Transmission (VOX) function allows your voice to activate
transmission automatically when the Communicator is used with the optional
handsfree mic/headset (refer to enclosed Accessory Order Form). It also allows
handsfree use when a mic/headset is not being used without having to use the PTT
Button (#4).
To access the VOX Selection menu,
- Press the Function Button (#12) until the VOX icon blinks and VOX appears in the
LCD Panel (#8).
- Press the Up Button (#10) or the Down Button (#11) to select from high,mid,
low or off. High, mid or low setting determines VOX response sensitivity.
- Press the Enter Button (#13) to confirm your selection.
- To turn off the VOX feature, enter the VOX selection mode and then select
Off.
3.4-6 VOX RECOVERY TIME SELECTION MODE
This allows the response characteristics of the VOX function to be precisely
adjusted to suit individual needs.
To access the VOX Recovery Time Selection menu,
- Press the Function Button (#12) until Vdt appears in the LCD Panel (#8) with
the VOX icon blinking.
- Press the Up Button (#10) or the Down Button (#11) to select from 5,3,2,or
1 second setting. This setting determines the delay time between transmitt
-ing and receiving.
- Press the Enter Button (#13) to confirm your selection.
- Please note you may need to try different VOX time settings to determine
the best value to suit your speaking habit.
- To turn off the VOX feature, enter the VOX selection mode and then select
Off.
3.4-7 AUTO KEY LOCK SELECTION MODE
This feature prevents accidental channel change and disturbance to the preferred
Settings of the Communicator. Auto Key Lock temporarily disables the UP,DOWN
And Enter Buttons.
To access the Auto Key Lock Selection menu,
- Press the Function Button (#12) until the auto lock icon blinks and Alo
appears in the LCD panel (#8).
Press the Up Button (#10) or Down Button (#11) to select the Auto option.
Press the ENTER key to confirm your selection.
If you do not press any key for more than 15 seconds in the standby mode,
all respective keys vvill automatically be locked.
To turn the auto key lock on or off in standby mode, simply press and hold
the Function Button (#12) for more than 1.5 seconds.
To quickly activate the Auto Key Lock, hold the Function Button (#12) for
more than 1.5 seconds.
3.4-8 CALL RINGER MELODY SELECTION MODE
This feature provides 7 user selectable call ringer melodies to alert you ofa
calling party.
To select your favorite Call Ringer melody,
Press the Function Button (#12) until the call icon blinks and CAL appears
in the LCD panel (#8).
Press the Up Button (#10) or Dovvn Button (#11) to previevv the 7 available
melodies.
Press the ENTER key to confirm your selection.
By using PTT key, the mode vvill be changed from calling to transmit mode,
stopping current calling.
If you set this function to call off, call function is disabled in this
Mode.
3.4-9 TONE DISPLAY SELECTION MODE
This feature allovvs you to select the preferred display format for the СТС55
code setting.
If frequency “FrEq” was chosen, then the display in the CTCSS will be shown
as frequency. However, if the number "no." was chosen,then the code number
will be displayed in CTCSS function.
Press Function Button (#12) until ЧОМ" appears in the large display.
Press Up(#10) or Down(#11) to change the format.
Press Enter(#13) to confirm your selection.
Otherwise, the displayed state is automatically accepted if no
key is pressed after 5 Seconds.
3.4-10 SQUELCH TAIL SELECTION MODE
This feature allows you to set option mode of squelch tail
elimination.
Press Function Button (#12) at the CTCSS display option mode,you can
select On or Off with Up(#10) or Down(#11) button.
When you press Enter Button (#13) or not press any key in 5seconds, it
returns back Stand-by mode with back beep sound after installation squelch
tail elimination option its setting.
Transmit Roger tone 400ms after PTT release.
3.4-11 ВЕЕР TONE SELECTION MODE
This feature allows you to program beeping or not beeping with key selection.
To set key beep mode, press the function key at the squelch tail ON (OFF mode
at the same time operate beeping according to the tone of key beep.
- You can select On or Off with Up or Down key.
- When you press Enter button (#13) or no press any key in 5seconds.
it returns back Stand-by mode vvith back beep sound after
installation key beep option its setting.
- To turn on the button beeps features, select Beep On.
- To turn off the button beeps features, if you vvant quiet radio
operation select Beep Ой.
4. ADJUSTMENT
4.1 Frequency synthesizer (PLL)
a) After connecting the power meter and dummy load ( to internal 50 Ohms connection
point), join the antenna connection cable vvith above equipment.
р) Check the voltage between ТР & GND in digital voltmeter.
c) Then set the low channel of set the lowest frequency.
c) After pressed PTT key of set, trim VC1 for adjusting the lowest frequency
Frequency of TX channel to DC 1.5V in the voltage of TP1.
d) After releasing the PTT key, And then check if the highest frequency of
Rx channel is within DC 0.6 ~ 2.3V in the voltage of TP.
4.2 TRANSMITTER
a) Connect EUT & measure equipment according to block diagram below.
POWER SUPPLY MODULATION METER
OSCILLOSCOPE
POWER METER DUMMY LOAD
DISTORTION METER
SPECTRUM-ANALYZER
AF OSCILLATOR FREQUENCY COUNTER
р) Connect DC 6.0V, voltage preset to EUT.
с) Connect "power meter" & "dummy load (50 Ohms)".
d) Adjust Tx frequency according to trimming trimmer VC2.
e) Connect AF oscillator to mic terminal for conform modulation degree.
f) Adjust the frequency of AF oscillator to 1КН2 and adjust AF level
should be 60mV.
g) Checking oscilloscope and modulation meter. max.
frequency deviation should be in +/ -2.5 KHz.
4.3 TRANSMITTER TEST
a) Output Power Test
Power(6.0V DC) should be Max.500mW.
b) Audio Response
Connect AF oscillator to Mic terminal and then firm the audio level
that doesn't distortion the wave of oscilloscope in the frequency
range, 300Hz to 3kHz. Check the audio level for 300Hz to 3kHz based on
frequency standard, 1kHz.
c) Modulation Degree Test
1) Connect AF oscillator to the MIC terminal and then adjust the level to
To 60mV
2) Measure the oscilloscope wave and he point needle of modulation meter
After pressing PTT key.
3) Sweep gradually the frequency of AF oscilloscope from 300Hz to 3KHz.
3kHz.
4) At this time, the point needle of modulation meter should be in
+/- 2.5 KHz.
d) Spectrum Test
1) Antenna is 50 Ohms and attenuator degree should be 20dB more.
2) observe the spectrum with pressing PTT key.
The harmonics should be less -36dBm than carrier.
4.4 RECEIVER
a) Preparation
1) Adjust the power supply to DC 6.0V
2) Adjust Voltage level to 0.7Vrms (8 Ohms load) after power on.
b) Connection method
8 OHMS LOAD
OSCILLOSCOPE
DISTORTION METER
SINAD METER
POWER SUPPLY
С) Conform of Rx sensitivity
1) Adjust SSG to channel frequency.
2) Adjust modulation frequency, 1kHz to modulation degree, 1.5КН2.
4) After adjusting the frequency of SSG to channel frequency, RF level sets
to -47dBm.
d) Conform of Squelch sensitivity
1) Set the standard channel.
2) In squelch mode, SQ volume RV1 must be turned counterclockwise.
3) After adjusting SSG to channel frequency, the adjusting SSG to level.
-120dBm set is audio on, -130dBm set is audio off.
4.5 RECEIVER TEST
a) Rx sensitivity test(field strength)
SSG should be adjusted to 20dB of SINAD's point need seeing wave of
oscilloscope as SSG sets іп 1kHz with 1.5KHz frequency deviation.
At this time, normal RF level is < -118dBm.
b) Audio Distortion Test
1) SSG should be adjusted like way of point a) and RF level sets to —47аВт.
2) Adjust to 0.7Vrms(8 Ohms load) seeing Audio wave.
3) Read the needle of distortion meter(normal condition would be less than
5% distortion.)
c) Squelch Test
After RF level of SSG should be set to the least level, RF level should be
gradually increased until speaker makes audio sound.
At this point, check RF level(Check Audio on : -120dBm, Audio off : -130dBm)
4.6 Symptoms, Check point & Correction
a) Diagnosis method
1) Check each switch to work well.
2) Check voltage of battery.
3) Problem develops from transmitter or receiver?
b) Troubleshooting
1) Transmitter
-Power key is on condition but does not work.
Battery could completely discharge.
Battery cell twist..
Touch problem come between Battery and Radio.
- Fail to transmit
Run out of battery or charge problem.
Fault of PTT key.
Fault of Q4, Q5.
- Transmitter works but frequency is unmatched
Out of order in frequency synthesizer.
Out of order in X-tal(X2).
- Audio does not sound(Tx power and Tx frequency are normal)
Problem of microphone or Mic connector.
IC U7 problem.
- Tx is set when switch is on.
Tx switch problem
2) RECEIVER
- Rx does not work
Speaker line open problem or connector problem.
Receiver power circuit problem.
Audio amplifier Base band IC U4 problem.
- Only noise sound
U12 problem.
VCO problem.
- Rx sensitivity is weak
Antenna mounting problem.
Front-End circuit problem.
Local oscillation frequency deviation.
SF1 saw filter fail.
VCO problem.
- Squelch does not work
U12 problem.
Control logic problem.
5. DESCRIPTION OF RADIO CIRCUIT
5.1 Frequency synthesizer
Frequency synthesizer consists of VCO, PLL IC(built in PRESCALER) and loop
filter.
a) VCO
VCO is composed of ONE VCO. Oscillation circuit takes colpitts circuit using
variable Diode. And VCO is composed of D1, Q8, Q9,C81,C75,VC1,L1,C74,C76.
VCO control voltage through loop filter adjusts frequency and Microphone
signal through Modulation terminal makes modulation.
b) PLL IC
PLL IC is adjustable IC to produce the wished frequency which VCO provides
through loop filter.
It has internal counter using 21.25MHz reference frequency to make 6.25KHz
as reference Signal.
VCO frequency from prescaled input is divided signal is compared with Refer-
ence signal phase in phase comparator.
Built-in charger pump changes voltage (until two signals are in phase) and
charged voltage supplies VCO through loop filter to produce the desired
frequency.
Frequency data associated with channel goes to PLL IC by CPU through CLOCK,
DATA. PLL IC enables by strobe line of CPU.
C) Loop Filter
Loop filter is composed of R48,R49,C84,C85 and changes pulse from pin14 to
DC. and eliminates harmonic component in pulse.
It helps VCO oscillate clearly as DC voltage is supplied into varicap.
5.2 RECEIVER
This is composed of Dual Conversion Super Heterodyne. First IF is 21.7MHz.
Local oscillator frequency is lower in 1'st IF than Rx frequency. It is
called low side injection. Second IF is 450kHz. 2™ local oscillator frequ-
ency comes to 21.25MHz.
a) Rx/Tx Conversion Circuit
Rx signal goes to Rx/Tx conversion circuit through FIXED antenna connector,
low pass filter(L5,L6,L7,L18,C42,C43,C45,C46,C47) and receiver resonance
circuit composed of L8,C1. When transmitting,voltage through R25,L12,D6
supplies,D7 of receive input is short and Tx is on condition. When PIN diode
off in condition of Rx,L8 and C1 resonate serially and make impedance match-
ing at receiver bandpass filter. (SF1).
b) Front End
Front-End has Q1 to provide a high sensitivity and low noise feature.
It employs Saw filter as band pass filter to eliminate image frequency and
to produce enough pass band by Q1 input and output.
C) Mixer
Mixer has one base BFQ 67W(Q2) to feature high low noise quality.
It has RF signal through L7, L8, SF1,SF2 and Q1 RF signal from Local oscill-
ator mixed.
It develops 1'st IF ,21.7MHz. 1st IF goes to 1st IF amplifier Q3(KTC4080)
base through X-tal filter XF1.
IF of mixing signals is selected and taken into X-tal filter.
Output impedance of mixer is direct matched with input impedance of X-tal
filter.
Matching of filter satisfies pass bandwidth of filter, ripple elimination
with in pass band, and attenuation characteristic of stop band.
X-tal filter is composed of two pole monolithic X-tal filter,
8kHz of IF bandwidth R11 is used as impedance matching with 1'st IF Amp ОЗ.
d) IF AMP and Detection
1'st IF AMP ОЗ supplies IF(U12) mixer input pin16 through output resistor
R13 and C21 to need gain in insertion loss of X-tal filter and last stage
circuit. Multi-use IF IC makes up of mixer IF АМР. Pin1 2" local frequency
frequency enter to pin 1.
It supplies mixer of internal IC. Mixer output of IC through pin3 passes
450kHz ceramic filter, supplies 2"? IF amplifier and limits.
After 274 IF AMP has а process of enough gain and AM rejection, it comes to
quadrature detection. Demodulated audio signal by T1(Quad Coil) is amplified
and comes out to ping.
Detected audio signal through R22, УВІ and input in audio amp.IC U4 through
C22.
e) Squelch Circuit
Noise component of detected outputs has amplification squelch threshold is
controlled by Resistor R18,C31,R15.
f) Audio Amplifier
Demodulated audio signal enters to pin2 of U4. After above signal amplies in
U4 pind through C220. It comes out to pind Then, It reaches at speaker.
5.3 Transmitter
When Tx develops with pressing PTT switch, VCO output amplifies through Q4,
Q5 transmits by antenna through low pass filter.
Tx RF signal produced from Tx VCO is amplified by DRIVER Q5 through C53 and
entered Q4 POWER TR input terminal with final amplification.
After this stage, the signal is emitted at antenna through 50 Ohms matching
circuit to low pass filter (L5,L6,L7,L18,C42,C43,C44,C45,C46,C47) to elimin-
ate harmonic.
5.3-1 Audio Modulation and Audio Amplification
Audio signal produced by external or internal microphone,limits amplification
by IC U7.. It enters to VCO through low pass filter and U2.
Max. Frequency modulation deviation is adjusted by VR1 keeps noise and audio
from entering to VCO at time of TX.
Audio modulation and Audio Amplification has characteristic of 6dB/OCT pre-
emphasis by U7(NJM324V).
6. BLOCK DIAGRAM
CON
| ВО
г BOR
АМТЕММА
| RX/TX SH
L.P.F
| і 06,7 ы ГА
Lep1
BAT L60-Jsh ват
БОО вел
-+
vës Full Че 6m 0 |
Y ye
"2888 8888: TA
5 * RRV B “|
di 84321
LPF2 Y
025
KRA306 „уту
1 БІРІ
ФОР FILTER
Y FRONT END AMP
L L
926 Е Е + vco 08,9 4
р KRAZ06 pyrX 5 5
2 1
PHR/ENT
ЩожЕ TEST MoD |e orEsr E SEL Y
|| зі optioni
| G 21.25M Е
з la option2
ТЕМ Ех ом Ех усс аы E
FTIZON options x= L
пх ом E
935 CPU
тхусс optiona
0506 C EL EF
Рив ом U 1
ш.
4 Low CELL ша PLL SYN. 2ND LOCAL š
= CEL
= BUSY MIXER
= +11 le ist IF FILTER
Bri
аз IF IC
për |
[] 450K ый
ЕМ LL EN
VLEVELL A
рата
VLEVEL2 T
kes 4
R21 | R19
sa LEVEL
ТОМЕ EN-COD
RM
ONE QUT
PRE-EMPHA Т
MIC H e
Сы озна ik
L LIMITER £ ы
й М
MESE]
A] ah Т
AT-JY2506-050-1
ЖЕ LPF
= 300Hz F
SPEAKER
ELECT VOLUME
AUDIO PHR AMP HPF
- НЕ-----ғІ|/чон Í<
J-COM. CO.,LTD.
BLOCK DIAGRAM =
IORA Hia Number
в
E
Bat
November Б, 200i Bheet
oF
RX LED
SM-2333T =;
IX LED 021 RED D22 GEN KRAZO6.
du smi cesar zeer E ee Brady R27
R101 vee Et D + 4—oeat
330 қар R105 R106 R107 R108 | E p З eo EN Ax x
hil (DOG [218 J A nd 624 + +
өзі өзг tt раң KRR306
KRC404 KRC404 ma sui + A. + RED
" ) 8888 бы I TT I I = т
5 чт» = L2 R55
R47 cot cao 101 kes
L [ ši on T T E Жа ші 5 me ER
C= ү = ПЕ. = = = = = сєз 02 Ks? А SS >
E E Ir Kë > се? 4 = [104 NE
b b t | 5 T | 2 n Yu | R26» HË eu
T T Em E I xi Š |
230 ә: Fese 183 E = A рі '
Ë Leu KRËSO4 5 us 102 es _ =
BE BEKEKZEKEKEKEEEEEBGEBE M-PLT zor ji dsns “Че sg [02 = ma бес >Rao Юн! 2
ЕБ Y ҰҰҰ 50665555565 5 ss zi Z RAL 22 зі Yor HOH kez 283 9^5 KDS160 сав
КТ 8BYSYSESSSËË 3322382333 T l ш шк 1330 Tso = +
H 1 1858972105876543521 C162 R156 10K: P's XXX Qa 14 [ zan
R103 vec o—H avcc 520 [60 103 1M R112 ші рі R34 ғ) сез 0270n 10Р
330K kos | ш 16 ЗУ 125372 885! Tat Б
ват он BT 2) ag э ET 10K [220 | 2] FIL fiz Që == ы КЕ pet 10K EX
349 і 3 c Усс ha 1n ШОР | sok ов 5 enz
КЕ 3a sis [58 EIC Ha sio ora ШЕ e > os | Бғабы E B.
стз -31625
RSSI 4 д2 сі? FZ i qël PAQE 2702 H | : | (ке — ress
= BUSY HS) — DATA хо TEJ ы. = ==
өз 516 BS 8 ste eo В A" ста| ar spo сев las
vec o—BUSY L6 ag sis [SS TETIZOZFN Es azonjeze T dez ti = бы
TploIST-Hop 7| ps m" Eén ex оваз [2Р2
HON. ©за тес) ра |487 pa RIT
A-GND m sis 63 Ll (2207 ххх | қоза | вза Те 220
=== ч
|52 RASA 7 pj
TESH HD40488-12828TECV4 ) 8537512 eze |532 *H + 二 =
osci RS2/511 Bi ALT SN2 { БЕРІ) š E
a KQT901 laes Т +376T3 R420 R46 Ств 2 R45 сті
osc2 851/510 il se ab х2 АГ; XXX Of [2202 бак? iP
las Do = с = 21.25MHz = ЭЕ >
GND Rso/se9 S2 —gj 4
v мале s£ S ix ар =
к? я
х2 a7 _v-PIT MICI esë ЕЕ 264 R46
келт с1ав CMP4S40 4Р_|33Р | 1668 ххх ххх ter сте за de
RESET raise 486 PTT } 4 == = Ххх 220P з SU = Le
= = = ктсаово I ean
vee Raovss 48 HON 164 ж ік or
kee hag de + 1 сі?
po R33/54 — SË 10207 i 16 St RIZ Lio ЭРХ ( ЕН
as pat STËRO = = 4 Й
|42 CLK XX
vz 831/52 Е с220 = 2 із вав 34 вы УВЕ +H
оз взо/51 |8 тв E zë 4 к ва diis KDS114
|+ 3| 14 R24 [cis
DORRRRRRRRRRRR віз ак?
орррррі їі б 7 10K SP
3829589118183: 1118111 i | ШЕ 2% S. pa
us 2 Е Ë E FE EE ERBE C140 * R29 = 05160
з la FEEREEPEBEREEREEREBL я RH CFL 100K 27
GND Do 上 m =
e pl -Е 108 к, jorasous | „ liz- ЖО kra xri
6 3 a N 7 36-16BB-08 + МҒ21.7М3 Kis 19
ORG DI M R20
ciii 2 > da 4 `". УСО EN TXON R143 2 css PME, c28 R3 202° „en ік
2| Jnc sk Р) RXON 100K 104 \ в m jt tT
joa) 5, Қ H E LLL LL RT T 7 I R14 330
vec vee cs прати = 30тих2 WIRE сза ris | 104 тео
акезсавау чі OT TT TAB C * 104% 7) 470K C23
БЕБЕК NCT (Ны ) c29 о io2
PHREN |/ сазо T 102 7 Ti Tiz el En KD5226 =
R122 VRI Kaos | t RA 1 KA
4 R17
EE, вия i cize 100K AAA 小 x "m SX 0 [+
7 і Maze c128 +
piss) Әк | NEE R127 102 Haar саз В 82% RIS 4 25
SHË Ë xL 100к 10K
82K | свт Ri21 Генс) тіге | 10% eue IE in sek E zo
11907 2 ЕТИК LC roc + } esp "ГУ Ë л K last 1%
| YT Rizal ы Ток RIN 103 + чм vec Kss Fio [25 (ак? =
223 ONS се Rage 4 Б м ad er =
102 10 X esp от > = = с
vt: R129 сіб NJATE = li
(ез2: || = Sal 104 ч
Д K. 2 10K =p €103)
104 | мамзачу LL 4 ват gjë сөзі 22/41
ECE san Klazoıs L
Т зі "10K
Fizz “Ен clo 引
u ОР
a23 ar RT Бо” 22
KRC404 ^ x M vec
= R141
> ui ак?
сізг | ci25 us |
veegt ) in vee jE—ovcc „pls Na
3x0 vee C176
100к | 975 104 2 carn ours 7 2 XIN мо $ i$. "^ pë
- i-o E
тароо
E Al смо orav 8 TETE SL Tabor Hë
KRC404 NOME IRON кароо
= “isa = ore Я кс RAMPO Hš
02 С 153 [163 чо ВІС RAMPI HÍ |
= hos. 208 er Sep вна
LOS 2 Fiza
adf mem ы: Re en
Fm 104
025 ват — = 33k
й nar.
- 5
+ % + пт *
"
228
E142
Jue [e107 Fis? асое aa | | ЕВ
104 _[22/4т 926 = == |100 =
= s= KRASOG RX vee
us "
R1120N4018 k
и IS
4 гв М Р
KDS184 9:54 168 Е B É K
CHARGER- L N 2 N
2-сом. CO.,LTD.
PCB : 591-0423-A (7)
Krs
Tectalk
Tze Pocument Number REV
в Tectalk.SCH P?
ate: November 7, 200iBheet of
7. SCHEMATIG
Egg EIE n apre
Е]
SEE
AER
MAP
нге | | L+ |
C57 | [53]
m
sl In
[142 [С77 Ірі
= [一 一
dass
E m а
ШЕЕ:
ӨЗЕГІМДІ
М ee erc HD40488
= Bil es ASHORTI -12B28TE( V4}
sint
591-0423-А-? таки
2001.01.09
lv
BaszATr-
ЗЕТ
Les
| T Е REF, VALUE MAr
mn x| x}
mx) xD
ої хі ж
-ш
a
ап — М)
E
MIC1
СМР45 48
оо
8. СОМРОМЕМТ PARTLIST
Tectalk Revised: November 7, 2001
Tectalk.SCH Revision: 22?
Bill Of Materials November 8, 2001 9:18:20 Page
Мет Quantity Reference Part
1 1 ANT ANT
2 1 C9 BD
3 7 C1,C12,C30,C42,C43,C63, АР
С81
4 21 C13,C14,C17,C19,C20,C21, 102
C23,C31,C52,C55,C64,C82,
C83,C92,C112,C113,C127,
C141,C147,C149,C154
5 13 C2,C41,067,C78,C79,C89, 220P
C91,C93,C94,C95,C109,
C155,C163
6 4 C15,C44,C45,C46 6Р
7 5 C16,C36,C47,C48,C75 10Р
8 27 C18,C26,C28,C33,C34,C51, 104
C56,C57,C65,C115,C118,
C121,C123,C125,C129,C134,
C140,C145,C146,C148,C159,
C164,C169,C171,C172,C173,
С175
9 7 C22,C35,C61,C66,C88,C122, 1u
C142
10 10 C24,C32,C111,C114,C130, 103
C131,C143,C153,C161,C162
11 1 С27 474
12 1 С29 100Р
13 1 C37 ЗОР
14 1 Сз8 56PU
15 1 C39 33P
16 1 C49 2P
17 2 C53,C59 15P
18 1 C54 12P
19 4 C62,C68,C71,C74 1P
20 2 C69,C72 8PU
21 1 C73 3P
1
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
С76
C84,C156
C85
C86,C157
С101,С103,С107
OP1,C
C105
C106
C124,C126,C128
С132,С177
С133
С152
С174
С220
СЕ1
497, СНАВСЕВ-
03,06,07,010
05,08
022
D
D1
D9
D11
D21
D25,D26
E7
H1
J1
JA
L1
L2,L11,L17
L3
2P2
224
3.3/6T3
223
22/4T
OPEN
100/6ЕЗ
47/16Е
22Р
393
820P
473
472
220/6ЕЗ
CF450UG
KDS114
KDS160
SM-2333T,GRN
off
МА25372
KDS226
KDS120
SR-2333H,RED
KDS184
XX3P
30mmX2 WIRE
STERO
22X1
10n,(E2-320904T-R)
470n,(FI-B1608)
47n,(CI-B1608)
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
24
14112 270n,(FI-B1608)
L5,L7,L8,L15 24n,(E2-281 106T-R)
L6,L18 28n,(E2-281 106T-R)
19 22n,(CI-B1608)
L10 39n,(CI-B1608)
113 31n,(E2-281106T-R)
L16 8n2,(CI-B1608)
LCD1 TTR3264DPFDHN
MIC1 CMP4540
Q3 KTC4080
Q4 AT-31625
Q5 BFP193
01,02,07,08,010 BFQ67W
019,023,027,028,029,031, KRC404
032,033
Q9 25С4226
021,024,026 KRA306
Q22 KTA2015
Q25 KRA305
Q30,Q35 KRA304
Q34 KRC409
R3,R53,R101,R102 330
R1,R4,R21,R43,R45,R49, 4K7
R106,R107,R108,R141
R7,R20,R26,R33 1K
R8,R10,R40 100
R2,R5,R15,R19,R24,R30, 10K
R31,R32,R34,R35,R38,R41,
R52,R105,R112,R114,R126,
R127,R128,R129,R131,R132,
R152,R155
R9 3K3
R11,R44,R54 470
R13,R22,R148,R159 2К2
R14,R17 0
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
R16,R48
R18,R123,R125
R23,R29,R111,R122,R143,
R147,R151,R154,R160,R174
R25,R37
R28
R39
R47,R55
R12,R103
R104
R109,R156
R120
R121,R136
R124
R135
R153
R158
R171
R172
R173
SF1,SF2
SPK1
SW1,SW2
Ti
TP
UT
U2
U3
UA
U5
U6
U7
47K
470K
100K
220
20K
22
10
330K
390K
1M
120,0.5W
22K
7K5
12K
82K
2К7
15К
270К
33K
446M
36-16BB-08
KQT901
T13
TP
HD40488-12B28TE(V4)
CMX808A
R1120N401B
NJM386
AK93C45AV-L
NJM2072M
NJM324V
114
115
116
117
118
119
120
121
122
08
U11
U12
VC1
VC2
VR1
X1
х2
ХЕ1
R1120N331B
TB31202FN
DBL5018V
3PM
10PM
10KM
4MHz
21.25MHz
MF21.7M3
9. ASSEMBLY DRAVVING AND РНОТОСВАРН
гав newera | Lue es | тїтїнї: | 1 |
| zum | coven wr а |
ее [inner sms аласн |1
[25 | zoe-mie-A | SCREW MACHINE (вн, Nenze, нҥт апатай] 2 |
[5 | wwe tnr әне) каша ттш | e |
г [cun | aia | кми, aae | 1 |
[22 | mem | SCREW mont [eaaet ee ^N -PLATIHE 1 |
[лыма axmm | m ||
[a | тшм] ато | rumoer |1)
jën | леш» | sm | n
9 1 meam | шгп | ostro» enema |!)
[% | ?msn | contact agar Pas ke, RUNS | 1 |
[7 | те-ша-а | CONTACT BATT ^ |медізнну M58FPLATD5| 1 |
Al | m | mw |1)
(35 | лашы | шы но | SLICNE, фев | 1 |
[4 | same | oven совести | холоне, нз |1|
ETEN | тшк | mm [1|
pëj | a J |
[u | remsa | шаш |
DEAE
19 | moea (taven wick |
[s| моон Lom | Fepiare, a, mss Tare | | |
+ mm |]
32 mme | am [|
pë [жеш | анат” | нова vene [1]
vera | amer | Pn ans | |
[L| миш |
| mer | TESCRIATIEN [тї] ню
10. CHANNEL DATA (With Sub-channel data)
446.05625
446.06875
446.08125
446.09375
CTCSS (Continuous Tone Coded Squelch System) Frequency List
67.0 Hz 136.5 Hz
Sub Channel Tone Frequency Sub Channel Tone Frequency
71.9 Hz 141.3 Hz
74.4 Hz 146.2 Hz
77.0 Hz
ПО ELE
э
11
151.4 Hz
156.7 Hz
82.5 Hz 162.2 Hz
85.4 Hz 167.9 Hz
рони EE RUN.
94.8 Hz 186.2 Hz
97.4 Hz 192.8 Hz
12 100.0 Hz 203.5 Hz
13 103.5 Hz 210.7 Hz
14 107.2 Hz 218.1 Hz
15 110.9 Hz 225.7 Hz
16 114.8 Hz 233.6 Hz
8
17 118.8 Hz 241.8 Hz
© ALAN Electronics GmbH November 2001
www.albrecht-online.de/service