Document text
ENGINEERING, LLC
1650 PACIFIC AVENUE * CHANNEL ISLANDS, CA 93033-9901 • (805) 247-0226
FAX (805) 247-0669 * www.vortechsuperchargers.com * M-F 8:00 AM - 4:30 PM PST
FOREWORD
Proper installation of this supercharger kit requires general automotive mechanic
knowledge and experience. Please browse through each step of this instruction manual
priorto beginning the installation to determine if you should refer the job to a professional
installer/technician. Please call Vortech Engineering for installers in your area.
© 2003 VORTECH ENGINEERING, LLC
All rights reserved. No part of this publication may be reproduced, transmitted, transcribed,
or translated into another language in any form, by any means without written permission
of Vortech Engineering, LLC.
P/N: 4FM020-010
© 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured oe
200CT03 v3.1 4.6/5.4Exped/Nav(4FM v3.1) Il
P/N: 4FM020-010
€ 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured
TOOL & SUPPLY REQUIREMENTS
PARTS LIST - 1997-2001 FORD 4.6L 2V F-150/F-250
PARTS LIST - 1997-2001 FORD 5.4L 2V F-150/F-250
COMPONENT REMOVAL AND PREPARATION ................................................
OIL FEED EINE-INSTALLAT]IGON,...... co ctetu dt det nt tuens
הטיו — Т
CRANKSHAFT PULLEY/SUPERCHARGER DRIVE צם ]וק ee
e MIS ——————————— ER
FUEL BILLARD €
WIRE PREPARATION (4.6 Models only) .................... sse
Table Of Contents
MAIN MOUNTING PLATE ASSEMBLY AND MOUNTING (4.6 Models only) .....
MAIN MOUNTING BRACKET ASSEMBLY AND MOUNTING (5.4 Models only)
EGR CONTROL MOUNTING AND MAIN MOUNTING PLATE SUPPORT
(4:6. Модеј TEE
FUEL MANAGEMENT UNIT (EMU...
IDLER AIR CONTROL RESONATOR AND CRANKCASE VENT HOSE
iiri EE EE EE ו
SUPERCHARGING MOUNTING ................. esee emen
MASS AIR FLOW SENSOR REMOVAL, MOUNTING AND ASSEMBLY ...........
AIR INLET/BYPASS ASSEMBLY eene emnes
Belice" "—————————————————— eset ties
RINAL שכר
Ш 2000103 v3.1 4.6/5.4Exped/Nav(4FM v3.1)
FOREWORD
TABLE OF CONTENTS
DISCLAIMER
NOTICE
1.
SU, ו ילש cR cp ГО
8B.
10.
11.
12.
13.
14.
15.
16.
SUPERCHARGED F-150/F-250/EXPEDITION/NAVIGATOR
DISCLAIMER
Towing, racing performance driving, hard accelerations, and other heavy/severe duty driving
activities place extra demands on a vehicle’s transmission. If you use or plan to use your
supercharged '97 or later Ford F-150, F-250, Expedition under any of these special driving
circumstances, Vortech suggests that you evaluate the purchase of a transmission shift improver
product. In simple terms, a transmission shift improver product is designed to improve the
performance and durability of your vehicle's transmission.
Several companies make these shift improver products including TransGo Performance. Please
contact TransGo Performance or one of the other product companies directly should you wish to
obtain more information about their shift improver products.
TransGo Performance
2621 Merced Avenue
El Monte, CA 91733
(626) 443-4953 phone
(626) 443-1079 fax
NOTE: This listing is provided solely for informational purposes.
VORTECH has made no evaluation of the quality or function-
ality of these products and DOES NOT MAKE ANY RECOM-
MENDATION, ENDORSEMENT, NOR PROVIDE ANY WAR-
RANTY ON ANY OF THESE SHIFT IMPROVER PRODUCTS.
* Only applies to vehicles equipped with automatic transmissions.
P/N: 4FM020-010
€ 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured t
2000103 v3.1 4.6/5.4Exped/Nav(4FM v3.1) IV
P/N: 4FM020-010
© 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured
IMPORTANT NOTES
1999-2003 Models
This kit requires ECM modification and the installation of a Vortech/Superchips ECM
Module. The ECM must be sent directly to Vortech by the installing customer (the charge
for this service with module installation has been included in the purchase price).
e Included in this kit is SE next-day air shipping box and a credit tag for one (1)
Vortech/Superchips ECM Module.
e The modules are made specifically for each individual vehicle with respect to the
factory ECM calibration.
e Simply contact the Vortech Service Department at (805) 247-0226 to request a
Return Authorization Number (See ECM Module Credit Tag for more details).
- Mail to Vortech the enclosed "ECM Module Credit Tag" (send original tag - no
photocopies will be accepted) and ECM in the supplied box.
- Turnaround time will be 1-2 days (each application varies). Vortech will give an
estimate at the time of your order.
Your Vortech/Superchips ECM Module comes with a twelve (12) month limited
warranty from the original date of purchase of your supercharger system (see
Owner's Manual for details).
NOTE: Vortech Engineering is not responsible for engine or ECM damage due
to an improperly installed/mishandled ECM module or ECM.
This product is protected by state common law, copyright and/or patent. All legal rights
therein are reserved. The design, layout, dimensions, geometry, and engineering
features shown in this product are the exclusive property of Vortech Engineering, LLC.
This product may notbe copied or duplicated in whole or part, abstractly or fundamentally,
intentionally or fortuitously, nor shall any design, dimension, or other information be
incorporated into any product or apparatus without prior written consent of Vortech
Engineering, LLC.
V 2000103 v3.1 4.6/5.4Exped/Nav(4FM v3.1)
1997-2003
FORD 4.6L, 5.4L 2V F-150/F-250/EXPEDITION/NAVIGAT OR
Installation Instructions
CARB EO #D-213-20
Congratulations on selecting the best performing and best backed automotive supercharger available today...
the VORTECH? V-2? Supercharger!
Before beginning this installation, please read through this entire instruction booklet and the Street Supercharger System
Owner's Manual which includes the Limited Warranty Program and the Warranty Registration form and return envelope.
Vortech supercharger systems are performance improving devices. In most cases, increases in torque of 30-35% and
horsepower of 3595-4576 can be expected with the boost levels specified by Vortech Engineering. This product is intended for
use on healthy, well maintained engines. Installation on a worn-out or damaged engine is not recommended and may result in
failure of the engine as well as the supercharger. Vortech Engineering is not responsible for engine damage.
Installation on new vehicles will not harm or adversely affect the break-in period so long as factory break-in procedures are
followed.
For best performance and continued durability, please take note of the following key points:
Use only premium grade fuel 91 octane or higher (R+M/2).
The engine must have stock compression ratio.
If the engine has been modified in any way, check with Vortech prior to using this product.
Always listen for any sign of detonation (pinging) and discontinue hard use (no boost) until problem is
resolved.
5. Perform an oil and filter change upon completion of this installation and prior to test driving your vehicle.
Thereafter, always use a high grade SF rated engine oil or a high quality synthetic, and change the oil and
filter every 3,000 miles or less. Never attempt to extend the oil change interval beyond 3,000 miles,
regardless of oil manufacturer's claims as potential damage to the supercharger may result.
6. Before beginning installation, replace all spark plugs that are older than 1 year or 20,000 miles with
original heat range plugs as specified by the manufacturer and reset timing to factory specifications
(follow the procedures indicated within the factory repair manual and/or as indicated on the factory
underhood emissions tag). Do not use platinum spark plugs unless they are original equipment. Change
spark plugs every 40,000 miles and spark plug wires at least every 60,000 miles.
TOOL & SUPPLY REQUIREMENTS
* Factory Repair Manual
* 3/8" Socket and Drive Set: SAE & Metric
* 1/2" Socket and Drive Set: SAE & Metric
* 3/8" Extension 3"
* 1/2" Extension 3"
* 3/8" NPT Tap and Handle
* Adjustable Wrench
* Harmonic Balancer Puller
* Harmonic Balancer Installer
• Open End Wrenches: 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 11/16", 3/4"
10mm, 13-18mm, 18mm tappet (thin) wrench
= с № ~
• 3 lb. Hammer
e 1-1/16" Oil Sending Unit Socket (Snap-on #A119A)
* Center Punch and a 5/8" Tapered Punch
* Ford Springlock 3/8" Fuel Fitting Disconnect Tool
* 6 Quarts SH/CF Rated Quality Engine Oil
* Oil Filter and Wrench
* Hat #2 Screwdriver
* Phillips 42 Screwdriver
* Heavy Grease
* Silicone Sealer
* Drill Motor
• "А", 1/8", 3/16", 11/32" Drill Bits
* 3/16", 8mm Allen Wrenchs
* Wire Strippers and Crimpers
* Utility Knife
* 1/8" NPT Tap (for 4WD models equipped with oil coolers)
P/N: 4FM020-010
€ 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured А
2000103 v3.1 4.6/5.4Exped/Nav(4FM v3.1) И
=== 1997-2001 Ford 4.61 2V F-150/F-250/E xpedition/Navigator
== Раг® Мо. 4ЕМ218-0105/0185
b ENGINEERING, LLC PARTS LIST
IMPORTANT: Before beginning installation, verify that all parts are included in the kit. Report any shortages or damaged parts immediately.
Part Number Description Quantity Part Number Description Quantity
2E228-160 SUPERCHARGER ASSEMBLY 1 8F203-265 FUEL PUMP ASSEMBLY 1
2E128-230 V-2 Supercharger 1 5W001-001 Wire Tap 1
2A036-361 3.60 Supercharger Drive Pulley 1 5W001-011 16-14 Ga. Eyelets 2
7100-070 3/16" x 3/16" x 7/8" Key 1 7E010-050 %12 x 1/2" Sheet Metal Screw 1
2A040-011 Pulley Retainer 1 7P312-003 5/16" Female Fuel Connector 1
7B375-125 3/8-24 x 1-1/4" HXHD Bolt 1 7R004-003 14.5 Stepless Clamps 2
7K375-040 3/8" AN960 Flat Washer 1 7U100-044 4" Tie Wraps 3
7U100- 6” Tie W 4
4FM111-034 MAIN MOUNTING BRACKET ASSEMBLY 1 Gate gue High Pressure — 1
4FM011-033 Mounting Plate Assembly 1 8F101-200 T-Rex Wiring Assembly 1
7A375-251 3/8-16 x 2-1/2” Flat SHCS 5
5W001-014 Fuse Holder 1
7C100-085 10mm x 1.50 x 85mm HXHD Bolts 3
7K437-001 7/16" AN Wash 3 5W001-015 20A Blade Type Fuse 1
ay ashers 5W001-010 16-14 Ga Female Slides 3
8C080-020 8mm x 1.25 x 20mm HXHD Bolt 1 7030-050 19mm x 16" Fuel Hose 1
ТЗП 00 5/16" AN Washer | 8F001-002 155 Inline Fuel Pump 1
4FM010-130 Bracket Support Strut 1 7R003-024 4-1/2" Adel Clamp 1
7375-100 3/8-16 x 1" HXHD Bolt 1 7R001-008 #8 Hose Clamps 9
EE К ל | 7Е010-075 #12 x 3/4" Sheet Metal HXHD Bolt 1
j а Masher 7P500-004 1/2" Fuel Fitting Adapter 1
7R003-008 1/2" Adel Clamp 1
5W018-010 6" 18 Ga. Std. Red Wire 1 AEN 112-010 AIR INLET ASSEMBLY 1
5W001-007 3/16" x 6" Heat shrink Tube 1 4FM010-050 MAF Bracket Assembly 1
7C080-085 8mm Shoulder Bolts 4 8H040-045 3-3/4" Flanged Air Filter 1
7R002-056 #56 Hose Clamps 4
4FM 110-040 COIL/EGR/POWER STEERING ASSEMBLY 1 75350-200 3-1/2" x 2" Ste 2
4FM010-040 Coil Mounting Bracket 1 00 3-1/2” א 15" Flex Hose 1
ee . So Bolts 4 70100-052 7/16" Rubber Grommet 1
101002 а а 8 7038-000 3/4" x 24" Heater Hose 1
a #10 Flat Washers 12 7P500-026 1/2" NPT x 3/4" -90° Hose Barb 1
7250-075 1/4-20 x 3/4" SH Cap Screws 4 7P375-052 3/8" NPT x 5/8" 90° Hose Barb 1
7F250-021 1/4-20 Nylock Nuts 4 4FA012-012 90? Intake Elbow 1
E | на | 4FA012-013 90° Intake Elbow w/Boss 1
010-030 А Bracket 7250-075 1/4-20 x 3/4" SH Cap Screws 4
7010-050 10-24 x 1/2" SH Cap Screws 4 7F250-021 1/4-20 Nylock Nuts 4
4FM111-032 SUPERCHARGER DRIVE ASSEMBLY 1 7J250-001 1/4" SAE Washers 4
4FM01 1-032 Belt Tensioner 1 7U100-055 6" Tie Wraps 6
2A046-725 Belt 1 7A312-150 5/16-18 x 1-1/2" HXHD Cap Screws 2
72 12mm Flat Washers 3 1 5/16" Fender Washers 2
7C012-020 12mm x 1.75 X 20mm Bolts 5 7J312-000 5/16' SAE Flat Washers 2
7012-022 12mm x 1.75 X 20mm Thin Head Bolt 1 7F312-017 5/16-18 Nylock Nuts 2
4FA016-150 Smooth Pulley Tensioners 2 7U030-065 3/4" x 90° Hose 1
4GF016-160 Ribbed Idler Pulley 1 7U133-024 5/8" Molded Elbow Hose 1
4FK116-021 Idler Pulley Assembly 1 7P750-102 3/4" NPT x 1"90° Hose Fitting 1
0-55 10mm א 1.50 x 85mm HXHD Bolt 1 7R002-052 #52 Hose Clamps 2
Ger m es ו | 4FM238-068 FMU (with lines) 1
017-02 pacer 1 62110-114 8:1 Fuel Management Unit 1
АРМО16-011 Balancer | 4FA145-010 Male Fuel Line 1
7C080-026 8mm x 125 x 25mm SH Bolts 3 AFA145-020 Female Fuel Line 1
io 5/16" AN Washers 3 70030-046 5/32" x 18" Vacuum Line 1
7120-065 12mm x 1.5 x 65mm HXHD Bolt 1 7P156-082 5/32" Tee 1
7438-071 7/16" USS Washer 1 70100-055 6" Tie Wraps 4
4FM016-012 Crank Pulley 1
4FM130- IL DRAIN ASSEMBLY 1
4FM112-020 DISCHARGE ASSEMBLY 1 S e x 32" Oil .- Boss 1
.- Se SR Tube | 78001-008 #8 Stainless Hose Clamps 2
EH 2 SÉ Я >» Se 1 2 Male Connector 1
4FH100-01 il Drain Tube Nut Assy. 1 ` ו
7R002-044 144 Hose Clamps 2 07910 O Drain Mee КАЗУ
а e is Ge 2 4FM130-026 OIL FEED ASSEMBLY 1
Mies | ü : DUE . 70030-026 1/4" x 36" Oil Feed Hose 1
8000 - M ugs ל 7P525-067 .525 Crimp Ferrules 2
ee 5 XT GE SE | 7Р250-066 -4 Swivel x 1/4” Hose Barb Fittings 2
7U034-016 "х 9" Heater Hose 7P125-026 1/8" NPT x #4 -90° Fitting 1
06 5/32” א 12” Vacuum Line 1 7100-055 6" Tie Wraps 4
Ld des Ps | | 7P250-082 1/4" NPT x -4 -90° Fitting 1
eer xs | ты | 7Р250-122 1/4" Pipe Thread Тее 1
7Р375-106 CV Маме 7P250-123 1/4" NPT x 1-1/2" Nipple 1
7P250-034 1/4 NPT Strt. Tee 1
7U030-026 1/4" x 62" Oil Feed Hose 1
7P125-103 1/8" NPT x 45" #4 Ад. 1
P/N: 4FM020-010
€ 2003 Vortech Engineering, LLC
éi All Rights Reserved. Intl. Copr. Secured
Vil 200CT03 v3.1 4.6/5.4Exped/Nav(4FM v3.1)
1997-2001 Ford 5.4L 2V F-150/F-250/Expedition/Navigator
Part No. 4FM218-020/028S
PARTS LIST
ENGINEERING, LLC
Quantity
DO — — а NO OO РӘ Ср ДУ Es Де а а а а а а а ро E — а
— о eh к = = по РӘ = = wh
= = о о = = E ч По כ\ + vc
= амраа
Description
AIR INLET ASSEMBLY
MAF Bracket Assembly
3-3/4" Flanged Air Filter
#56 Hose Clamps
3-1/2” x 2" Sleeves
3-1/2” x 15" Flex Hose
7/16” Rubber Grommet
3/4” x 24” Heater Hose
1/2" NPT x 3/4” -90° Hose Barb
3/8" NPT x 5/8” -90° Hose Barb
90° Intake Elbow
90° Intake Elbow w/Boss
1/4-20 x 3/4” SH Cap Screws
1/4-20 Nylock Nuts
1/4” SAE Washers
6” Tie Wraps
5/16-18 x 1-1/2" HXHD Cap Screws
5/16" Fender Washers
5/16' SAE Flat Washers
5/16-18 Nylock Nuts
3/4" x 90° Hose
5/8" Molded Elbow Hose
3/4" NPT x 1"90° Hose Fitting
#52 Hose Clamps
5.4 DISCHARGE ASSEMBLY
Discharge Tube 5.4 (Only)
5/32” TEE
#16 Hose Clamps
#44 Hose Clamps
#48 Hose Clamps
2-3/4” x 2” Sleeve
3” x 2” Sleeve
5/32" x 12" Vacuum Line
1"x 9" Heater Hose
1"x 2.5" Heater Hose
Bypass Valve
PCV Valve
OIL FEED ASSEMBLY
1/4" x 36" Oil Feed Hose
.525 Crimp Ferrules
-4 Swivel x 1/4” Hose Barb Fittings
1/8" NPT x #4 -90° Fitting
6” Tie Wraps
1/4" NPT x -4 -90° Fitting
1/4" Pipe Thread TEE
1/4" NPT x 1-1/2" Nipple
1/4" x 62" Oil Feed Hose
1/4" NPT Strt. TEE
1/8" NPT x 45" #4 Fitting
OIL DRAIN ASSEMBLY
1/2” x 32” Oil Drain Hose
#8 Stainless Hose Clamps
Male Connector
Oil Drain Tube Nut Assy.
MAF CLAMP ASSEMBLY
Part Number
4FM112-040
4FM010-050
8H040-045
7R002-056
78350-200
7U035-000
7U100-052
7U038-000
7P500-026
7P375-052
4FA012-012
4FA012-013
7A250-075
7F250-021
7J250-001
7U100-055
7A312-150
2071
000
7F312-017
7U030-065
7U133-024
7P750-102
7R002-052
4FM112-030
4FM012-030
7P156-082
7R002-016
7R002-044
7R002-048
78275-200
78300-200
7U030-046
7U034-016
7U034-016
8D001-001
7P375-106
4FM130-026
7U030-026
7P525-067
7P250-066
7P125-026
7U100-055
7P250-082
7P250-122
7P250-123
7U030-026
7P250-034
7P125-103
4FM130-036
7U030-036
7R001-008
7P375-042
4FH100-010
5A101-016
viii
Quantity
ee oo ee = = =
BSB а а а = = ~ бо Ол МО а = Со - 09 СО бэ МО -+ Су а а МО а а а о а =
— AN а а а о а а а а Д Со МО а а כ\] а а а Со а Q)-- а а а а а а а
ГСКЕ = kb SE ect:
IMPORTANT: Before beginning installation, verify that all parts are included in the kit. Report any shortages or damaged parts immediately.
Part Number Description
2E228-170 SUPERCHARGER ASSEMBLY
2E128-220 V-2 Supercharger
2A038-333 3.33 8 Rib Pulley
7U100-070 3/16" x 3/16" x 7/8" Key
2A040-011 Pulley Retainer
7B375-125 3/8-24 x 1-1/4" HXHD Bolt
7K375-040 3/8" AN960 Flat Washer
4FM111-054 MAIN MOUNTING BRACKET ASSEMBLY
4FA016-170 Idler Smooth
4FA016-171 Dust Shields
4FM010-140 Bracket Support
4FM010-150 Bracket Support #2 5.4
4FM011-021 Mounting Bracket Mach.
4FM016-031 Idlers Grooved
4FM017-010 Spacer Short Bracket Support 2
4FM017-020 Spacer Long Bracket Support #2
7A250-075 1/4-20 x 3/4" S.H.C.S.
0 1/4-20 א 1" Flat Allen
7A375-175 3/8-16 x 1.75" Hex Head
7A375-250 3/8-16 x 2.5" Hex Head
7A437-150 7/16-14 x 1.5" Bolt Hex Head
7C010-080 10mm x 1.5 x 80mm S.H.C.S.
7060-016 M6 x 1.00 x 16 HXHD Bolt
7F250-021 1/4-20 Nylock Nut
7J006-093 6mm Washer
7J250-001 1/4 SAE Washer Plated
7J438-091 9/16 SAE Washers Plated
7K375-040 3/8" AN 960 Flat Washer
7010-002 10mm Washer
5W001-012 Solderless Connector
5W001-006 3/8" Heat Shrink Tubing 12"
700 14mm x 2.0 א 30mm HXHD
5W018-070 18 GA Wire Green 12"
5W018-030 18 GA Wire Grey 12"
7P375-050 3/8 Hose Mender
0-04 #4 Hose Clamp
7U032-016 3/8" Hose Hi-Pressure 18"
4FM010-160 Power Steering Bracket
4FM 111-062 SUPERCHARGER DRIVE ASSEMBLY
2A048-802 Belt 8 rib x 80.14"
4FA016-170 Idler Smooth
4FA016-171 Dust Shields
4FM011-052 Spring Tensioner Long Ford
4FM016-011 Balancer
4FM016-041 Crank Pulley, 8 Rib
7A375-324 3/8-16 x 3.25" HXHD Bolt
7C010-045 10mm x 1.5 x 45mm Hex Head
7C080-026 8mm x 1.25 x 25mm SH Bolts
7C120-065 12mm x 1.5 x 65mm HXHD Bolt
7J438-071 7/16" USS Washer
7K312-001 5/16" AN Washers
7K375-040 3/8" AN 960 Flat Washer
8F203-265 FUEL PUMP ASSEMBLY
5W001-001 Wire Tap
5W001-011 16-14 Ga. Eyelets
7E010-050 #12 x 1/2" Sheet Metal Screw
7P312-003 5/16” Female Fuel Connector
0.03 14.5 Stepless Clamps
7U100-044 4” Tie Wraps
7U100-055 6” Tie Wraps
7U031-018 5/16” x 11” High Pressure Fuel Hose
8F101-200 T-Rex Wiring Assembly
5W001-014 Fuse Holder
5W001-015 20A Blade Type Fuse
5W001-010 16-14 Ga Female Slides
70 12mm א 16” Fuel Hose
8F001-002 155 Inline Fuel Pump
7R003-024 1-1/2" Adel Clamp
7R001-008 #8 Hose Clamps
7E010-075 #12 x 3/4" Sheet Metal HXHD Bolt
7P500-004 1/2" Fuel Fitting Adapter
AEN 238-068 FMU (with lines)
4 8:1 Fuel Management Unit
4FA145-010 Male Fuel Line
4FA145-020 Female Fuel Line
7U030-046 5/32” x 18” Vacuum Line
7P156-082 5/32” TEE
7U100-055 6” Tie Wraps
P/N: 4FM020-010
€ 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured
2000103 v3.1 4.6/5.4Exped/Nav(4FM v3.1)
*4.6 MODELS ONLY
P/N: 4FM020-010
© 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured
2000103 v3.1 4.6/5.4Exped/Nav(4FM v3.1)
COMPONENT REMOVAL AND PREPARATION
A. Disconnect the negative battery cable.
NOTE: 1999-2003 Models Only
1. Remove the passenger side front kick panel from
the interior of the vehicle. Remove the sound
deadening material (if any) that is EE the
ECM. Remove the plastic ECM hold-down
bracket.
2. From the engine side of the firewall (in the en-
gine compartment), use a 10mm socket or
wrench and remove the harness and plug from
the ECM (as you loosen the bolt, the connector
will slowly release). Remove the ECM from the
vehicle.
3. Contact the Vortech Service Department for a
Return Authorization Number. Send both ECM
and supplied credit tag to Vortech using the en-
closed shipping box.
B. Remove the throttle body/throttle linkage cover.
C. Detach the crankcase ventilation tube from the driver's
side valve cover and the air inlet.
D. Remove the idle air control resonator and air filter
cover.
E. Unplug the intake air temperature sensor (IAT) and
the mass air flow (MAF) sensor.
F. Detach all remaining components of the air inlet as-
sembly and set aside.
«а. From the left side coil, unplug the radio ignition inter-
ference capacitor, remove the spark plug wires and
coil plug.
*H. Remove the cam trigger plug, unbolt the coil and re-
move the coil bracket.
*|. Separate the EGR pressure transducer and the EGR
vacuum regulator solenoid from their bracket, unbolt
the bracket from the intake manifold and set aside.
J. Unbolt the power steering fluid reservoir from its
bracket. Separate the throttle cables from the retainer
bracket. Remove the main bracket from the waterneck
and the head and set aside.
K. Remove the plastic wire harness holder mounted on
the upper row of valve cover bolts on the driver's side.
L. Remove the accessory drive belt and set aside.
1.
2WD only
1/4” NPT
nipple
1/4” NPT
> tee
% 1/4” NPT א 4
> Ka flare
Factory
sending unit
VIEW FROM FRONT
Fig. 2-a
AWD Only (without oil cooler)
Remote oil filter
hole assembly
Factory oil
sending unit
location (remove)
DRIVER’S
SIDE VIEW
Fig. 2-b
1/4” NPT x -4
flare
Oil feed to
יי supercharger
1/4” NPT
street tee
ENGINE
BLOCK Relocated sending unit
Remote oil
filter hose
assembly
TOP VIEW
Fig. 0
2. OIL FEED LINE INSTALLATION
A. Unplug the connector on the oil pressure sending unit.
Remove the sending unit from the engine block. (The
unit is located on the left front side of the engine, just
above the oil pan.)
B. Thread the supplied 1/4" NPT fittings into the block as
shown. Reinstall the sending unit and connector.
4WD applications only (without oil cooler)
e Remove the remote oil filter hose assembly from the two
studs on the engine block. Disconnect the factory oil
sending unit connector and remove the sending unit.
* Following the graphic for 4WD applications, attach the
supplied 1/4 NPT straight TEE and 90? fitting into the
hole previously occupied by the oil sending unit. Attach
the oil sending unit into the remaining 1/4 NPT opening
in the TEE.
e Reconnect the oil filter hose assembly to the original
location on the engine block. Make sure the gasket is in
its proper location. Replace gasket if needed.
e Reattached connector to sending unit.
4WD applications only
(equipped with factory oil cooler)
* Remove the oil filter from the filter base located behind
the front bumper of the vehicle.
* Remove the oil filter base mounting bracket from the
frame. Remove the oil filter mounting base from the
bracket.
e Mark the base in the same location as shown in the photo.
Center punch the previously marke spot on the base (make
sure that the spot is marked on the center port of the
filter base). Drill with an 'R' size drill bit and thread with a
1/8" NPT tap.
e Thoroughly clean and blow dry the filter base taking care
to remove any chips or burrs.
P/N: 4FM020-010
€ 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured
2000103 v3.1 4.6/5.4Exped/Nav(4FM v3.1) 2
2. OIL FEED LINE INSTALLATION, cont'd.
* Using alight amount of oil on the threads for lubrication, 4WD (equipped with factory oil cooler)
thread the 1/8" NPT x 45? x %4 fitting into the threaded
hole. Teflon tape, paste or other sealant is not
recommended as it might loosen and cause blockage of
the oil feed orifice, resulting in supercharger failure. Rotate
the fitting so that when it is tight, it will face the front of
the vehicle.
e Reassemble the oil filter base and bracket and secure
onto the vehicle. Reinstall oil filter.
WARNING: Use engine oil on the pipe threads, Teflon
tape, or sealant is not recommended as it
might loosen and cause blockage of the oil Punch | |
feed orifice resulting in supercharger failure. Center Punch location (x)
C. Temporarily cap off the flare fitting to prevent dirt from Fig. 2-d
entering the oil feed, it will be connected to the
supercharger at a later time.
3. OIL DRAIN
А. To provide a proper oil drain for the supercharger it is
necessary to make a hole іп the oil pan. The best way
to provide this hole is to punch the hole rather than
drill it.
B. Locate the appropriate area for the through hole as
shown in the following illustration, remove the paint
around the hole area. (Transmission cooler lines may
need slight bending to achieve oil drain tube and fit-
ting clearance).
C. Usea small center punch to perforate the pan, ex-
pand the hole to approximately 9/16” diameter. Most
punches are made from a hexagonal material and may
be placed in a socket to make this task easier. |
D. Tapthehole with a 3/8" NPT pipetap
approximately 1/4" deep. Pack the
pipe tap flutes with heavy grease to
hold the chips and use a small mag-
net to check for any stray chips.
OIL PAN
FRONT VIEW
Fig. 3-a
P/N: 4FM020-010
€ 2003 Vortech Engineering, LLC
3 All Rights Reserved. Intl. Copr. Secured
2000103 v3.1 4.6/5.4Exped/Nav(4FM v3.1)
3. OIL DRAIN, cont'd.
NOTE: This method of rolling over the lip of the
hole and tapping works very well if care-
fully done and should cause no problem.
E. Thoroughly clean the threaded area. Apply a small
amount of silicone sealer to the new threads. Apply
more sealer to the 3/8" NPT x 1/2" inverted flare fitting
and secure in hole. Make sure a seal is formed all
around the fitting.
F. Thread the tube nut and 1/2" x 90° aluminum tube
into the inverted flare fitting by hand. Do not tighten
until after the supercharger drain hose has been con-
nected.
G. Drain the engine oil and change the oil filter.
H. Temporarily cap off the oil drain fitting to keep out
debris until the drain hose is attached to the super-
charger at a later time. FRONT VIEW
|. Refill engine with 5W/30 synthetic or conventional SH/ Fig. 3-b
DRAIN HOSE
FROM
SUPERCHARGER
OIL
DRAIN
TUBE
CF rated motor oil.
CRANK
PULLEY
L
©
ы o o
OIL PAN
VIEW FROM PASSENGER SIDE
Fig. 3-с
P/N: 4FM020-010
€ 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured 4
2000103 v3.1 4.6/5.4Exped/Nav(4FM v3.1)
P/N: 4FM020-010
© 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured
200CT03 v3.1 4.6/5.4Exped/Nav(4FM v3.1)
4. CRANKSHAFT PULLEY/SUPERCHARGER DRIVE PULLEY
NOTE: This process can be done with the fan
shroud and radiator in place providing your
balancer puller is equipped with a 5” or
shorter forcing screw. Removing the fan
shroud and the radiator will allow easier
access to the crank pulley and the front of
the engine.
A. Remove the rubber inspection plug on the left rear of
the block to make the flexplate accessible. Using an
18mm socket and a 1/2” drive ratchet, rotate the en-
gine until a flexplate nut is visible. Place a 14mm deep
socket and extension on the flexplate nut and rotate
the engine counterclockwise until the socket engages
with the top of the access hole. This will block the
movement of the crankshaft allowing the bolt to be
loosened. This operation may require the assistance
of another person. Remove the center balancer bolt.
B. Install the harmonic balancer puller. Evenly start three
puller bolts (not supplied - 8mm x 1.25 on the 4.6L
and 10mm x 1.50 on the 5.4L). Engage the forcing
screw against the pivot and check alignment.
NOTE: When using the harmonic balancer
puller pay special attention to alignment
of the forcing screw and pivot, improper
alignment can result in damage to the
crankshaft.
C. After ensuring the puller is properly aligned on the
face of the crank, slowly tighten the forcing screw until
the harmonic balancer has been removed.
NOTE: The factory uses a small amount of sili-
cone to seal the crankshaft keyway.
Thoroughly clean the silicone residue
off of the crankshaft prior to installing
the Vortech harmonic balancer.
D. With adab of silicone on the keyway of the new har-
monic balancer, guide it on the crankshaft and feel for
alignment of the woodruff key and the harmonic bal-
ancer keyway. After the harmonic balancer has been
aligned on the crankshaft, use your harmonic balancer
installation tool to install the new harmonic balancer.
Slowly tighten until the harmonic balancer is seated
on the crankshaft.
NOTE: The use of blue Loctite is recom-
mended for all harmonic balancer and
crank pulley bolts.
4. CRANKSHAFT PULLEY/SUPERCHARGER DRIVE PULLEY, cont'd.
Remove the installation tool and place the supercharger drive
pulley on the front of the harmonic balancer. Feeling for align-
ment, start the 12mm x 1.50 x 65mm center bolt with thick
factory washer and rotate the supercharger drive pulley until
the three bolt holes are aligned. Start the three 8mm x 1.25 x
25mm cap screws with washers, tighten all evenly beginning
with the center bolt (some applications may need two wash-
ers under each 8mm bolt head for thru-bolt clearance to the
engine front cover. Inspect behind balancer when tightening).
Torque the 12mm bolt to 80 ft/Ibs and the 8mm bolts to 25 ft/
108.
Reinstall the inspection cover.
E.
5. FUEL PUMP
Release any pressure from the fuel tank by momentarily loos-
ening the filler cap.
Disconnect the line from the tank to the fuel filter by carefully
removing the white retaining clip or by using a 3/8" springlock
disconnect tool, if equipped.
Connect the fuel pump inlet adapter fitting to the existing fuel
line coming from the fuel tank. Attach the supplied 1/2" inlet
ADAPTER
FITTING 1/2" FUEL LINE
I! (-) GROUND BLACK WIRE
CONNECT TO
(4) RELAY
TERMINAL (87)
Fig. 5-a
₪
hose to the adapter and pump inlet.
NOTE: Due to the various fuel tank configurations and
frame rail lengths it will be necessary to find a
good mounting location near the fuel filter. Do
NOT mount the fuel pump close to exhaust heat
or to the bottom of the cab. The inside or the
outside of the frame rail will work well. Prior to
securing the fuel pump ensure the fuel lines will
not be kinked or pinched and are protected from
sharp edges.
Connect the fuel pump outlet to the filter inlet.
EXISTING FEED LINE
With the fuel pump in a position that FROM TANK
allows the lines to be routed loosely,
secure the fuel pump with the #12
hex screw.
Secure the pump inlet hose using
the supplied #8 clamps. Trim hose
length if necessary. Ensure that NO
kinks or sharp bends are allowed
on pump inlet hose or failure may
result.
Attach the negative pump terminal
to aclean ground. Scrape the ve-
hicle undercoat down to bare metal.
5/16” HOSE
A.
P/N: 4FM020-010
€ 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured
200003 v3.1 4.6/5.4Exped/Nav(4FM v3.1) 6
Fig. 6-a
(+) T-REX FUEL PUMP
(LONGEST RED WIRE)
TO #4 RELAY -
GREEN WIRE WITH
YELLOW STRIPE
12 VOLT (+)
RELAY
Fig. 6-b
NOTE: Double check that all wires are con-
nected to their proper relay lug.
P/N: 4FM020-010
© 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured
2000103 v3.1 4.6/5.4Exped/Nav(4FM v3.1)
6. FUEL PUMP RELAY
A.
Remove the power distribution box from its mount-
ing bracket. Remove the bottom cover and the side
panel exposing the main power lugs, the bottom of
the fuses and relays.
Looking at the underside of the power distribution box,
locate the fuel pump relay (should be labeled #4).
Directly beneath the fuel pump relay, locate the green
wire with yellow stripe.
With the help of an assistant and a test light, check
the green/yellow wire for key-on power, this wire
should show power for approximately two to four sec-
onds with the key in the accessory on position.
From relay terminal #85 route the yellow wire into the
bottom of the power distribution box. Tap into the
green/yellow wire with the provided wire tap. Double
check the wire with a test light to ensure a good con-
nection has been made.
From terminal #30 route the heavy red wire to one of
the main power lugs at the side of the power distribu-
tion box. With the supplied male and female solderless
connectors, install the fuse holder and 20 amp fuse in
this wire and check with a test light to ensure a good
connection has been made. Close the bottom and side своџмо
covers and return the power distribution box to its
original position.
Mark and drill a 1/8” hole above the power distribu-
tion box on the driver's side inner fenderwell, secure
with the #12 x 3/4" sheet metal screw and washer
provided.
Connect the short black wire from relay terminal #86
to a secure ground free from paint.
From terminal #87, route and connect the long red
wire to the (+) side of the fuel pump. Secure with pro-
vided tie wraps.
7. WIRE PREPARATION (4.6 models only)
A. To accommodate the installation of the supercharger
and the relocation of the coil, it will be necessary to
modify the coil and cam trigger loom, extend the ra-
dio ignition interference wire and relocate the spark
plug wire clips.
B. Remove the 90° plastic wire support from the cam
sensor plug, this will allow the wire to be routed tightly
against the face of the main mounting plate at a later
time.
C. Carefully remove approximately 6” of wire wrap from
the loom containing the coil, cam position sensor and
the radio ignition interference capacitor wire. Sepa-
rate the wires and rewrap them individually using black
electrical tape and the provided wire wrap.
D. Cut the radio ignition interference wire approximately
4” from the plug and strip approximately 3/4” of in-
sulation off of the wire. Slip the two 2” pieces of
shrink tube over the exposed wire ends. Solder in the
6” length of red 16 gauge wire.
E. To allow the relocation of the coil, it is necessary to
remove all spark plug wire retaining clips between
the alternator and coil as they will be reinstalled after
the coil has been moved to its new location.
COIL PACK IGNITION
CONNECTOR CAPACITOR
CAM TRIGGER
CONNECTOR
REM OVE PLASTIC
90° WIRE SUPPORT EXTEND WITH 6”
WIRE, SOLDER
AND SHRINK TUBE
UNWRAP “Y” BEND
APPROXIMATELY 6”
Fig. 7-a
P/N: 4FM020-010
€ 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured
2000103 v3.1 4.6/5.4Exped/Nav(4FM v3.1) 8
8A. MAIN MOUNTING PLATE ASSEMBLY AND MOUNTING (4.6L models only)
A. Attach the supplied power steering reservoir/coil
bracket to the main mounting plate using the 1/4-20
x 3/4” bolts, nuts and washers (see photo).
B. Using the supplied 10-24 x 2” bolts and washers, se-
cure the coil and the radio ignition interference ca-
pacitor to the power steering reservoir/coil bracket.
C. To prepare the mounting location for the main mount-
ing plate, remove the three factory stud/bolts previ-
ously used to hold the factory coil bracket to the en-
gine front cover.
D. Remove the front cover bolt located near the lower
driver's side of the alternator mounting flange. In this
location, install the supplied 2.25” idler pulley and idler
spacer using the 10mm x 1.50 x 85mm bolt and
washer. Torque to 40 in/Ibs.
NOTE: n a limited number of 4.6L engines,
the main bracket holes and single idler
pulley hole are 8mm instead of 10mm.
Four 8mm shoulder bolts have been
supplied for these models.
E. Reinstall the accessory belt. Fig. 8A-a
NOTE: The use of blue Loctite is recommended 2.25" IDLER PULLEY
for all idler bolts.
F. With the main mounting plate positioned on the front
cover, start the supplied 8mm-1.25 x 25mm bolt and
the three 10mm -1.50 x 85mm bolts with washers
into the front cover. Torque all bolts evenly.
G. Install the large smooth idler on the inner most idler
stand and the ribbed idler on the outer stand of the
Vortech mounting plate. Secure both with the 12mm
- 1.75 x 20mm bolts and dust shields provided. Torque
to 45 ft/Ibs.
H. Install the cam position sensor plug and secure the
wire to the face of the main mounting plate with the
provided adel clamp. Use the lower coil bracket bolt
to secure clamp.
Fig. 8A-b
SMOOTH IDLER RIBBED IDLER
P/N: 4FM020-010
€ 2003 Vortech Engineering, LLC
9 All Rights Reserved. Intl. Copr. Secured
2000103 v3.1 4.6/5.4Exped/Nav(4FM v3.1)
8A. MAIN MOUNTING PLATE ASSEMBLY AND MOUNTING (4.6L models only) cont'd.
Move the power steering reservoir into the appropri-
ate location on the new power steering reservoir/coil
mounting bracket and secure with the provided 1/4"
hardware.
Secure the power steering reservoir lines away from
the steering shaft with the tie wraps provided.
Reattach the plug wires to the coil and secure with
the previously removed clips.
8B. MAIN MOUNTING BRACKET ASSEMBLY AND MOUNTING (5.4L models only)
ing plate, remove the three 10mm factory stud/bolts
located on the driver side engine front cover.
Reinstall the accessory belt.
NOTE: The use of blue Loctite is recom-
mended for all idler bolts.
Cut and extend the cam sensor wires using the sup-
plied 18GA wires and solderless connectors. Using
tie wraps secure the cam sensor wire as shown in the
photo.
Install the large support bracket onto the engine block
using the 14mm x 2.0 x 35mm bolts, washers, and
spacers. NOTE: The most forward mounting boss
should use the 14mm x 2.0 x 30mm and the smaller
of the two spacers. (Do not tighten the bolts until the
upper part of the support bracket has been mounted.)
With the main mounting bracket positioned on the
front cover, (ensure that the cam sensor wire is not
being pinched by the mounting bracket) start the three
supplied 10mm x 1.5 x 80mm bolts with washers.
Torque all bolts evenly.
Secure the upper portion of the bracket to the previ-
ously installed support bracket using the supplied 1/4"
hardware.
Using the supplied 7/16-14 x 1.5" bolts and dust
shields, secure the three (3) idlers to the main mount-
ing bracket in the configuration shown on page 15.
А. To prepare the mounting location for the main mount-
P/N: 4FM020-010
€ 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured
200003 v3.1 4.6/5.4Exped/Nav(4FM v3.1) 1 0
8B. MAIN MOUNTING BRACKET ASSEMBLY AND MOUNTING (5.4L models only), cont'd.
Fig. 8B-d
P/N: 4FM020-010
© 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured
200CT03 v3.1 4.6/5.4Exped/Nav(4FM v3.1)
Install the supplied support strap between the back of
the main mounting bracket and the boss on top of the
thermostat housing. Secure both ends using the sup-
plied 6mm bolt and washer and the 1/4-20 x 1" flat
allen bolt, washer and lock nut.
Attach the supplied power steering reservoir bracket
to the main mounting bracket using the 1/4-20 bolt
and washers (see photo).
Trim 4" off of the top end of the stock 5/8" supply hose
connecting the reservoir to the pump and reattach.
Extend the stock power steering return hose using
the supplied 3/8" line and hose mender. Secure with
the two supplied #4 hose clamps.
Mount the power steering reservoir onto the new
power steering reservoir bracket and attach with the
provided 1/4" hardware. Using tie wraps, secure the
power steering lines away from the steering shaft.
H.
9. EGR CONTROL MOUNTING AND MAIN MOUNTING PLATE SUPPORT
(4.6L models only)
Fig. 9-b
Using the #10-24 x 1/2” bolts, nuts and washers, re-
mount the EGR controls onto the Vortech mounting
bracket.
Directly beneath the EGR bracket, locate the 6mm
bolt securing the fuel rail. Remove the bolt.
Install the supplied support strap between the intake
manifold and the main mounting plate. Secure both
ends using the factory 6mm fuel rail bolt and the sup-
plied 3/8-16 x 1" hexhead bolt, nut and washer. Make
sure that the strap is not sandwiched in between the |
fuel rail and the manifold. The support must be at-
tached underneath the bolt, and on top of the rail tab.
Improper assembly may cause fuel leakage.
With the two factory 6mm bolts previously used to
mount the EGR controls, remount the new EGR as-
sembly in the original location on the intake manifold
and secure. Reconnect all factory hoses and connec-
tors.
A.
10. FUEL MANAGEMENT UNIT (FMU)
Using a spring lock disconnect tool, disconnect the
fuel return line at the fuel rail.
Connect the FMU inlet hose to the fuel rail. Route the
fuel line to the 90? brass fitting on the FMU.
Position FMU against the upper firewall directly un-
der the plastic wire harness cover as shown. Mark
and drill two #30 holes on the firewall to mount the
FMU. Secure with the 48 sheet metal screws pro-
vided.
Connect the FMU outlet hose to the fuel line that re-
turns to the tank. Route the fuel line to the straight
brass fitting on the FMU.
Secure the fuel lines away from abrasion and exhaust
A.
C.
P/N: 4FM020-010
€ 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured
200003 v3.1 4.6/5.4Exped/Nav(4FM v3.1) 1 2
FUEL
MANAGEMENT
UNIT (FMU)
FACTORY
QUICK-
DISCONNECT
FITTING
FUEL RETURN LINE
P/N: 4FM020-010
© 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured
2000103 v3.1 4.6/5.4Exped/Nav(4FM v3.1)
FILTER
|
VACUUM LINE
[г
FACTORY
SPRINGLOCK
CONNECTOR
FUEL FEED LINE
| ; FACTORY VACUUM
heat with the provided tie wraps. CONNECTION
Е Tap into the factory fuel regula- F
tor vacuum line with the supplied
5/32" hose and TEE. Route the
new hose to the fitting on top of
the FMU (see drawing). FACTORY
REGULATOR
Fig. 10-b
10.1 FUEL MANAGEMENT UNIT
RECALIBRATION (2003 5.4L Only)
A. Remove the six allen-head screws on top of the fuel
management unit (FMU). (See Fig. 7/1-a.)
WARNING: Do not remove the four screws holding
the valve body. Once taken apart, the
vlave would have to be replacedl.
B. Remove the diaphram and 7:1 disk (2.038' O.D.) and
ring from inside of the FMU.
C. Install the replacement 8:1 ring (with notched part
facing down) around the four screws inside the FMU.
(The 8:1 components are larger in diameter that their
7:1 counterparts.) Place the 8:1 disk (2.22' O.D.) in
side the ring on top of the piston.
D. Install the new diaphram and carefully line up the holes
to the body.
E. Reinstall the FMU cover with the six allen-head screws.
Do not overtighten the screws. The correct torque is
24 in/Ib (2 ft/Ib.).
11. IDLE AIR CONTROL RESONATOR AND CRANKCASE VENT HOSE REROUTING
* 4.6L ONLY
* 4.6L ONLY
Fig. 12-a
Attach the supplied 3/4" x 90? rubber elbow to the
idle control motor near the throttle body. (See Fig.
11-a.) Insert the factory idle control resonator into |
the elbow and locate underneath the discharge tube.
Connect the supplied 3/4" x 28" hose to the idle con-
trol resonator and route the remaining end to the new
air inlet location. See step 14.
Remove the 90? rubber elbow from the factory valve
cover vent on the left side of the engine. Attach the
short leg of the supplied 5/8" x 90? x 24" hose to the
valve cover and route the long straight end over to
the brass fitting on the supercharger inlet elbow. Trim
hose length, if necessary. See step 14.
* А.
12. SUPERCHARGER MOUNTING
Attach the oil drain hose to the oil drain fitting on the
bottom of the supercharger and secure with the pro-
vided #8 hose clamp.
Guide the oil drain hose over the driver's side valve
cover while placing the supercharger in the appropri-
ate location. (See Fig. 12-a.)
NOTE: The oil drain line must be routed in а
downward sloping fashion with no kinks
or restrictions.
With the oil drain hose properly routed downward,
start the five 3/8-16 x 2-1/2” counter sink bolts and
tighten evenly.
5.4L ONLY - Once the oil drain hose has been prop-
erly routed downward, use the five 3/8-16 bolts and
washers, start and tighten evenly.
Route the oil drain hose around the side of the power
steering pump and to the oil drain fitting on the oil
pan.
NOTE: Do NOT use any type of sealant on the
oil feed fittings. It may become dis-
lodged and clog the oil feed orifice,
causing premature failure of the super-
charger.
Using a few drops of engine oil on the fitting threads,
install the 1/8" NPT x -4 x 90? fitting into the super-
charger oil feed. Rotate the fitting toward the front of
the vehicle. Usea 1/2" wrench to hold the supercharger
oil feed while tightening the brass 90? fitting.
Two oil feed hoses have been supplied. The 36" long
hose is for use on the 2WD models that are not
equipped with an engine oil cooler. The 62" hose is
for use on 4WD oil cooler equipped models. Connect
the proper length oil feed line to the vehicle and se-
cure both ends. Make sure that no dirt or debris en-
ters the oil hose while routing to the feed fittings.
A.
*
B.
P/N: 4FM020-010
€ 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured
200003 v3.1 4.6/5.4Exped/Nav(4FM v3.1) 1 4
VORTECH
SMOOTH VORTECH
RIBBED
IDLER PULLEY
NOTE: SUPERCHARGER
BELT IS ON OUTSIDE
(FORWARD) OF ACCESSORY
BELT
* 4.6L ONLY
P/N: 4FM020-010
€ 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured
2000103 v3.1 4.6/5.4Exped/Nav(4FM v3.1)
2.25 PULLEY
12. SUPERCHARGER MOUNTING, cont'd.
G. Secure the oil feed line and oil drain line away from heat
and abrasion with the provided tie wraps.
Mount the belt tensioner plate onto the face of the super-
charger with the three 12mm x 1.75 x 20mm bolts and
washers. The thin head bolt must be installed nearest the
idler pulley pilot.
5.4L ONLY - Mount the automatic tensioner to the mount-
ing bracket using the 3/8- 16 x 3.25" bolt and washer.
Route the supplied supercharger drive belt around the su-
percharger crank pulley, the inner and outer idlers and to
the supercharger.
Install the smooth tensioner pulley to the tensioner plate
pilot using the 12mm x 1.75 x 20mm bolt provided.
With a 1/2" drive breaker bar and a 3" extension, rotate the
tensioner plate to tighten the belt. Tighten the three 12mm
fasteners. Use thin 18mm wrench to tighten the bolt head
nearest to the idler pulley.
"H.
*K
*NOTE: The supercharger drive belt should have ap-
proximately 1" of deflection and will need to
be retightened between 250 to 400 miles.
5.4L ONLY - Using a 1/2" drive breaker bar, rotate the
tensioner clockwise and align belt. Release tensioner to
tighten belt.
Connect the oil drain hose down to the oil pan tube previ-
ously installed. Trim hose length if necessary and secure
with a #8 clamp. Make sure drain hose runs downhill con-
tinuously with no kinks or dips. Support fitting in oil pan
with a wrench while tightening the drain tube fitting. Make
sure the tube is angled up, but maintaining clearance from
the drive belt (see photo in step 3).
ALTERNATOR
WATER
PUMP
HARMONIC
BALANCER/
CRANK PULLEY
Fig. 12-c
4.6L MODELS ONLY
AIR
CONDITIONER
12. SUPERCHARGER MOUNTING, cont'd.
5.4L MODELS ONLY
SPRING TENSIONER
SMOOTH IDLE 7 `
HARM We
BALANCER/ |
CRANK PULLEY |
Fig. 12-d
P/N: 4FM020-010
COOLANT
RESERVOIR
FRONT
© 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured
200CT03 v3.1 4.6/5.4Exped/Nav(4FM v3.1)
13. MASS AIR FLOW SENSOR REMOVAL, MOUNTING AND ASSEMBLY
INNER FENDERWELL
TOP VIEW
Fig. 13-a
A. Separate the mass air flow sensor
from the air inlet canister.
B. Assemble the mass air sensor and
the mass air sensor mounting
bracket with the 1/4-20 x 3/4" bolts,
nuts and washers. Mount the air
filter to the bracket and secure the
#60 clamp.
C. Using the factory air inlet filter can- CRUISE
ister mounting location, secure the CONTROL
mass air bracket with the 5/16-18
א 1-1/2” bolts, nuts and washers;
use the large 5/16 fender washers
on the bottom of the factory rub-
ber grommets.
D. Connect the 90° plastic elbow
equipped with the 3/4” barb 90°,
to the 3-1/2 silicone sleeve. Secure
with the #56 hose clamps.
E. 5.4 Models only - Wire/Install the
supplied MAF Voltage Limiter As-
sembly. Use the instruction sheet
supplied in the MAF Voltage Lim-
iter Assembly.
14. AIR INLET/BYPASS ASSEMBLY
A. Place the 3-1/2” silicone sleeve and the #56 hose
clamps onto the supercharger inlet. Install the 90°
plastic inlet eloow. Secure the #56 hose clamps. In-
sert the factory air temperature sensor into the rub-
ber grommet located on the inlet elbow and attach
the connector.
B. Attach the supplied 1” א 5" hose 1" x 9" hose -4.6L,
5.4L and #16 hose clamp to the 1” plastic 90° fitting
installed on the inlet elbow. Secure clamp.
SENSOR
4.6L model shown
Fig. 14-c
4.6L MODELS ONLY
(see photo above)
Fig. 14-d
5.4L MODELS ONLY
Fig. 14-e
14. AIR INLET/BYPASS ASSEMBLY, cont'd.
C. Install the bypass valve and #16 hose clamp on the
end of the 1" x 5" ћозе - 4.6L, 1" x 9" hose - 5.4L. On
the 4.6L, bypass nipple should be pointing toward the
driver's seat. On the 5.4L, bypass nipple should be
pointing downward.
D. Using the supplied 5/32" TEE and hose, splice the by-
pass nipple into the previously installed vacuum hose
attached to the FMU lid.
E. Place the 1" x 7"-4.6L, 1" x 2.5" - 5.4L piece of hose
and #16 hose clamps on the bypass valve. The hose
will be connected to the discharge in the next step.
F. Connect the two 90? plastic elbows with the 3-1/2"
flex hose and secure with #56 hose clamps.
G. Install the idle air and crankcase vent hoses to the air
inlet elbow.
5/8” 90° BARB
DRIVER’S SIDE
VALVE COVER
CRANK VENT
_ 1” x 5" HOSE
1” x7” HOSE
=й
>» ` TEMP SENSOR
FLEX
DISCHARGE
pisoi SUPERCHARGER HOSE
3/4” 90° BARB
TO IDLE AIR
RESONATOR
3/4” 90° BARB
TO IDLE AIR
RESONATOR
5/8” 90° BARB /
DRIVERS SIDE VALVE |.
COVER CRANK VENT
1" X 90°
PLASTIC
BYPASS HOSE BARB
VALVE WITH
” ” ~
1" x 2.5" HOSE AIR INTAKE
TEMP SENSOR
SUPERCHARGER
—-—— = BOTTOM VIEW E
N
TTT)
P/N: 4FM020-010
€ 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured
2000103 v3.1 4.6/5.4Exped/Nav(4FM v3.1) 1 8
erly installed may cause FAILURE OF MA-
JOR COMPONENTS.
Test drive the vehicle.
The supercharger belt stretches initially and
will require adjustment in 250 to 400 miles.
Read the STREET SUPERCHARGER SYS-
TEM OWNER'S MANUAL AND RETURN
THE WARRANTY REGISTRATION FORM
within thirty (30) days of purchasing your
supercharger system to qualify.
* 4.6L ONLY
P/N: 4FM020-010
© 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured
2000103 v3.1 4.6/5.4Exped/Nav(4FM v3.1)
15. DISCHARGE
Install the 3" silicone sleeve and the #48 hose clamps
on the throttle body.
Slide the 2-3/4” silicone sleeve and the #44 hose
clamps onto the discharge tube.
Install the discharge tube on the throttle body side.
Rotate the supercharger side into position and center
the silicone sleeve. Secure with #48 and #44 hose
clamps.
Connect the 1” bypass hose to the bung on the back-
side of the discharge tube and secure using a #16
hose clamp.
Inspect all ducts and hoses to ensure they are secure
and that all hose clamps are properly tightened.
Remove the factory PCV valve from the right side valve
cover and install the supplied PCV in its place.
WARNING: Do not attempt to operate the vehicle until
ALL components are installed and ALL
operations are completed including the
final check.
A.
FINAL CHECK
NOTE: 99-03 Models Only - Once the ECM is re-
ceived back from Vortech with the ECM mod-
ule installed, reinstall the ECM into the ve-
hicle. In some cases, the extra height of the
ECM module will not allow the use of the fac-
tory hold-down bracket. Reconnect the fac-
tory Mes and reinstall the factory kick
panel.
Reconnect the battery.
If your vehicle has gone over 20,000 miles since its
last spark plug change, you will need to change the
spark plugs now before test driving the vehicle.
Check all fittings, nuts, bolts and clamps for tight-
ness. Pay particular attention to oil and fuel lines
around moving parts, sharp edges and exhaust sys-
tem parts. Make sure all wires and lines are properly
secured with clamps or tie wraps.
Check all fluid levels, making sure that your tank(s)
is/are filled with 92 octane or higher fuel before com-
mencing test drive.
Start engine and allow to idle a few minutes, then shut
off.
Recheck to be sure that no hoses, wires, etc. are near
exhaust headers or moving parts and for signs of any
fluid leakage.
PLEASE TAKE SPECIAL NOTE: Operating the vehicle
without ALL the subassemblies completely and prop-
16.
ENGINEERING, LLC
1650 PACIFIC AVENUE + CHANNEL ISLANDS, CA 93033-9901 • (805) 247-0226
FAX (805) 247-0669 • www.vortechsuperchargers.com * M-F 8:00 AM - 4:30 PM PST
P/N: 4FM020-010
€ 2003 Vortech Engineering, LLC
All Rights Reserved. Intl. Copr. Secured
2000103 v3.1 4.6/5.4Exped/Nav(4FM v3.1)