Document text
O0 O0 TDA10019 9 0
INTEGRATED CIRCUITS
DATA SHEET
TDA1001B
TDA1001BT
Interference and noise suppression
circuit for FM receivers
Product specification December 1982
File under Integrated Circuits, IC01
Philips PHILIPS
Semiconductors pD H l L
Philips Semiconductors Product specification
Interference and noise suppression TDA1001B
circuit for FM receivers TDA1001BT
GENERAL DESCRIPTION
The TDA1001B is a monolithic integrated circuit for suppressing interference and noise in FM mono and stereo receivers.
Features
e Active low-pass and high-pass filters
e Interference pulse detector with adjustable and controllable response sensitivity
e Noise detector designed for FM i.f. amplifiers with ratio detectors or quadrature detectors
e Schmitt trigger for generating an interference suppression pulse
e Active pilot tone generation (19 kHz)
e Internal voltage stabilization
QUICK REFERENCE DATA
Supply voltage (pin 9) Vp typ. 12 V
Supply current (pin 9) Ip typ. 14 mA
A.F. input signal handling (pin 1)
(peak-to-peak value) Vi(p-p) typ. 1 V
Input resistance (pin 1) Ri min. 35 kQ
Voltage gain (V1-16/V6-16) Gy typ. 0,5 dB
Total harmonic distortion THD typ. 0,25 %
Bandwidth B typ. 70 kHz
Suppression pulse threshold voltage
(peak value); R73 = 0 Viitnom typ. 19 mV
Suppression pulse duration ts typ. 27 us
Supply voltage range (pin 9) Vp 7,5 to 16 V
Operating ambient temperature range Tamb -30 to +80 °C
PACKAGE OUTLINE
TDA1001B: 16-lead DIL; plastic (SOT38); SOT38-1; 1996 September 06.
TDA1001BT: 16-lead mini-pack; plastic (S016; SOT109A); SOT116-1; 1996 September 06.
December 1982 2
Philips Semiconductors
Interference and noise suppression circuit
for FM receivers
Product specification
TDA1001B
TDA1001BT
HIGH - PASS
FILTER
HIGH - PASS A.G.C.
AMPLIFIER IRER
TDA1001B NOISE
DETECTOR
INPUT STAGE
{EMITTER —
FOLLOWER}
LOW -PASS
AMPLIFIER
2
j LOW-PASS
FILTER
INTERFERENCE
PULSE
DETECTOR
INTERFERENCE
SUPPRESSION
PULSE STAGE i
a.f. output
Fig.1 Block diagram.
SUPPRESSION
PULSE
GENERATOR
SUPPLY
VOLTAGE
STABILIZER
19 kHz
PILOT- TONE
GENERATOR
p 19 kHz
FILTER
7Z87171
December 1982 3
Philips Semiconductors
Interference and noise suppression circuit
for FM receivers
RATINGS
Product specification
Limiting values in accordance with the Absolute Maximum System (IEC 134)
Supply voltage (pin 9)
Input voltage (pin 1)
Output current (pin 6)
Total power dissipation
Storage temperature range
Operating ambient temperature range
TDA1001B
TDA1001BT
Vp max. 18 V
Vi-16 max. Vp V
Ig max. 1 mA
-l6 max. 15 mA
see derating curves Fig.2
Tstg —65 to +150 °C
Tamb —30 to +80 °C
7287172
0 50 100 5 150
Tamb (°C)
in plastic DIL (SOT-38) package (TDA1001B).
------ in plastic mini-pack (SO-16; SOT-109A) package (TDA1001BT); mounted on a ceramic substrate of 50 x 15 x 0,7 mm.
Fig.2 Power derating curves.
December 1982
Philips Semiconductors Product specification
Interference and noise suppression circuit TDA1001B
for FM receivers TDA1001BT
CHARACTERISTICS
Vp= 12 V; Tamb = 25 °C; measured in Fig.4; unless otherwise specified
PARAMETER SYMBOL MIN. TYP. MAX. UNIT
Input stage
Input impedance (pin 1)
f = 40 kHz |Z z 45 = kQ
Input resistance (pin 1)
with pin 2 not connected Rix - 600 — kQ
Input bias current (pin 1)
V1-16 = 4,8 V lit = 6 15 uA
Output resistance (pin 2)
unloaded Ro2 low-ohmic
Internal emitter resistance R216 — 5,6 — kQ
Low-pass amplifier
Input resistance (pin 3) Ris 10 = = MQ
Input bias current (pin 3) lig = = 7 uA
Output resistance (pin 4) Ro4 = = 5 Q
Voltage gain (V4/V3) Gya/3 = 1,1 —
Suppression pulse stage
Input offset current at pin 5
during the suppression time ts lio5 - 50 200 nA
Output stage
Output resistance (pin 6) Rog low-ohmic
Internal emitter resistance Re-16 - 6 - kQ
Current gain (I5/lg) Gis/6 - 85 - dB
Pilot tone generation (19 kHz)
Input impedance (pin 8) |Zigl - - 1 Q
Output impedance (pin 7)
pin 8 open | Zo7! 150 = = kQ
Output bias current (pin 7) lo7 0,7 1 1,3 mA
Current gain (I7/lg) Gi7/8 — 3 —
High-pass amplifier
Input resistance (pin 15) Riis 10 - - MQ
Input bias current (pin 15) lit5 - - 7 uA
Output resistance (pin 14) Ro14 - - 5 Q
Voltage gain (V14⁄15) Gv14/15 = 1,4 =
December 1982 5
Philips Semiconductors
Product specification
Interference and noise suppression circuit TDA1001B
for FM receivers TDA1001BT
PARAMETER SYMBOL MIN. TYP. MAX. UNIT
A.G.C. amplifier; interference and noise detectors
Internal resistance (pins 13 and 14) Ri3-14 1,5 2,0 2,5 kQ
Operational threshold voltage
(uncontrolled); peak value (pin 14)
of the interference pulse detector + Vi 4int m - 15 - mV
of the noise detector + Vian m — 6,5 — mV
Output voltage (peak value; pin 11) V11-16M 5,2 5,8 6,4 V
Output control current (pin 12)
(peak value) liom 150 200 250 uA
Output bias current (pin 12) l012 - 2,5 6 uA
Input threshold voltage for onset of control (pin 12) Vi29 360 425 500 mV
(Vitro+ 3 dB) or: r 0,66Vge |- mV
Suppression pulse generation (Schmitt trigger)
Switching threshold (pin 11)
1: gate disabled V11-16 — 3,2 — V
2: gate enabled V11-16 — 2,0 — V
Switching hysteresis AV11-16 — 1,2 — V
Input offset current (pin 11) lio11 = - 100 nA
Output current (pin 10)
gate disabled; peak value loom 0,6 1 1,4 mA
Reverse output current (pin 10) IR10 - - 2 uA
Sensitivity (pin 10) V10-16 2,5 - - V
December 1982 6
Philips Semiconductors
Product specification
Interference and noise suppression circuit TDA1001B
for FM receivers TDA1001BT
APPLICATION INFORMATION
Vp= 12 V; Tamb = 25 °C; f = 1 kHz; measured in Fig.4; unless otherwise specified
PARAMETER SYMBOL MIN. TYP. MAX. UNIT
Supply voltage range (pin 9) Vp 7,5 12 16 V
Quiescent supply current (pin 9) Ip 10 14 18 mA
Signal path
D.C. input voltage (pin 1) Vi-16 - 4,5 - V
Input impedance (pin 1); f = 40 kHz |Zit| 35 - - kQ
D.C. output voltage (pin 6) V6-16 2,4 2,8 - V
Output resistance (pin 6) Rog low-ohmic
Voltage gain (V¢/V1) Gvet 0 0,5 1 dB
-3 dB point of low-pass filter f(-3aB) = 70 = kHz
Sensitivity for THD < 0,5%
(peak-to-peak value) Vi(p-p) 1,2 1,8 = V
Residual interference pulse after suppression
(see Fig.3); pin 7 to ground;
Vict = 100mV; (peak-to-peak value) V6-16(p-p) - = 3 mV
Interference suppression at R13 = 0;
notes 5 and 6; Virms) = 30 mV; f = 19 kHz
(sinewave); Victrm = 60 mV; fr = 400 Hz Clint 20 30 - dB
Interference processing
Input signal at pin 1; output signal at pin 10
Suppression pulse threshold voltage; control
function OFF (pin 9 connected to pin 12);
r.m.s. value; note 1
measured with sinewave input signal
f = 120 kHz; -Vig.9>1V
at R13 =0Q9 Vittyrms 8 11 14 mV
at R13 = 2,7 kQ Vittr)rms 18 28,5 40 mV
voltage difference for safe triggering/
non-triggering (r.m.s. value) AVirms) - 1 - mV
measured with interference pulses
f = 400 Hz (see Fig.3); peak value
at R13 =0Q Vittgm E 19 — mV
at R13 = 2,7 KQ Vittnm = 45 — mV
Suppression pulse duration (note 2) ts 24 27 30 us
December 1982 7
Philips Semiconductors Product specification
Interference and noise suppression circuit TDA1001B
for FM receivers TDA1001BT
PARAMETER SYMBOL MIN. TYP. MAX. UNIT
Noise threshold feedback control (notes 1 and 3)
Noise input voltage (r.m.s. value) f = 120 kHz
sinewave for V12-9 = 300 mV
at R13 =00 Vni(rms) 2,3 3,3 4,3 mV
at R13 = 2,7 KQ Vhi(rms) — 8,2 — mV
for V12-9 = 425 mV (Vito +3 dB)
at R13 =0Q Vni(rms) = 7,3 — mV
at R13 = 2,7 KQ Vhi(rms) = 16,5 — mV
for V12-9 = 560 mV (Vito +20 dB)
at R13 =0 Q Vni(rms) 33 45 57 mV
at R13 = 2,7 KQ Vhi(rms) — 107 — mV
Amplification control voltage by interference intensity
(note 4)
Vi«rms) = 50 mV; f = 19 kHz;
Vitym = 300 mV; r.m.s. value
at repetition frequency f,= 1 kHz Vo6(rms) 49 — 56 mV
at repetition frequency fr = 16 kHz Vo6(rms) 45 — 65 mV
Notes to application information
1. The interference suppression and noise feedback control thresholds can be determined by R13 or a capacitive
voltage divider at the input of the high-pass filter and they are defined by the following formulae:
Vitr = (1 + R13/Rs) x Vitro in which Rs =2 kQ;
Vni = (1 + R13/Rs) x Vnio in which Rg = 2 kQ.
2. The suppression pulse duration is determined by C11 = 2,2 nF and R11 = 6,8 KQ.
3. The characteristic of the noise feedback control is determined by R12 (and R10).
4. The feedback control of the interference suppression threshold at higher repetition frequencies is determined by R10
(and R12).
5. The 19 kHz generator can be adjusted with R7-16 (and R7-8). Adjustment is not required if components with small
tolerances are used e.g. AR < 1% and AC < 2%.
6. Measuring conditions:
The peak output noise voltage (Vno m, CCITT filter) shall be measured at the output with a de-emphazing time T = 50
us (R = 5 kQ, C = 10 nF); the reference value of 0 dB is Vo int with the 19 kHz generator short-circuited (pin 7
grounded).
December 1982 8
Philips Semiconductors Product specification
Interference and noise suppression circuit TDA1001B
for FM receivers TDA1001BT
SQUARE ~- WAVE
INPUT VOLTAGE
> [ta
o ay
SUPPRESSION Y10-9 fl —_ t= 27
|]
PULSE (TRIGGER) (V) L | i
OUTPUT -1,5 + lus
over-shoot of the
re low- pass filter
1
v
OUTPUT ET 0
VOLTAGE (mv)
offset voltage
and drift
voltage
time (us)
Fig.3 Measuring signal for interference suppression; at the input (pin 1) a square-wave is applied with a duration
of tr = 10 us and with rise and fall times t; = tt = 10 ns.
HIGH -PASS FILTER
V
s
430k 4.7 PF ae (10 to 16V)
f- of, p7 H
91k2 5
330pF|330pF 330pF 330pF a a pres doin 41 |
IHH 6,8k2 =
c11
ia Ka ea | 22k2 10 nF 22nF 220nF
i 4 15k2 1,5k2
to Vp TDA1001B
120 |
V: +
t
ing)
4,7 pF
82k2 47kQ 4,7k2 =a —
CO OR ED 4
ch, 3,9,
g 680 680 1,2 68 nF! | 2,1kQ
pF pale nF pF J i I
d d d d 7Z87170
Vo
LOW- PASS FILTER 19 kHz FILTER
Fig.4 Application circuit diagram.
December 1982 9
Philips Semiconductors Product specification
Interference and noise suppression circuit TDA1001B
for FM receivers TDA1001BT
PACKAGE OUTLINES
DIP 16: plastic dual in-line package; 16 leads (300 mil); long body SOT38-1
a seating plane
fall
PL
fi i fi
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
A A1 A2 (1) (1)
UNIT max. min. | max. by D E
21.8 6.48
21.4 6.20
0.86 0.26
0.84 0.24
mm 4.7 0.51 3.7
inches 0.19 0.15
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
REFERENCES
IEC
JEDEC
EIAJ
EUROPEAN
PROJECTION
ISSUE DATE
SOT38-1
050G09
MO-001AE
in
92-40-02
95-01-19
December 1982
10
Philips Semiconductors Product specification
Interference and noise suppression circuit TDA1001B
for FM receivers TDA1001BT
S016: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1
‘— 0
f
| Lp
a— |]
detail X
2.5
L ı l ıı ı
1
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
UNIT f A2 c pM | eM) He
0.25 | 10.0 | 4.0 6.2
0.19 | 9.8 3.8 : 5.8
0.0098] 0.39 | 0.16
0.0075] 0.38 | 0.15
inches
Note
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
OUTLINE
VERSION
REFERENCES
EUROPEAN
IEC
JEDEC
EIAJ
PROJECTION
ISSUE DATE
SOT109-1
076E07S
MS-012AC
ay
94-08-43-
95-01-23
December 1982
11
Philips Semiconductors
Interference and noise suppression circuit
for FM receivers
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
DIP
SOLDERING BY DIPPING OR BY WAVE
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (T stg max). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
REPAIRING SOLDERED JOINTS
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.
SO
REFLOW SOLDERING
Reflow soldering techniques are suitable for all SO
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
December 1982
Product specification
TDA1001B
TDA1001BT
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250 °C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45 °C.
WAVE SOLDERING
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
e A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
e The longitudinal axis of the package footprint must be
parallel to the solder flow.
e The package footprint must incorporate solder thieves at
the downstream end.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 °C within
6 seconds. Typical dwell time is 4 seconds at 250 °C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
REPAIRING SOLDERED JOINTS
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300 °C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320 °C.
Philips Semiconductors Product specification
Interference and noise suppression circuit TDA1001B
for FM receivers TDA1001BT
DEFINITIONS
Data sheet status
Objective specification This data sheet contains target or goal specifications for product development.
Preliminary specification This data sheet contains preliminary data; supplementary data may be published later.
Product specification This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
December 1982 13