Document text
FM9-6
MUNITIONS SUPPORT IN
THE THEATER OF
OPERATIONS
HEADQUARTERS, DEPARTMENT OF THE ARMY
DISTRIBUTION RESTRICTION: Approved for public release; distribution is unlimited.
*FM 9-6
Field Manual Headquarters
No. 9-6 Department of the Army
Washington, DC, 20 March 1998
MUNITIONS SUPPORT
IN THE
THEATER OF OPERATIONS
Table of Contents
PREFACE iii
CHAPTER 1 INTRODUCTION TO MUNITIONS SUPPORT 1-1
Purpose and Scope 1-1
Munitions Support Mission 1-1
Supported Units 1-2
Support Environment 1-2
CSS Characteristics 1-2
Planning Guidance 1-4
Munitions Strategic, Operational, and Tactical Logistic Levels 1-4
Support Structures 1-7
CHAPTER 2 MUNITIONS SUPPORT STRUCTURE 2-1
Purpose and Scope 2-1
Ammunition Surge Support 2-1
Support Structure Overview 2-1
Ammunition Support Activities 2-1
Ammunition Units 2-1
Ammunition Support Team 2-15
Munitions Flow in the Theater 2-17
Aerial Resupply 2-18
Command and Support Relationships 2-19
Functional Responsibilities 2-19
CHAPTER 3 MUNITIONS PLANNING AND EXECUTION 3-1
Purpose and Scope 3-1
Conventional Ammunition Allocations 3-1
Logistics Preparation of the Theater 3-3
CHAPTER 4 RETROGRADE OPERATIONS 4-1
Purpose and Scope 4-1
Redeployment and Retrograde 4-1
Destruction of Ammunition 4-3
Ammunition Maintenance 4-4
i DISTRIBUTION RESTRICTION: Approved for public release; distribution is unlimited.
*This publication supersedes FM 9-6, 1 September 1989.
Physical Security 4-5
Transportation and Storage 4-6
CHAPTER 5 EXPLOSIVE ORDNANCE DISPOSAL SUPPORT STRUCTURE 5-1
Overview 5-1
EODRole 5-1
EOD Incidents 5-2
Control Procedures 5-3
Transition to War 5-3
Support Structure and Operations 5-3
Host Nation Interface 5-7
Communications 5-7
CHAPTER 6 THE ENVIRONMENT, SAFETY, RISK MANAGEMENT,
AND MAINTENANCE AND SURVEILLANCE OPERATIONS 6-1
SECTION I THE ENVIRONMENT 6-1
Environmental Policy and Goals 6-1
Stewardship in the Operational Environment 6-2
SECTION II SAFETY 6-4
Responsibilities 6-4
Standing Operating Procedures 6-5
Accident Reporting 6-5
SECTION III RISK ASSESSMENT AND MANAGEMENT 6-6
Integrating Assessment Techniques 6-6
Five-Step Process 6-6
SECTION IV MAINTENANCE AND SURVEILLANCE OPERATIONS 6-6
Maintenance Operations 6-6
Surveillance 6-7
Surveillance Records and Reports 6-10
Destruction Plan 6-11
Unserviceable Ammunition Storage 6-12
Suspended Ammunition Storage 6-12
Captured Enemy Ammunition Storage 6-13
APPENDIX STANDARD ARMY AMMUNITION
SYSTEM-MODERNIZATION (SAAS-MOD) A-1
GLOSSARY Glossary-1
REFERENCES References-1
AUTHENTICATION Authentication
ii DISTRIBUTION RESTRICTION: Approved for public release; distribution is unlimited.
*This publication supersedes FM 9-6, 1 September 1989.
FM 9-6 PREFACE
PREFACE This FM prescribes doctrine for munitions support. It explains in general terms how
munitions units operate and how they interact to provide munitions to the user. It is the basis for
munitions doctrine, materiel, training, and organizational development. This manual addresses munitions
unit missions, operations, and interactions between the various levels of munitions support.
FM 9-6 explains to combat arms, combat support (CS), and combat service support (CSS) commanders
and their staffs how and where they receive munitions support. It establishes guidelines and procedures
for munitions unit commanders and their staffs operating the munitions support structure.
Also, this manual introduces two very important doctrinal changes. First, it incorporates the
maneuver-oriented ammunition distribution system, palletized load system (MOADS-PLS) into the
ammunition support structure as Army doctrine. This allows for the extensive use of PLS for the
distribution of ammunition. Second is the modular ammunition platoon concept. There are two types of
modular platoons: heavy lift and medium lift. The heavy lift platoon (HLP) is best suited for port, theater
storage area (TSA), and corps storage area (CSA) operations. Medium lift platoons (MLPs) operate in
TSAs and CSAs when needed and are designed to operate ammunition supply points (ASPs). These
platoons are capable of deploying and operating independently from their company headquarters, but
require external support for sustainment. They allow the Army to effectively take advantage of
technology and the PLS. The PLS incorporates strategic and mission configured loads (MCLs). These
palletized loads are capable of being shipped to TSAs, CSAs, and ASPs. The type and number of
platoons deployed is based on mission, enemy, troops, terrain and weather, and time available (METT-T)
and the commander' s intent. Modular units provide a flexible design tailorable to the theater
commander's intent. They give the theater commander the capability to expand and contract the
ammunition supply capability when and where needed to meet operational requirements.
This publication implements the following standardization agreements (STANAGs):
STANAG 2034 . Land Forces Procedures for Allied Supply Transactions, Edition 4. 20 December 1982.
STANAG 2135 . Procedures for Emergency Logistics Assistance, Edition 3. 12 February 1982.
STANAG 2827 . Materials Handling in the Field, Edition 2. 12 February 1980.
STANAG 2829 . Materials Handling Equipment, Edition 2. 20 March 1978.
STANAG 2834 . The Operation of the Explosive Ordnance Disposal Technical Information Center
(EODTIC), Edition 2. 26 March 1990.
STANAG 2928 . Land Forces Ammunition Interchangeability Catalogue in Wartime, Edition 3. 9 June
1995.
STANAG 2961 . Classes of Supply of NATO Land Forces, Edition 1. 11 December 1984.
The proponent for this publication is Headquarters, United States Army Training and Doctrine Command
FM 9-6 PREFACE
(HQ, USATRADOC). Send comments and recommendations on DA Form 2028 (or in 2028 format)
directly to Commander, USACASCOM&FL, Training Directorate, ATTN: ATCL-AO, 801 Lee Avenue,
Fort Lee, VA 23801-1713.
Unless this publication states otherwise, masculine nouns and pronouns do not refer exclusively to men.
IV
FM 9-6 CHAPTER 1
CHAPTER 1
INTRODUCTION TO MUNITIONS SUPPORT
"A soldier can survive on the battlefield for months without
mail, weeks without food, days without water, minutes
without air, but not one second without ammo!"
(Author Unknown)
PURPOSE AND SCOPE
Munitions is the dominant factor in determining the outcome of combat or stabiHty and support operations
(SASO). It is a critical component of fire and maneuver operations performed by the force projection Army.
Munitions provide the means to defeat as well as destroy the enemy. They give the force the ability to block,
screen, or protect itself.
The limited quantity of our modem munitions and weapons systems requires that munitions are managed to
ensure availability and enhance combat readiness. In the future, most major military operations will be joint or
coalition and based on unexpected contingencies. These operations will require the munitions logistic system
to be modular, tailorable, easily deployed, and flexible.
This chapter introduces the munitions support structure and its mission. It addresses the following topics:
q Supported units,
q Support environment,
q Munitions support considerations,
q Sustainment imperatives.
q Munitions strategic, operational, and tactical interfaces,
q Transportation interfaces.
MUNITIONS SUPPORT MISSION
Our national security needs form the basis of our national military strategy. We must support the four basic
demands that are fulfilled by the military. They are:
q Guarantee strategic deterrence and defense.
q Exercise a forward presence in vital areas of the world.
q Respond effectively to a crisis.
q Retain the capacity to reconstitute forces.
The Army's ability to react and sustain the battle improves the chances of conduct-ing a successful operation.
The munitions soldier's mission is to ensure munitions arrive in the hands of the warfighter in the right
quantities and proper types at the decisive time and place. Munitions logistic plans must mesh the tactical level
1-1
FM 9-6 CHAPTER 1
commander's plan to the operational and strategic plans. This helps ensure timely support and sustains the
operation.
Commanders, with advice from logis-ticians, tailor support packages to meet theater requirements for a variety
of strategic contingency plans. The use of modular ammunition units increases our ability to meet theater
munitions requirements. Modular units will be deployed based on operational needs and will help ease
strategic lift requirements.
The Army's ability to meet its force projection requirements calls for highly mobile, multifunctional
organizations capable of projecting munitions support anywhere in the world. The measure of success is the
ability to accomplish the following effectively and efficiently:
Provide munitions to operational and tactical commanders.
Support current and future gener-ations of combat power anywhere in the world.
Sustain maneuver forces in a wide variety of mission profiles.
Support the tenets of Army oper-ations doctrine.
Retrograde munitions to the conti-nental United States (CONUS) or other theaters of operations.
SUPPORTED UNITS
Every unit on the battlefield requires munitions. Providing sufficient types and quantities at the right place on
time is critical to the success of combat operations and SASO. When the Army fights as part of a joint,
multinational, or combined force, US Army munitions units may support other US services and allied forces.
SUPPORT ENVIRONMENT
Ammunition units must push munitions forward on the battlefield. At the same time, they must maintain
minimum essential stocks throughout the distribution system to retain maximum flexibility and mobility for
future combat operations. The need to protect ammunition support activities (ASAs) from rear area threat
activities complicates muni-tion support operations. Military Police (MP) units augment ammunition units to
provide security for ASAs.
Ammunition units may find themselves close to combat. In such situations, units must continue to provide
essential munitions support while relocating away from the threat. Disruptions from threat forces are likely to
occur throughout the theater of operations, from brigade support areas to deep within the communications zone
(COMMZ).
CSS CHARACTERISTICS
The tenets of Army operations doctrine, as presented in FM 100-5 (see Figure 1-1), are basic to operational
and tactical success on the battlefield. These tenets also establish the framework for organizing sustainment.
TENETS OF ARMY
OPERATIONS DOCTRINE
Initiative
Agility
Deptli
Synclironization
Versatility
1-2
FM 9-6 CHAPTER 1
Figure 1-1. Five tenets of Army
operations doctrine
Doctrine enables the combat force to take advantage of opportunities to achieve tactical or operational success.
Ammunition units must follow the five logistics characteristics, as presented in FM 100-5 (see Figure 1-2), to
support combined arms operations.
LOGISTICS CHARACTERISTICS
q Anticipation
q Integration
q Continuity
q Responsiveness
q Improvisation
Figure 1-2. Five logistics characteristics
Anticipation
Combat service support (CSS) com-manders must anticipate future events and the needs of combat
commanders. Staffs must devise and develop new methods for supporting those needs. While the unit is still
supporting current operations, the logistics planner must forecast munitions demands based on future
operations plans. Logistics planners must anticipate events and still remain flexible enough to accommodate
likely contingencies. Successful anticipation in munitions support operations is the ability to meet shifting
demands resulting from rapidly changing tactical conditions, to best support combat units, it is imperative that
logistics officers be tactically and technically competent. See FM 100-5 , Chapter 3, for a more detailed
explanation of this charac-teristic.
Integration
Unity of effort requires that CSS commanders fully integrate logistical support into the tactical and operational
plans of the combat commanders, munitions support must be bold, innovative, and based on a clear
understanding of the commander' s intent; however, guidelines for safe, secure operations must be followed.
Combat commanders require the greatest possible freedom of action; therefore, munitions units must organize
to support the combat forces and their operations. Also, munitions support must be fully integrated into
deception plans.
Continuity
Continuity in munitions support is a critical factor in allowing combat commanders to have depth, retain
momentum, and maintain the initiative. The continuity of sustainment is paramount to the continued success
of the operation. While the tempo of combat operations varies, sustainment operations never cease. During
lulls in combat, munitions units must rebuild combat loads and replenish stocks. Also, they must conduct
inspections, preventive maintenance services, repacking, demilitarization, destruction, and retrograde
operations.
Responsiveness
All munitions support units must be responsive to the changing needs of the combat user. They must be
1-3
FM 9-6 CHAPTER 1
prepared to relocate their support base and redirect incoming munitions without interrupting the flow of
ammunition to the fighting force. CSS plans must be flexible to allow the combat commander the ability to
fully exploit a tactical opportunity.
Improvisation
Improvisation is the ability that allows the commander to react to unexpected and unanticipated events and to
exploit them to the fullest to accomplish his mission. No amount of planning can account for all possible
contingencies on the battlefield. When the normal supply of ammunition is interrupted, extraordinary effort,
innovative supply procedures, and other unconventional methods may be needed to support combat operations.
However, improvisation is not the answer for poor prior planning on the part of the commander.
PLANNING GUIDANCE
The CSS commander should use the four support considerations (see Figure 1-3) as a guide when
incorporating combat service support sustainment into operational plans.
SUPPORT CONSIDERATIONS
q Support combat commander's
intent.
q Support forward.
q Maintain total asset visibility.
q Rely upon the Army's system of
effective leadership.
Figure 1-3. Four support considerations
The first consideration is supporting the combat commander's intent. The com-mander's intent may change
with the situation and depends on many variables.
The second is supporting as far forward as possible. As ammunition containers arrive in theater, they are sent
forward to a TSA or CSA. At the CSA the containers are unloaded, and the ammunition is configured into
mission configured loads (MCLs). The MCLs are then sent forward to ASPs or ATPs.
The third is maintaining total asset visibility (TAV) to meet the needs of the combat forces. TAV means that
munitions supplies are tracked from the time that they are introduced into the distribution pipeline until they
arrive at their final destination so that their exact location is known at all times.
The fourth is relying upon the Army's system of effective leadership to adapt to the changing needs of the
battlefield. Effective leadership enables ammunition unit commanders to accomplish their critical munitions
support mission to the combat forces. All commissioned officers, warrant officers, and noncommissioned
officers must be effective leaders as well as technically and tactically proficient.
MUNITIONS STRATEGIC, OPERATIONAL, AND TACTICAL LOGISTIC LEVELS
Levels of munitions support parallel the strategic, operational, and tactical levels of war (see Figure 1-4). At
the strategic level, the national military strategy determines the theater strategy. The theater campaign plan is
derived from the theater strategy and links the operational level (joint task force [JTF] campaign plans) to the
strategic level (theater strategy). Plans for conducting major operations are derived from the JTF campaign
1-4
FM 9-6 CHAPTER 1
plan. Battles and engagements are the tactical level components of major operations. Ammunition support is
an integral part of the plan at each of these levels.
Munitions support is instrumental to the commander in building, sustaining, and projecting combat power to
shape the battle. It is an essential part of the logistics system at each level of war. The theater (operational
level) munitions system links the strategic and tactical levels of war. For more information, see FMs 100-5 ,
100-10 , and 100-16 .
NATIONAL SECURITY STRATEGY
& POLICY DIRECTIVES
NCA GUI DANCE TO CI NCs
NATIONAL MILITARY STRATEGY
THEATER STRATEGY
THEATER CAIVPAIGN PLANS
SUBORDINATE JO INT TASK FORCE
CAMPAIGN PLANS
MAJOR OPERATIONS
Figure 1-4. Levels of war and guidance hierarchy
Strategic Level of
Munitions Logistics
The strategic level of the munitions logistic system is the support base for all deployed forces and provides
munitions based upon projected munitions expen-ditures. The strategic munitions logistic system includes
special activities under Department of the Army (DA) control. These include national inventory control points
(NICPs), national maintenance points, depots, arsenals, plants, and factories. Supporting the strategic level of
munitions is the function of these CONUS organizations or the theater base in the COMMZ and is coordinated
with the logistics support element (LSE).
1-5
FM 9-6 CHAPTER 1
The LSE is the forward element of the munitions logistical base. It provides limited strategic level or other
directed logistics support in the theater on an interim basis. The Army service component commander (ASCC)
(formerly known as the theater commander) has command and control of the LSE.
An LSE consists of military, contrac-tors, and civilian employees. They provide support within, as well as
outside, the theater of operations, producing a seamless system. To optimize the logistics flow, the munitions
logistics system is centrally managed at the strategic level and decentralized at the operational and tactical
levels.
The United States Army Materiel Command (USAMC) coordinates strategic organization actions through the
LSE deployed in the theater. The early deployment of the LSE ensures a positive link to deploying ammunition
units. Also, the LSE may have to fill gaps in the munitions support force infrastructure until the deploying
units arrive in theater. The initial deployment will be for logistical assistance along with the other logistics
personnel assigned to major units. The LSE does not replace capabilities provided by munitions support units
in the force structure. Rather, it provides an interface between the strategic and operational munitions logistics
levels.
Operational Level of
Munitions Logistics
The ASCC links Army plans to the combat commander's strategic level plans. The Army forces (ARFOR)
commander links his plans to the operational level plans. These links enable the operational level of munitions
logistics to support the com-mander in chief's (CINC's) plan. See FM 100-7 for more information.
Providing this support in a force projec-tion environment presents new challenges. The ARFOR commander
establishes priorities for operational level munitions. Operational bases within a theater provide strategic and
operational munitions support to the tactical forces. Based on METT-T, the CINC develops a munitions
organization capable of executing munitions CSS tasks to support the campaign plan.
The difference between the operational and tactical levels of munitions logistics is the longer planning and
preparation time required to support extended operations. The operational level of munitions logistics
encompasses support required to sustain campaign plans and major operations. It attempts to balance current
consumption of munitions supplies with the needs of future major operations. It also enables success at the
tactical level of war.
Operational munitions support signifi-cantly impacts the ARFOR commander's decision process. The
commander uses METT-T to determine logistics time and distance factors, throughput, and lines of
communication (LOCs). Assured logistics communications supporting high data transmission rates with the
national industrial base provide TAV of critical items. In-transit visibility (ITV) allows the commander to
know the location of resources in transit and to allocate them based on their projected arrival. The operational
level of the munitions logistic system provides the link between the strategic and tactical levels.
Tactical Level of
Munitions Logistics
The tactical level of munitions logistics sustains the tactical commander's ability to fight battles and
engagements. Successful tactical level munitions logistics provide the right munitions, on time, at the correct
location to the requesting unit. Mobile, responsive capabilities are essential for prep-aration and execution of
the tactical level of munitions logistics.
The munitions distribution system includes all supply activities needed to provide munitions to the using units
within a theater of operations. Munitions requirements from combat battalions and brigades proceed through
1-6
FM 9-6 CHAPTER 1
the materiel management channels of the divisions, corps, and theater until they ultimately reach the
CONUS-based NICP.
The use, and therefore the structure, of ASAs have evolved. ASAs vary in size, capability, and mission. They
are not bound by strict, hierarchical support structures but are based on projected mission requirements.
SUPPORT STRUCTURES
Munitions support units are organized to meet mission support requirements. Each unit has the appropriate mix
of personnel, MOS skills, tools, and equipment to accomplish assigned missions. Chapter 2 of this manual
provides more information on the structure of munitions support units and doctrine.
1-7
FM 9-6 Chapter 2
CHAPTER 2
MUNITIONS SUPPORT STRUCTURE
PURPOSE AND SCOPE
This chapter describes the munitions support structure and distribution system. Topics include the two types of munitions support
units: MOADS-PLS units and modular ammunition units. Also discussed is the flow of munitions, information, and documents, as
well as the responsibilities of distribution managers at each echelon.
AMMUNITION
SURGE SUPPORT
Major operations and deployments create a tremendous demand on CONUS ammunition depots and port facilities. The Army no
longer has massive stockpiles of munitions outside CONUS (OCONUS), and the amount of Army prepositioned stocks (APS) are
limited. This leaves stateside depots and ports to provide most of the munitions required in an operation. Very early in the
deployment process, planners must provide augmentation support to these depot and port facilities, a significant number of the
Army's munitions units are in the Reserve Components (RC). For that reason, RC units should assist in the planning process.
Also, RC munitions units will probably assist in providing both planning and surge support.
When planning to use RC units to provide surge support, planners must consider the time required to mobilize and deploy the
units. It usually takes an RC unit at least two weeks to complete the mobilization process. This time must be factored into all
operational plans.
When the modular ammunition unit concept is implemented, one or more medium or heavy lift platoons may be assigned to each
depot and port requiring augmentation. The number assigned will depend on several factors:
q Projected size and duration of the operation.
q Projected amount of munitions to be shipped.
q Size of the depot or port and the facilities, equipment, and personnel organic to the depot or port.
q Readiness level of augmentee units.
Providing surge support to CONUS depots and ports is critical to the success of any operation. Ammunition sitting in state-side
storage facilities does not win battles; the failure to get it to the theater of operations may result in unnecessary casualties and an
unsuccessful operation.
SUPPORT STRUCTURE
OVERVIEW
The mission of the munitions support structure is to deliver the required type and amount of munitions to the combat user at the
time and location it is needed. This requires an efficient, effective, and flexible munitions distribution system. To meet the needs
of combat commanders, the munitions distribution system must adhere to the sustainment imperatives presented in FM 100-10 and
Chapter 1 of this manual.
AMMUNITION
SUPPORT ACTIVITIES
Three types of ASAs are in the theater: TSAs, CSAs, and ASPs. An ammunition transfer point (ATP) is not considered an ASA
because of its temporary nature.
The ASA mission is to receive, store, issue, and maintain the theater's conventional ammunition stocks. Also, ASAs configure
ammunition into MCLs. Once configured, MCLs are shipped forward to ATPs for issue to combat units.
Theater Storage Area
Operations
The TSA encompasses the storage facilities located in the COMMZ. This is where the bulk of the theater reserve ammunition
2-1
FM 9-6 Chapter 2
stocks is located. TSAs are operated and maintained by one or more general support (GS) ammunition companies, or by one or
more medium or heavy lift modular ammunition platoons. Besides shipping ammunition to CSAs, the TSA provides area
ammunition support to units operating in the COMMZ.
A TSA receives most of its ammunition in International Standardization Organiza-tion (ISO) containers. The unit operating the
TSA must have the capability to move containers on and off railcars and line-haul transporters. To facilitate shipment, TSAs must
be located where there is easy access to highways, railroads, airheads, and ports (see Figure 2-1). When a TSA's wartime stockage
objective exceeds 25,000 short tons (ST), a second TSA should be established.
The TSA stockage objective is determined by the ASCC. AR 710-2 contains basic days of supply (DOS) policy for Class V. The
theater army area command (TAACOM) ammunition group must keep the operational level materiel management center (MMC)
informed of storage limitations or shortages in each TSA.
Corps Storage Area
Operations
The CSA is the primary source of high-tonnage ammunition for the division and corps. It is operated by one or more GS
ammunition companies or one or more medium or heavy lift modular ammunition platoons. The number of units assigned to
operate a CSA depends on the corps authorized ammunition stockage level. CSAs receive 50 percent of their ammunition from the
port of debarkation (POD) and 50 percent from the TSA. At a minimum, each corps will identify an ASA to meet these
requirements.
CSAs provide 100 percent of the ASP's ammunition and 75 percent of the ATP's ammunition, configured as MCLs. Besides
providing ammunition to ASPs and ATPs, CSAs provide area ammunition sup-port to units operating in the corps rear.
One CSA is normally required to support ASP and ATP operations for each committed division. Stockage objectives for the CSA
are established by the corps support command (COSCOM) and are based on projected theater combat rates. Initially, the stockage
objective of a CSA should be 10-15 days of supply. After the initial combat drawdown, the CSA should maintain 7-10 days of
supply. When a CSA's wartime stockage objective exceeds 25,000 ST, a second CSA should be established.
xxxx
2-2
FM 9-6 Chapter 2
Figure 2-1 . Flow of munitions in a thieater of operations
The COSCOM ammunition battalion analyzes workload requirements based on the forecast and resupply requirements provided
by the division ammunition officer (DAO). From this requirements analysis, the battalion determines how to best provide
ammunition resupply to the combat units it supports.
The ammunition battalion must synchronize ASA operations with corps transportation assets to ensure the timely movement of
ammunition stocks. With the incorporation of modular units, the number of medium lift and heavy lift platoons will be based on
workload. At a minimum, one MLP will be required at each CSA to meet MCL workload.
Ammunition Supply Point
Operations
ASPs are another source of ammunition for the division. ASPs receive, store, issue, and maintain a one- to three-day supply of
ammunition. ASP stockage levels are based on tactical plans, availability of ammunition, and the threat to the resupply operation.
ASPs are located in the division rear. Normally, three MLPs are required to support a division and to provide manning for the
division rear ATP. An ASP is normally operated by a direct support (DS) ammunition company or one or more medium lift
modular ammunition platoons. (A DS ammunition company can operate up to three ASPs plus an ATP.) If the ASP must handle
containerized ammunition, based on METT-T, HLPs must be assigned to the ASP. Depending on METT-T, engineer support may
be required to establish and maintain the ASP. During the ASP site selection process, commanders should focus on locations that
minimize the need for engineer support. Possibilities include villages, commercial buildings, or farm complexes.
ASPs provide 25 percent of each ATP's ammunition requirement in the form of MCLs. Besides supporting ATPs, ASPs provide
ammunition to units operating in the division rear area. These nondivisional and corps units normally receive support from the
closest ASA.
Ammunition Transfer Point
Operations
ATPs are the most mobile and responsive of the munitions supply activities. CSAs and ASPs deliver ammunition to the ATP using
corps transportation assets. This ammunition is kept loaded on semitrailers or PLS flatracks until ATP personnel transload it to
using unit vehicles. If the situation demands, the ammunition can be transferred immediately to using unit tactical vehicles.
ATPs receive about 75 percent of their ammunition as throughput from the CSA. The other 25 percent comes from an ASP and is
in the form of MCLs.
ATPs are located in each brigade support area (BSA) with an additional one in the division support area (DSA). The mission of
each ATP is to provide 100 percent of the ammunition required by all infantry, armor, artillery, combat aviation, combat engineer,
and air defense units in its sector. This includes divisional and non-divisional units (i.e., corps artillery) operating in the brigade
area. A DAO noncommissioned officer (NCO) is located at each ATP to control the issue of munitions.
The corps DS ammunition company operates the ATP in the DSA. This ATP supports all corps, divisional, and nondivisional
units in the DSA. It receives mission guidance and responds to the priorities established by the DAO.
Each maneuver brigade has a forward support battalion (FSB) that operates an ATP. ATPs are operated by the ammunition section
of the supply company in the FSB. These ATPs provide ammunition support to all units in the brigade support sector and receive
mission guidance from the DAO.
The FSB support operations officer, in conjunction with the DAO NCO representa-tive, coordinates directly with nonorganic units
supported by the ATP. Their munitions requirements are consolidated by the support operations officer/DAO, and their request for
resupply consolidated with the brigade request. The DAO/movement control battalion (MCB) and the FSB support operations
officer coordinate the location, amount, and type of munitions (MCLs) to be received at the ATP. Munitions are delivered by
corps transportation assets. ATP personnel interrogate radio frequency (RF) tags of arriving PLS shipments to gain immediate
visibility of the shipment and to identify the organization to which it will be issued.
Units arriving at the ATP to pick up munitions drop off empty, or partially empty, PLS flatracks and retrieve fully loaded
flatracks. ATP personnel assist units without the PLS to transload munitions. Uploaded flatracks are normally issued in the same
configuration as received.
All empty flatracks are shipped back to the nearest ASP, CSA, or TSA as soon as possible. All issues and turn-ins are reported by
the DAO representative. The unit ammunition turn-ins are picked up for immediate retrograde by corps transportation assets used
2-3
FM 9-6 Chapter 2
to deliver ammunition resupply. A DAO representative attaches RF tags to retrograde shipments. The movement tracking system
(MTS) tracks ammunition returns as they are retrograded. The MTS also allows shipments to be redirected if necessary.
AMMUNITION UNITS
The ammunition force structure is evolving. In the near future, and well into the twenty-first century, ammunition units will
continue to become smaller and more flexible and capable of deploying more rapidly.
Headquarters and Headquarters Company, Ordnance Group
(Ammunition) (DS/GS)
The mission of the headquarters and headquarters company (HHC), ordnance group (ammunition), is to command and control
assigned or attached DS and GS ammunition units (see Figure 2-2, page 2-6). The ordnance group is primarily responsible for the
ordnance support structure for ordnance units assigned to echelons above corps (EAC). It is responsible for TSA operations. Also,
the ordnance group commands, controls, and plans ammunition missions, to include the following:
q Retrograde activities.
q Enemy ammunition inspection, pro-cessing, and shipping.
q Operating ASAs for COMMZ transient units.
q Advising ASCC on theaterwide ammunition policy.
q Establishing ammunition supply and maintenance procedures consistent with the policies and directives of the ASCC and
the corps.
The ordnance group executes missions through subordinate ordnance battalions or in coordination with area support groups
(ASGs). The ordnance group provides technical assistance through the materiel section to ASG ordnance planners. Also, the group
can provide coordination for resolving support problems between subordinate units, supported units, and CONUS depots.
Ordnance group technical assets can be deployed before, during, and after operations to work in concert with the taacom, the LSE,
and the theater army materiel management center (TAMMC).
The ordnance group (ammunition) is assigned to a TAACOM. It is allocated one per theater or one per two to six battalions
commanded. At 100 percent of assigned personnel, ammunition group missions include the following:
q Command, control, and staff planning for up to six subordinate units.
q Technical direction of subordinate unit ammunition support operations, except for inventory management functions for
which the TAACOM MMC is responsible.
2-4
FM 9-6 Chapter 2
Headquarters and Headquarters Company
Ordnance CSroup, Ammunition
HHC
GROUP Hq
COMMAHD
SECTION
rnMUIIHICIATIONS
SECTION
AD.JIITANT
SECTION
OFF RATIONS &
IITELLIGENCE
SECTION
HO COMPANY
LOMPjaNV iiq
SllPPlY
SECTION
MATERIEL
SECTION
Diss Inn: Cammand and cpnlrcil assigned or aliached , DS and GS aminuniliDn units
or Other atoched units.
Aseignmenl: Assigned ta a TAAC 01^.
CapabiitlBs: M 100 percenl of assigned personnel, this unil can provde"
• Command, conEtiol.and slaff planning for up id s\y suboifdinale units.
• Technical direction orver ammynition support missions of subordinate
units, snoept for inventory managsmont functions for which' tl^e oporalional
ItvEil IVIMC is reipDrisible.
BseIg of Allacalion: iNormallj^ane p«rTAACOM or one per tviti id siK battalions
CQ'Tnanded
UoblJhv: This unit is required to mme 50 percent of its TOE equipnnent and personnel
in a singls M, using organic ^^ eh icies.
Figure 2-2. Ordnance group, ammunition (DS/GS) ( TOE 09662L000 )
Headquarters and Headquarters Detacliment, Ordnance Battalion (Ammunition) (DS/GS)
The mission of the headquarters and headquarters detachment (HHD), ordnance battalion (ammunition) (TOE 09466L000 or TOE
09666L000 ), is to command and control assigned units or attached DS and GS ammunition units or other attached units (see
Figure 2-3 and Figure 2-4). These units ensure compliance with ammunition supply and maintenance procedures established by
the TAACOM.
This unit is assigned to a COSCOM or a corps support group (CSG). It may also be assigned to a TAACOM, normally attached to
an HHC, conventional ammunition group (DS/GS). A minimum of one ammunition battalion is required per COSCOM to support
a fully deployed corps. This battalion is allocated one per three to five companies commanded. It can provide:
q Command, control, and staff planning for up to five subordinate units.
q Technical direction over ammunition support operations of subordinate units. The exception is inventory management
functions, for which the operational level MMC is responsible.
MOADS-PLS
Units
2-5
FM 9-6 Chapter 2
The structure of ammunition units and the munitions support concept are revised as combat doctrine evolves.
Under MO ADS, a large number of troops were deployed OCONUS to maintain and distribute the vast stockpiles of munitions
stored in overseas depots. The MOADS system was designed for break-bulk resupply and multiple transfers of munitions.
The conversion of units to MOADS-PLS has resulted in the more rapid movement of supplies and less frequent transfers through
the use of MCLs. Other results under MOADS-PLS include the requirement for fewer soldiers and less equipment. Also, this
system provides limited ammunition unit flexibility and ITV of munitions stocks. Table 2-1 shows the lift capability and
manpower requirement for each type of materials handling equipment (MHE) listed.
General Support (GS) Ammunition Com-panies (MOADS-PLS). General support companies, which are organized under TOE
09433L000 and TOE 09633L000, establish a CSA/TSA in the COMMZ and corps rear area and behind each committed division.
Also, one or more GS ammunition companies will establish a CSA or TSA. Allocation of these companies is based on theater
stockage objectives and supported force requirements.
The CSAs provide munitions support throughout the corps and serve as the primary source of high-tonnage munitions for the
division. Figure 2-5 and Figure 2-6 illustrate the structure of GS MOADS-PLS units.
Direct Support (DS) Ammunition Com-panies (MOADS-PLS). Direct support companies, which are organized under TOE
09484L000 , establish three ASPs and a rear ATP to support divisional and nondivisional units in the division area. One DS
company is allocated per division. Figure 2-7, page 2-12, illustrates the structure of DS MOADS-PLS units.
Headquarters and Headquarters Detachment
OrdharK e B att al I orv Am munition, DS/GS
HHD
. ORDINANCE BATTALiON
(AMMUNITIOf^
{D5IGS)
1
1
BATTALION
1
HQ
DFTArHMFHT
1
1
DETACHMENT
HQ
1
1
1
1
COMMAND
AD
JUIAHI
COMMIJHKJllinNS
OPERATIONS fi
SECTION
Si
iCTIOH
SECTION
irfTEL LICENCE
SECTION
1
1
1
1
MATERIEL
SUPPLY
UHlTMIHISTftY
^tcnON
^LLIIOn
ILAM
Hlessmn: CDmmand and cDntral Dfassigned or^Hached csmpaniesor modular
ammunitmn plstaens Dr other attached unijs.
AsslginmcnC .^^iQnedto a CSG.
Capabilities: At IDO percent at asagned personnel, this unit can prDvlde:
• Command, control, and etaff planning For two to fhs subordinaiie units.
* Technical direction ovar ammunition support missions of subarcJinale units,
sjj rapt for inventor J management functions, for wtiich the ape rational level
MMC is respcnsibie.
Basis of Alhicallan: Mormally one par two to Ina com>panlBS commanded.
2-6
FM 9-6 Chapter 2
Mability; This unil is required to more 50 percent of its TOE equipment and
personnel in a single lifl, using organic vel^icles.
Figure 2-3. Ordnance battalion, ammunition (DS/GS) (TOE 09466L000)
Headquarters ^d Headquarters Detachment
Ordnance Battalion, Ammunition, DS/QS
ROMANCE BATTALION
AMMUNITION
HEADQUARTERS
r.ouMAHn
SECTION
AriJriTAHT
SECTION
MATERIEL
SECTION
HqOETACHNENT
DFTACHMFNT
SECTION
SUPPLY
SECTION
OOMMUHICATIGHS
OPERy\TIOMS*
INTELLJGENCE
SECTION
limTMINISTHy
TEAM
Miuion: Command and coinlrol aEs.igns'd or altacihed , ammunition companiee or
modular ammunilmn plalouns nr ulliBr aliarzhed unita.
Asslynmsttt Assigned lo aT<MC0h3 or ordnance e<in munition group.
Caiiabllltles: f^i 100 percent of assigned pereor^nel, Ihls unil can provlds:
* Cofnman d , CO nlro I , a n d slalf p la nnin g for two ta f ive su bo rdin ata u nil&
' TEchinical dlnedian dve! ammunitlan support mi^slaris a^ BuboirlinBlE
unils. eKceptfor inventofj marniagennent functions for whnch ihe opera-
tional level MMC rsraepor^sible.
Basis Df AllocotiD n: NDrmalljf one per twi3 to fKre wmpanie? i:9rriman[Jed
Mobility: This unit is raquirod to move 60 percant of its TOE aquipmeni and
personnel in a single liift, ueing organic vehicles.
Figure 2-4. Ordnance battalion, ammunition (DS/GS) ( TOE 09666L000)
2-7
FM 9-6 Chapter 2
ORDNANCE COMPANY
AMMO (PLSf1\^0ADS)
C3A
tOMnftHVHO
conrKu
SECTION
tifl lot
5ECT10H
m
MAINIF NANCE X:
SERVICE PLAIOOH
®
c5;a
AMJIIINIlltH
SJPPLY PLATOON
UbsIdh: E^ablishes. and DperatES an ammunlti'Dn s up ply Fa-cilit]' engaged in necenrinj, Coring,
reurarehidiusing, combat configuring, and issuing ccnventicnal ammunHicn using the PLS.
Capaitllltles: ^ level 1 . thic unit (objecl lire TOE) has 3 daily capability Id receive 1 ,7^0 STONc
Fj:d luL ^u: break-bulk a nfimuriticn en IheaEer eermitraile-re rrem the port and 1 /50 STONc pallallzed
bnaak-bulk ammumitlDn PLE racks uploaded on theater eBmilrailBrs from tha TSA. The unl! conligures
and issues up to 3 500 ETOHs of ammunilion loaded on PLS racks for a lotal of 7,000 STONs per day.
AGslgntttHiit: To rear CSGs: ordnance battalion , ainmunitian , DS^S, TOE 09466 LOOD.
BiBis uf AllDcadan:' One ccmpany per every 7^00 STOhJa Df ammurrtion received, stured, laEued.
and configured.
Mobility: Jnit is 50 percent nfiobile , less ammunilian stacks.
Referencis: FM 54-30
FME3-3
Figure 2-5. Ordnance company, ammunition (MOADS-PLS) (CSA) (SRC 09433L000)
2-8
FM 9-6 Chapter 2
OFIDNANCE C0MPAh4Y
AMMO (PLSMOADS)
TSA
03
®
ISA
COWJAH/HQ
SECTlOn
SECTION
UAIMTFUAUCF A
SERVICE PLATOON
nmi'iuNiiioN f
SUPPLY PLftlOOH J
1
UAINTEHANCE&
SERVICE PLATOON HO
rj^AlUIFHAMTF
SECTION
SERVICE
SECTION
1
1
ATJIMnf^llPPLV
PLhIOOH HQ
ROUGH TERRHIN
F0FWLIFT5ECTIOH
CRANE
SECTION
TECHNICAL
SECTION
r
1
1
MlGslDit: EslJibllElisE and operates an ammy nition supply facility engaged in Itie receipt,
slorage, rewanehousing , conlainer unsluffing, and issue DfconventiDnal ammunition using
tha PLS.
Capabililies: A1 kvel 1 , this unit ^objective TOE) has e daily capability to necelve '2,333 STOMs
containeri^edijpalleitifeci bceak-bulk ammunilion on theatef eemiu aiders from ttie perl and 2^33
STOMs DantairErizBd/palelizied brsak-bjlk ammunitiDn PLS rackE uploaded aniliealBrsBmilrailers
from the port. The unit unstuffs tonteiner?. and issue* up to 3 5O0 STOMs of ammunilion on R.S
racks for a lEJtal of 7,000 STONs per daj/.
Assignment; To TAACOMannmunition gfoup, mdnance battalion, ammunilion, DEfCS,
TOE093B6U000.
BiEB uf ALIutdlionc: One companj per every 7iQD0 STONs of ammunilion received, sior'ed,
issued , and contigurBd
Motiil^: Jolt is SO p«ircent mobile , less ammunitjon stDi^s.
R bI Bf encBs: FM G3 -A
Figure 2-6. Ordnance company, ammunition (MOADS/PLS) (TSA) (SRC 09633L000)
2-9
FM 9-6 Chapter 2
COMPAIir
m
CONTROL
SECTION
ORDWANCE COMPANY
AMMO, PS
(PLSiTiflOADSl
SECTIQH
MAimt NANCE K
SEFMCEPLflTOOM
o<l
(D(fl)
AMMUNITION
SUPPORT
n AICKJN
ATP
SFCTIrtM
Mission: Eslablishesand operates thnee geograpFijcelly dispersed ASPs and an
ATP enaaged in receiving, etoring, rcwareli a using, com bat-configuring, and issuirrg
cnmensionalammuniLlon using llie PL5.
CapdbilitJBs: At e^^ eM , 1his unil [DtijectrvB TOE) prDvidss ths fDllDwing lift capability:
ASP,S53D STONs; and ATP. 970 STONs Lifl is normeilj divided between receipt,
issue, CO nfigu ration rito MCLs, and slarsge.
Ba&ls of Aliocallonr'Employmonl: One per dh/ision; aesignsd to a COSCOM. suttacliad
tea CSBiraCSG.
Muhillly: Jnit is 50- percent mobile, lees ammunitien stacks.
ReferRiirfsr FM 54-30
FMG3-3
Figure 2-7. Ordnance company, ammunition (DS) (MOADS-PLS) (SRC 09484L000)
Table 2-1. MAN/MHE team lift capabilities by STONs per day
MHE
GS
(TSA/CSA)
DS
(ASP)
ATP
6,000-lb variable-reach forklift
187
119
88
4,000-lb rough-terrain forklift
126
58
NA
7 1/2-ton rough-terrain crane
NA
219
NA
65-ton container crane
295
NA
NA
6,000-lb rough-terrain forklift
165
74
75
10,000-lb rough-terrain forklift
116
52
NA
5-ton rough-terrain crane
NA
200
NA
20-ton rough-terrain crane
257
NA
NA
2-10
FM 9-6 Chapter 2
* When being operated, aWforklift man/MHE teams require two persons per forklift plus a ground assistant. Crane
men/MHE teams require tliree persons per crane-an operator and two ground assistant operators. Ground assistants
are for safety purposes; any personnel in the area may perform this task.
Modular
Ammunition Units
With the end of the cold war, the Army began to evolve from a forward-deployed force to a primarily CONUS-based force
capable of projecting combat power to any part of the world and to any type of theater.
The MO ADS doctrine and force structure were designed to support a forward-deployed force. Conversely, the wide variety of
possible missions facing the CONUS-based force projection Army requires an ammunition distribution system capable of
supporting any contingency. This more flexible distribution system is based on the concept of modularity.
Under the modularity concept, only the number of soldiers or amount of equipment needed to support the forces are deployed.
This might mean deploying a single platoon to support a brigade contingency or a company with added platoons attached to
support a mature theater.
The initial deployment of modular ammunition units to a theater will consist of one or more platoons. Heavy lift modular platoons
are capable of loading, moving, and unloading 20-foot ISO containers. The MLP has no container handling capabilities.
As the theater matures and more modular ammunition units arrive in theater, a conventional command and control structure is
established, and the modular platoons are formed into company-sized units. Table 2-2 illustrates modular ammunition platoon lift
capacities.
Table 2-2. Modular ammunition platoon
lift capabilities
HEAVY LIFT PLATOON
MISSION
LIFT CAPACITY |
RECEIVE
886 ST
REWAREHOUSE/RECONFIGURE
886 ST
ISSUE
886 ST
TOTAL LIFT CAPABILITY
2,658 ST
MEDIUM LIFT PLATOON
MISSION
LIFT CAPACITY
RECEIVE
376 ST
REWAREHOUSE/RECONFIGURE
376 ST
ISSUE
376 ST
ATP
393 ST
TOTAL LIFT CAPABILITY:
1,521 ST**
2-11
FM 9-6 Chapter 2
MAXIMUM STORAGE PER PLATOON
HEAVY LIFT PLATOON
7,100 ST*** 1
MEDIUM LIFT PLATOON
7,046 ST***
* Short tons (ST) per day.
** When operating in a CSA or TSA with no ATP mission, the MLP has a total
lift capability of 1,521 ST (507 ST per mission). When the ATP section of the
MLP is employed separately, it has a lift capability of 393 ST/day. Each MLP
can provide one-third a rear ATP. The figures are based on 24-hour operations.
*** This capacity represents a portion of the designated level of the theater
stockage objective. i
A modular ammunition company consists of a company headquarters platoon and from two to five heavy and/or medium lift
platoons. The headquarters platoon (Figure 2-8, page 2-15) is capable of commanding and controlling multiple geo-graphically
separated platoons as METT-T requires. However, the headquarters platoon must be collocated with at least one of these platoons
for logistical support. This headquarters is capable of consolidating platoons in the COMMZ and providing support to corps and
division areas.
The ammunition platoon (heavy lift) (Figure 2-9) is capable of supporting units on an area basis through receipt, storage, stock
management, inventory control, and issue. Also, this platoon is capable of loading or off-loading 20-foot ISO containers from
inbound or outbound transportation assets. It employs PLS vehicles to move stocks, rewarehouse, move configured loads to a
holding area, and move organic equipment. The prepositioned munitions ships will have a portion of the unit' s equipment aboard.
Therefore, at least one of these platoons must arrive in theater at the same time or before the prepositioned ships. A platoon can
operate independently from an ammunition company headquarters, but needs outside support for sustainment. It is 100 percent
mobile, less ammunition stocks.
The ammunition platoon (medium lift) (Figure 2-10) does not have container- handling equipment. This platoon can unstuff a
20-foot ISO container, if necessary, to mission configure break-bulk munitions. The ammunition platoon is capable of receipt,
storage, stock management, inventory control, mission-configuring, and issuing to supported units on an area basis. The
ammunition platoon can operate independently from an ammunition company headquarters, but it requires outside support for
sustainment. It is 100 percent mobile, less ammunition stocks on hand, and has PLS vehicles to enable the rapid movement of
ammunition within the ASA.
2-12
FM 9-6 Chapter 2
Modular Ammunition Company
Com pary H eadqu alters
SRC OMOSLDOO
MODULAR AMMUNITION COMPANY
COMPANY HEADQUARTERS
MODULAR PLATOONS
(MLP or HLP)
T
t
Mission; Prmides ajnrimand, contral, admin istra live, planning, and logialicel auppod for
hvo to fivo finoduliir ammuniticin platoons
AssFt)nment: Depandsnn assigned miE£.ian.
Wien assigned the ^P rundion , tlie unit is assigned to 8 CSB (TOE63426LDD0).
Wrtien asignad th& CSA fynclion, iJie unit is aisignad lo a CSB (TOE 63d26U]00) or
a carpE, ^mmunitiDn battalion (TOE Q9SE6LCIQD].
WJien assigned the TSAfunction, the unil is assigned to an arinmunitiDn ballaliDn (EAC)
TOE09666U00a.
dashs at Alia cat iqn: J*s required b^theater operations and the number of modular
ammunitmn platoons deployed.
Mubilh^: Tha company haadquariers ie100 percani mobila.
Figure 2-8. Modular ammunition company headquarters platoon
2-13
FM 9-6 Chapter 2
IVTod uFar Amm unltlon Plato on
Heavy Lift (HLP)
SRC 09503LB00
PLATOON HB^DQUARTCRS
I (KIDSI IIUICI
SECTIOfI
IfClllliM-ll IIItdlH
FORKLIFTSECTIOn
c:itJ)M
^ECnQH
irciisiii'^di^i
SECTIOM
MAIHTENANCEiSEFVICE
SECTION
Mission: Receives and stiips contain eriied ammunilion. ConfiBurea. inspects, issues, manages,
s^ips. and retrogrades a miriunilion stacks. Operatesiindependsntly or»spir1 of a largsr unit.
As-signmenl: AsE,i3nBd Id 3 modulHr ammunitjon campanj' headquarters (TOE D^ilQSlJQQQ).
Wtisn dsplojed independsntly to perform the CSA function, platoons are assigned 1o a CSB
CrOE 63^26Ij00D) or an ammunition batlalicn (corps) (TOE 03^661000).
WInen depbyed independently ta perform ihe TSAfundiDn , ihe unit is assigned to an ammunition
baltaiion (EACJ (TOE 0S666IJCBQ).
Capatilllties: SeeTabla2-1 forklifl capaLiiJIties.
BaGis or Alio cat Jon: As requlfod b^thgateroperallcns, daii^eonnags l*ftrac|uirement£, ortlieator
ammurtitian slockage requiremenle.
Mobililjf; TJie platoon is 1 0D percent mobiie , minus ammunition slocks. Unit depends on
nonorganic transportation assets Id move anjf ammunition supplies on hand. This platoon
should s?<}?sd.lia mt»6 ^try3 id 10 da^e.
Figure 2-9. Modular ammunition piatoon (hieavy iift)
2-14
FM 9-6 Chapter 2
|\f)adu I ar Ammunition Platoon
MediiATi Lift (MLP)
SRC0»5Q3LA0a
PLATOON HEADQUARTERS
1
1
FOOD SERVICE
SECTION
|{C]ll(iM-TFRF[dlH
FORKLFT SECTIOH
irrnsipponr
SECTIOri
MbiMTFUAUcrjsrmriQ
SECTIOM
Iti Alt A IP
SECTION
Mlssloti: Recarves. configures, inspects, issues, msnagas. ships, arid retmgradas nonconlaineriied
afflmuniliDn slocis. Operates indepandenttjf ar as part of a larger unit.
Ass ignment: Assigned To a rncidular ammunition company tie adquarters [TOE iDSJDBtilDO).
When deployed independently or as pad of 3 unil ts perform llie ASPorllie CSA function, platoofie
arp a^Eigned Id 3 C5B (TOE SBi^SLQOD); or u/fien depb^&d to pBrfarm the CSA fundinn, pialDnn?
are assigned lo an ammuniiion bBttaiion (con^s) (TOE 09^661X00).
Wien deployed independently or 3S a unit to perform I l^e ISA function , ihe unit ie assigned to in
anrrTiuniliDn laaitaiion (EACi (TOE 09666 U3QD0-
Capabilties: See Table 2-t Foir liO capabiirties.
Basis or^localion: As required by theater cperetions. daily tonnage lift na quire me nts, or
iheater ammunittcn ^taclogB rBquirBments. and the number af mndular ammuntian pla^lDDnE
deployed.
Mnbllly: The platoon is 1DD percent fmo bile, Tees ammunition stocks. Unit depends on
nonorqAniclran^portstiort assets to niov^ an^ amnhunilion supipli^s on hshd. This platoon
should asp eel to mnMe every 3 1n 1Q days
Figure 2-10. Modular ammunition piatoon (medium iift)
AMMUNITION
SUPPORT TEAM
The USAMC ammunition support team (AST) arrives at immature theater PODs before prepositioned munitions vessels,
sustainment shipments, or munitions units. It estabUshes a point at the PODs where munitions stocks can be accounted for. Also,
the team coordinates the off-loading and distribution of stocks either to storage areas or for direct issue to units from the PODs.
Early arrival of ammunition units is essential to move Class V from the port area.
The concept for employing the AST is dissimilar to the employment of all other LSE organizations. The AST mission is tied
specifically to the accountability and management of APS munitions. These preconfigured loads, stored on logistics ships, are
available for rapid delivery to the theater.
During the early stages of any contingency operation requiring APS munitions, the AST deploys with mirror image prepositioned
(APS) accountable records and quality assurance specialist (ammunition surveillance) (QASAS) support. Normally, this coincides
with the deployment of the LSE advance party. The early departure of the AST from CONUS is necessary to assure that its arrival
is before the port acceptance of the Army's APS vessels.
The AST provides technical expertise and assistance in the following areas:
q Supply,
q Storage,
q Maintenance,
q Surveillance.
2-15
FM 9-6 Chapter 2
q Demilitarization.
q Transportation.
q Security.
q Explosive safety.
q Supplies.
q Packaging.
q Accountability for munitions mate-riel and associated equipment.
AST responsibilities may include, but are not limited to, the following activities:
q Providing theater munitions units with technical assistance in establishing and managing ammunition storage areas.
q Conducting inventories. Maintain-ing initial theater-accountable records.
q Providing for the transfer of DA-owned, NICP-accountable Army reserve stocks assigned to the theater.
q Developing and administering con-tract statements of work.
q Planning and executing retrograde operations.
Deployment of the AST should be based on the tempo of logistical operations in the theater. The major functions of the AST
include the following:
q Preparing for overseas deployment.
q Deploying to theater ports of debarkation.
q Setting up the support team base of operations.
q Transferring the accountability of APS assets from NICP-accountable officers to theater-accountable officers.
q Providing initial theater accounta-bility and Standard Army Ammunition System (SAAS) operations.
q Linking the CONUS sustainment base and the combat logisticians.
q Submitting status reports through NICP to HQ, USAMC, and HQDA.
q Coordinating joint munitions opera-tions as required.
q Providing initial QASAS support to the theater.
Once the AST has established itself in the theater, the ground component commander may expand the AST mission based on the
specialized training and technical expertise of the team. Any expansion of responsibilities must be coordinated with the parent
organization at the time, either the LSE or USAMC.
Headquarters and Headquarters
Detachment, Ordnance Battalion
(Ammunition) (WHNS) (DS/GS)
The mission of the headquarters and headquarters detachment, ordnance battalion (ammunition) (WHNS) is to command and
control assigned or attached units (see Figure 2-11). This unit provides:
q Command, control, and staff planning for up to nine ammunition companies (TOE 09574LB000).
q Technical direction over ammunition support operations of subordinate units, the exception being inventory management
functions for which the operational level MMC is responsible.
This detachment is also involved in the coordination and management of US-owned Class V stocks being received, stored, and
issued by host nation (HN) ammunition units. It can be assigned to a CSG; it can also be assigned to an ammunition group in the
TAACOM.
Ordnance Company
(Ammunition) (WHNS)
The mission of the ordnance company (ammunition) (WHNS) is to provide operational control over US-owned ammunition stocks
being received, stored, warehoused, and issued by HN units to US forces combat units. This company is assigned to an ordnance
battalion (TOE 09574LA00) with one company allocated per HN ammunition company. On a 24-hour basis this unit provides:
q Expertise required to perform stock accountability, stock status reporting, and QA/QC functions for US-owned ammunition
stocks being received, stored, warehoused, and issued by HN ammunition units.
2-16
FM 9-6 Chapter 2
q Coordination needed for maintenance support for US equipment operated by HN units.
q Coordination for operational task-ings.
BATTALION
HQ
X
COMMAND
SECTION
COM MU Ml CATIONS
SECTIOM
ADJUTANT
SECTION
I
MATERIEL
SECTION
OPERATIONS &.
INTELLIGENCE
SECTION
SUPPLY
SECTION
ORDNANCE
COMPANY*
COMPANY
HQ
ORDNANCE COM PANY
TOE D9524LB00
(AMMUNITION)
(WHIMS)
CONTROL
SECTION
1.
QA/QC
SECTION
''Up to nins companies under tfie commajjof snd contnDl of oiis oninsiics baitaSion
Figure 2-11. Headquarters and headquarters detachment, ordnance battalion,
ammunition (WHNS) (DS/GS)
MUNITIONS FLOW
IN THE THEATER
The theater receives munitions from CONUS or OCONUS locations through air and water ports or by logistics-over-the-shore
(LOTS) operations. From there, munitions are transported to the appropriate munitions support activity.
Several factors determine the quantity of munitions moved forward. These factors are as follows:
q Quantity of munitions on hand.
q Current and projected consumption,
q Available transportation.
q Available personnel and equipment.
Determining or Requesting
Munitions Requirements
Combat commanders control the flow of ammunition in their areas of responsibility by using two ammunition supply rates, the
required supply rate (RSR) and the controlled supply rate (CSR). Commanders at each level submit their RSR to the next higher
headquarters. These headquarters review, adjust, and consolidate RSR information and forward it through command channels. At
the ASCC level, the total, unrestricted ammunition requirements are compared against total ammunition assets available (on hand
or expected) to develop the CSR. Chapter 3 of this manual has more information about RSRs and CSRs.
To request ammunition, each unit consolidates its on-hand quantities and forwards its report to the battalion supply officer (S4),
with information copies to the battalion commander and operations and training officer (S3). Company commanders will indicate
in their situation report (SITREP) remarks any critical munitions shortages or forecasted changes in munitions requirements.
The battalion S4 requisitions ammunition based on information provided in the company SITREPs and guidance received from the
2-17
FM 9-6 Chapter 2
battalion commander and S3. The battalion S4 consolidates the entire battalion munitions requirement and submits it to the
brigade S4. When necessary, battalion commanders cross-level within companies or throughout the battalion to meet mission
requirements. The battalion S4 also reports the unit's on-hand quantities by Department of Defense Identification Code (DODIC)
or nomenclature, any critical shortages, and any forecasted changes in requirements in the battalion's SITREP to the brigade.
The brigade S4 consolidates the requests for ammunition and passes them to the support operations officer in the supporting FSB.
An information copy is forwarded to the DAO. The DAO, in conjunction with the corps materiel management center (CMMC),
uses the information copy to determine if on-hand stocks in the ASP are sufficient or if munitions from the CS A or TSA will be
required.
The brigade S4 monitors the munitions on the commander' s tracked items list (CTIL) that require special attention, such as
emergency resupply. The support operations officer consolidates the brigade's munitions requirements and forwards them to the
division support command (DISCOM).
Controlled Supply Rate/
Priority of Issue
The support operations officer, with guidance from the brigade S3 and S4, informs the DAO about the brigade's CSR breakout and
unit priority of munitions resupply. Forecasted critical shortages and changes in requirements, as reported in the brigade SITREP,
are provided to the DAO.
Munitions Resupply
The preferred method of munitions resupply is to deliver as far forward as possible. Ammunition containers are shipped only to
the TSA or CSA. There, they are unstuffed, and the ammunition configured into MCLs sent to forward ASAs. If the situation
requires it or transportation assets are available, munitions may be throughput as close to the unit as possible. Figure 2-1 on page
2-3 illustrates the flow of munitions in the theater.
The CMMC determines whether the munitions resupply will come from the ASP or the CSA. The DAO determines the munitions
status of the brigade ATPs in the division. This information will determine whether munitions within the division can be
cross-leveled to meet munitions require-ments.
If the munitions are coming from the ASP, the CMMC prepares a materiel release order directing the munitions shipment. If the
munitions must be brought forward from the CSA, the CMMC submits a request for munitions resupply to the corps assistant
chief of staff (logistics) (G4).
Munitions may arrive in theater in configured loads. The supporting activity, either the ASP or CSA, reconfigures these loads into
MCLs before transportation assets arrive. The MCB schedules transportation according to corps priorities. The ammunition units
are notified by the MCB of where and when transportation will arrive.
After ammunition has been loaded, the RF tags are verified along with the correct cargo and destination. All ammunition
shipments are tracked through ITV. Delivery coordinates and time are forwarded to the receiving unit or activity, with information
copies furnished to the DAO, the FSB support operations officer, the DAO representative, and the S4. In the event an ammunition
shipment must be diverted within the brigade, the brigade commander or designated representative retains sole authority to do so.
This is accomplished through the FSB support operations officer. Ammunition shipments that must be diverted within the division
are directed by the division commander to the DISCOM commander for implementation.
AERIAL RESUPPLY
Air resupply missions are categorized as preplanned or emergency. Preplanned missions make up the routine air transport service
that supports preplanned or program- med requirements. Emergency air move-ments are initiated by requirements that cannot be
determined in advance.
The movement control officer coordi-nates the movement of supplies with the main support battalion (MSB) and the move-ment
manager in the FSB support operations section. If the movement control officer determines that air resupply is appropriate, he
passes a request through the division transportation officer (DTO) to the assistant chief of staff (operations and plans) (G3). The
G3 allocates helicopters on the basis of all aviation tasks by balancing combat, combat support (CS), and CSS require-ments. The
G4 must ensure the CSS role for helicopters is developed and considered concurrently with the tactical mission. The priorities for
helicopter resupply should be addressed in the operations order (OPORD) and used by the movement control officer.
Emergency requests are passed through supply channels the same as routine requests. However, they are also passed
simultane-ously through command channels from the user to the G3. The G3 approves emergency requests and tasks the aviation
2-18
FM 9-6 Chapter 2
brigade to perform the mission. At the same time, the G4 coordinates with the DISCOM support operations branch so it can task
the appropriate supply activity to prepare the shipment. A liaison officer from the aviation brigade coordinates with the movement
control officer and the requesting unit. Prerigged loads of standard resupply packages may reduce response time for emergency air
resupply. More details on requests for aerial resupply are in FMs 55-2 and 100-27.
COMMAND AND SUPPORT RELATIONSHIPS
Army, joint, and/or combined units or elements may be required to perform their missions within the area of operations (AO) of a
corps, division, brigade, or battalion with which they have no formal command or support relationship. Unless attached for
logistical support, parent units are responsi-ble for providing support to their elements dispersed throughout the battlefield. At
times, mission requirements may exceed the organic support capabilities of the parent unit. When this happens, the parent unit
must coordinate support for its elements with the headquarters controlling that element's AO. Once coordination is accomplished,
the headquarters controlling the AO assumes responsibility for providing logistical support for the units in the AO. The rear
command post (CP) facilitates support of nondivisional units by identifying the name and location of the divisional coordinating
staff element or host unit.
Munitions support for nondivisional units operating in the division's AO is coordinated by the DAO. Nondivisional units attached
to or supporting the brigade combat trains (BCTs) forward their munitions requests through the FSB support operations officer to
the DAO. Nondivisional units attached to or supporting the division and operating in the division's rear area forward their
munitions requests through the DISCOM support operations officer to the DAO. Specific procedures for supporting nondivisional
units are detailed in the Class V section of the service and support annex of the OPORD.
FUNCTIONAL
RESPONSIBILITIES
Each activity or unit in the munitions supply system has functions unique to it. These functions are discussed below.
Army Service Component
Commander
The ASCC has overall responsibility for in-theater receipt, accountability, and management of munitions stocks. The ASCC is
also responsible for the following functions:
q Establishing ASPs, CSAs, and TSAs.
q Coordinating distribution between storage sites and storage sites and forward ATPs; coordinating direct issue to using units
on an area support basis.
Operational Level
Materiel Management Center
The operational level MMC is the support unit responsible for providing theaterwide munitions supply management and
allocation. Support is based on priorities established by the theater CINC. The MMC is the prime interface between the theater and
the CONUS sustaining base, which includes the Defense Logistics Agency (DLA), NICPs, and USAMC. The operational level
MMC communicates with the operational level movement control agency (MCA), the TAACOM, CMMCs, and CONUS.
The MMC provides initial resupply to the corps from several possible theater ammunition sources, as follows:
q Army prepositioned stocks. This includes either ammunition preconfigured on logistics ships that is available for rapid
delivery to the theater or prepositioned ammunition available on a regional basis to support contingencies worldwide.
q Sustainment base production stocks. This includes ammunition either off the production line or stored in depots. These
stocks are shipped to the theater as needed.
Corps
Materiel Management Center
When a corps is the ARFOR, the CMMC is the operational level MMC. In a theater with more than one corps, the ASCC may
establish a centralized MMC to which CMMCs report.
The CMMC provides centralized control of munitions and all other classes of supply within the corps. It is the interface between
corps units and the theater/operational level MMC.
Missile and Munitions
Division
2-19
FM 9-6 Chapter 2
In the CMMC, the missile and munitions division includes three branches: the missile and munitions support branch; the missile
and munitions parts supply branch; and the missile and munitions maintenance branch (see FM 63-3 ).
The missile and munitions division is responsible for ammunition management to include the following:
q Processing requisitions.
q Reviewing the RSR and computing the CSR.
q Directing storage and distribution of ammunition.
q Coordinating with the corps move-ment control center (CMCC) to integrate ammunition movement requirements into
movement programs.
q Providing guidance to division mate-riel management centers (DMMCs).
Munitions Support
Brancli
The munitions support branch exercises staff supervision over munitions support operations. These include supply and
maintenance operations relating to muni-tions, missiles, special weapons, and associated repair parts, special tools, and test
equipment. Responsibilities include:
q Developing plans and policies involving munitions supply and maintenance.
q Providing staff input for munitions planning to COSCOM CSS plans staff branch.
q Developing munitions surveillance policies.
q Maintaining a running estimate of munitions requirements.
q Coordinating munitions require-ments with corps G3 and G4 staff.
q Establishing ammunition supply levels based on corps directives.
q Recommending ammunition supply and storage site locations to the corps rear CP CSS cell.
Missile and munitions officers assigned to the munitions support branch develop operating procedures and plans to implement
munitions supply policies prescribed in ARs 710-1 and 710-2 and SAAS technical manuals (TMs). Other duties include:
q Providing technical advice and assistance to ammunition officers in subordi-nate CSGs and ammunition supply units.
q Coordinating with CSG ammunition officers on cross-leveling munitions support personnel and equipment.
q Recommending establishment and movement of ASAs as the situation dictates.
q Reviewing and updating ammunition planning factors to the theater scenario.
q Monitoring ammunition suspen-sions.
q Recommending adjustments to munitions stockage levels.
q Coordinating resupply of munitions stocks for attrited units at regeneration sites.
Ammunition Battalion
Materiel Office
In the absence of an ordnance group in theater, the conventional ammunition bat-talion is normally assigned to the COSCOM/
TAACOM (Figures 2-3 and 2-4, pages 2-8 and 2-9) to establish and operate ammunition supply activities. The materiel office
(MATO) of this battalion serves as the initial point of coordination for resolving ammunition support problems. The MATO acts
in concert with the COSCOM staff and CMMC munitions and transportation managers to accomplish the following:
q Coordination of assets.
q Monitoring and cross-leveling of stocks.
q Directing the implementation of COSCOM/TAACOM support operations directives, CMMC/TAMMC taskings, and
CMCC/theater army movement control center (TAMCC) commitments.
The MATO's responsibilities include the following:
q Analyzing CSS/CS data, which interfaces with SAAS to determine trends and efficiency of stock operations.
q Monitoring supply status data on munitions stock at ASAs.
q monitoring RSR, CSR, ammunition basic load (ABL), quantity on hand, and movement requirements data.
q Assisting in synchronizing activities of subordinate ammunition units with habit-ually supporting truck companies.
2-20
FM 9-6 Chapter 2
q Providing technical assistance and monitoring quality assurance, ammunition surveillance, and ammunition maintenance
programs of subordinate units.
q Coordinating with the COSCOM/ TAACOM on cross-leveling munitions support personnel and equipment.
q Recommending to the COSCOM/ TAACOM that, when in-transit, ammunition stocks should be diverted based on
METT-T.
Division
Materiel Management Center
The DMMC is part of the DISCOM (see FM 63-2 , Chapter 3). The munitions supply section of the DMMC manages ammunition
for the division. The DAO is in charge of the munitions supply section. Its mission includes the following:
q Providing technical assistance on all ammunition-related matters to the division staff and units.
q Assisting the division, brigade, and battalion commanders in determining RSRs and implementing CSRs.
q Managing ammunition and provid-ing status of ammunition to the DISCOM and other division commands and staffs.
q Providing staff supervision of FSB ATPs.
Division
Ammunition Officer
The DAO is responsible for ammunition resupply for all units operating in the division AO. He represents the MMC and DISCOM
commander on all ammunition-related mat-ters. The DAO has five broad missions:
q Consolidating division ammunition requirements.
q Preparing plans and procedures for ammunition operations.
q Maintaining ammunition stock records and reports (Standard Army Ammu-nition System-Modernization [SAAS-MOD]
data entry point). (See Appendix.)
q Conducting and supervising ammu-nition operations.
q Validating ammunition requests.
The DAO maintains liaison with the ASA supporting the division and with ammu-nition staff officers at the COSCOM.
Brigade S3
The brigade S3's ammunition responsi-bilities include:
q Determining brigade ammunition requirements based on input from subordi-nate battalions and knowledge of upcoming
tactical operations.
q Determining consolidated brigade RSR and submitting it to the division G3 and DAO.
q Determining the best location for the BSA.
Brigade S4
The brigade S4 ammunition responsi-bilities include:
q Coordinating an issue schedule with the support operations office, FSB, and the DS ammunition company ATP.
q Providing a unit issue priority list to the DAO. Forwarding the consolidated unit ammunition requirements to the DAO.
q Providing subordinate battalion S4s with their allocations of the brigade CSR. (This information is also provided to the
DAO so battalion units do not exceed their authorizations when transloading at the ATP.)
Forward Support
Battalion
The Class V section of the FSB supply company operates one ATP in the BSA. It provides area support to division and corps
units. Each ATP has DAO representatives assigned to control the flow of ammunition.
When munitions arrive at the ATP, the FSB Class V section inspects, inventories, and signs for the shipment. A copy of the
shipping document is returned to the originating ASA. The DAO representative forwards a copy of the receipt document to the
DMMC.
The brigade S4 coordinates with the FSB support operations officer to establish an issue schedule. When supported units arrive at
2-21
FM 9-6 Chapter 2
the ATP, they submit ammunition requests that have been authenticated by the battalion S4. Before a unit is issued ammunition,
the DAO representative at the ATP vaUdates the request. Once ammu-nition is issued to a unit, the unit assumes accountability
and uses its transportation assets to move the ammunition forward.
2-22
FM 9-6 Chapter 3
CHAPTER 3
MUNITIONS PLANNING AND EXECUTION
PURPOSE AND SCOPE
The object of the munitions distribution system is to provide munitions at the right time, place, and
quantity to ensure the success of an operation. Munitions planning and operations must be versatile. They
must complement combat plans and operations and improve the ability of the supported unit to
accomplish its mission.
The supported commander' s concept of operations, priorities, and allocations dictates the actions of the
ammunition planner. Am-munition planning includes:
q Determining ammunition require-ments.
q Echeloning capabilities and ammuni-tion units.
q Establishing split-based operations.
q Preconfiguring ammunition basic loads and resupply amounts.
q When required, using civilian con-tractor, allied, and HN capabilities.
CONVENTIONAL AMMUNITION ALLOCATIONS
The Deputy Chief of Staff for Opera-tions and Plans (DCSOPS) is responsible for developing munitions
programming and budgeting requirements. Requirements determination establishes what is essential to
support a strategy, campaign, or operation. During a conflict, resupply quantities must constantly be
reviewed and adjusted based on historical usage data gathered as the conflict progresses.
Operational Planning
Factors
The United States Army Combined Arms Support Command (USACASCOM) validates munitions
operational planning factors. The Deputy Chief of Staff for Logistics (DCSLOG) is the approving
agency. An automated tool called the Operational Logistics (OPLOG) Planner is the authorized method
for determining munitions planning data at all levels. FM 101-10-1/2 is not an authorized tool for
determining operational ammunition planning factors.
Ammunition consumption rates for all operations, including SASO, are determined using the OPLOG
Planner. Units base their ammunition requirements on METT-T, their projected mission, and the
supported commander' s concept of the operation and intent. Developing ammunition requirements for
using units is the responsibility of their operations section. To obtain the OPLOG Planner software, write
to:
Force Development Division
DIR OF CBT DEVS CBT SVC SPT
3-1
FM 9-6 Chapter 3
700 Quarters Road Suite 210
Fort Lee VA 23801-1703
Ammunition Basic Load
Ammunition basic load is that quantity of ammunition either allocated to or issued to (depending on the
major Army command's [MACOM's] policy) a unit to sustain its operations in combat until it can be
resupplied. Basic load requirements are based on unit weapons density and mission requirements. Units
must be able to transport ABL using organic vehicles, equipment, and personnel.
Munitions Control
Procedures
To sustain tactical operations for specific periods, units determine their munitions requirements and
submit an RSR. The RSR is the amount of ammunition a maneuver commander estimates will be needed
to sustain tactical operations, without ammunition expenditure restrictions, over a specified time period.
The RSR is expressed as rounds per weapon (on hand) per day, or as a bulk allotment per day or per
mission.
RSR computation and routing are normally done by unit S3/G3s. As such, it is not a logistics function,
but the S4/G4 may be called on to assist in the process. RSRs can be computed using manual or
automated procedures. Weapons density (WD) and mission are key to determining RSR. Determine RSR
using the following formula:
Total Rounds =
WD X Expenditure Rate x Days
RSRs are developed by maneuver commanders and submitted to the next higher headquarters.
Headquarters at each level review, adjust, and consolidate RSR information and forward it through
command channels. The ARFOR determines the CSR by comparing the total unrestricted ammunition
requirements against the total ammunition assets on hand or due in.
Several factors limit the amount of ammunition available for an operation (e.g., stockage or lift
capabilities). Accordingly, ammunition issues are controlled by CSRs. The ARFOR establishes the CSR,
which is based on the amount of munitions available for issue. When a munitions item is in short supply,
the CSR is low. The commander determines who receives the ammunition. The DAO informs the G3 of
the quantity available.
The ARFOR commander gives the corps commanders the CSR for each ammunition item. The CSR may
vary from corps to corps based on the mission objectives and priorities of each corps, the projected
threat, and ammunition availability. The corps gives subordinate combat commanders their unit CSR.
Each combat commander gives the CSR to each subordinate combat commander. Commanders making
CSR allocations to subordinate units should retain a portion of the CSR to meet unforeseen
contingencies. The CSR is disseminated to units through the OPORD. The CSR should appear in the
OPORD in paragraph 4, or in either the service support or fire support annex.
The ammunition requirements of other services and coalition members must be considered when
computing the RSR and CSR. Also, ammunition items in the Army inventory that are unique to other
services or coalition members must be considered in supply rate computations. Figure 3-1 illustrates the
3-2
FM 9-6 Chapter 3
flowofRSRsandCSRs.
LOGISTICS PREPARATION OF
THE THEATER
At the strategic level, logistics prep-aration of the theater (LPT) combines the peacetime actions taken by
logisticians at all echelons to maximize means (e.g., force structure, resources, and strategic lift) of
logistically supporting the commander's plan.
xxxx
CSR
RSR
XX
FIRING
UNITS
XXX
CSR
RSR
FIRING
UNITS
Figure 3-1. Ammunition supply rate flow
For the ammunition planner at DA, planning is based on the Defense Planning Guidance (DPG). The
DPG provides scenarios that are modeled and integrated into Army force structure, budgeting,
procurement actions, and operational plans (OPLANs). Ammunition planning at the DA level considers
the following:
q Mission synchronization.
q Threat capabilities.
q Production base.
q Transportation assets.
q Consumption rates determined by the US Army Concepts Analysis Agency (USACAA).
q Depot stocks.
q Prepositioned stockage afloat.
q Worldwide ammunition stocks.
q Echeloning of units using time-phased force deployment (TPFD).
3-3
FM 9-6 Chapter 3
At the operational and tactical levels, logistics preparation of the battlefield is as critical as intelligence
preparation of the battlefield (IPB). Some products generated under IPB should become a part of the data
file of logistics essential elements of information. The ammunition planner uses the tactical commander's
mission analysis to ensure a complete understanding of what must be accomplished. The ammunition
planner participates in the orders process by preparing the munitions piece of the logistics estimate.
Movement
The logistics planners supporting the ASCC and geographic combatant commander must consider total
force ammunition requirements when planning for the movement of stocks and support forces. The
number of HLPs in a theater must be considered prior to requesting containerized ammunition. For more
information on this aspect of planning, see FM 100-16 .
Communications
Ammunition units must have reliable communications to accomplish their mission. Effective
communications networks must be established to ensure the success of ammunition support in the theater
of operations. These networks must relay accurate and timely information between supported and
supporting units, the MMCs, and the DAO. Also, they must interface with the combat and combat
support networks of units supported by ammunition units. The most critical link is the one between the
accountable SAAS level and those responsible for stock status reporting. This link provides necessary
data to the ASCC, enabling crucial decisions to be made in support of the combat force.
Joint Operations
Joint integration of ammunition support is crucial to unity of effort. Army ammunition units will support
the requirements of other services during joint operations. In computing the RSR/CSR, these
requirements must be forecasted and considered. Failure to plan for this support may result in severe
shortages of critical ammunition items and handling capability.
Plans must consider efficiencies gained by having integrated ammunition support. The plans must be
coordinated with the various services involved to ensure adequacy of personnel, storage requirements,
MHE, accountability procedures, and safety.
Combined and Coalition
Operations
Combined and coalition logistics operations (see FM 100-7 ) require integration for unity of effort.
Procedures for ammunition support must be worked out during the planning phase of a deployment or
operation. This ensures interoperability and that handling capability is available. During emergency
deployments, there may not be time to develop formal intercountry agreements. Planners must develop
methods to preclude competition for resources, particularly infrastructure and LOCs, that could adversely
affect operations.
Planners should consider options for contracting, acquiring host nation support (HNS), or obtaining
support from other national forces, and then integrating this support into the multinational force.
3-4
FM 9-6 Chapter 4
CHAPTER 4
RETROGRADE OPERATIONS
PURPOSE AND SCOPE
During operations Just Cause, Urgent Fury, Desert Storm/Desert Shield, and Joint Endeavor, liuge
amounts of munitions were requisitioned and issued to deploying forces. A large part of these munitions
was not expended, and the stockpile that resulted placed an enormous strain on the ammunition support
system. To reduce this burden, retrograde operations must be included in the initial planning of every
exercise and operation-not when the exercise/operation is drawing to a close. Planning and responsibility
for retrograde operations depend on the theater. Based on mission requirements and characteristics of the
force to be supported, responsibility can range from an ammunition group to a platoon.
Another critical issue is soldier casualties from improper handling and repackaging of munitions. Leaders
often fail to enforce discipline during the unpacking, restoration, and reconstitution of ammunition. Also,
leaders do not maintain accountability of the packing materials needed to carry out retrograde operations.
This chapter provides information on what leaders must do to return ammunition to a serviceable
condition upon termination of a conflict. Well before the operation ends, leaders must develop plans
outlining retrograde procedures. These plans must identify the tasks required to return ammunition to its
original packing configuration.
REDEPLOYMENT AND RETROGRADE
Upon completion of combat operations or SASO, the tedious job of identifying, preparing, repackaging,
requisitioning, collecting, loading, and shipping ammunition begins. These tasks constitute the
redeployment process and signal the start of the munitions retrograde program within the ammunition
supply system.
To ensure effective retrograde operations, leaders must enforce supply discipline during the initial
unpacking of ammunition. This includes maintaining salvage and packing materials to be used in
retrograde. Tremendous resources are needed to restore and repackage ammunition. Besides indigenous
assets, contractor and HNS may be required.
Before a redeployment begins, and while combat operations are raging, logistical planners monitor the
levels of munitions in the theater. They then estimate the packing materials needed to retrograde
munitions from the using unit, through ammunition storage activities, to a theater depot or port, and to a
CONUS depot.
During retrograde operations, munitions units continue to provide munitions to security forces while
relocating the excess to a CSA or TSA. To support forward units, CSAs prestock limited amounts of
munitions behind selected division security forces. Surplus stocks are consolidated and shipped to
CONUS or diverted to support other operations. ASPs should contain only those stocks needed to
4-1
FM 9-6 Chapter 4
support security forces, making unnecessary the retrograde of munitions from the ASPs.
Retrograde Planning
Operational planning incorporates a vast array of critical issues and concerns. One of the key issues
planners must address during the initial phases is how to recover and retrograde ammunition remaining
after the operation or exercise ends.
Redeployment plans differ significantly from the deployment plans made before leaving CONUS.
Personnel, time, equipment, and materiel become more important when the main effort is directed at
returning personnel and equipment to CONUS as quickly as possible. At a minimum, planners should
consider the following:
q Begin planning before the last battle.
q Develop a retrograde system that consolidates materiel at various stages; e.g., at unit level to return
to an ATP area.
q Assign condition codes as far forward as possible. Also, make decisions about which ASP should
get certain items for further consolidation or reconditioning.
For planning purposes, assume the following about the condition of munitions in a unit's or soldier's
possession:
q Munitions have been removed from original packing.
q Packing materials have not been retained by the users.
q Munitions will require a service-ability or classification inspection.
At all levels, plans must incorporate retrograde operations. These plans should include:
q Retrograde responsibilities of headquarters, MMCs, supporting ammu-nition units, and using
units. Responsibilities encompass reporting requirements, pack-aging, storing, consolidating, and
security.
q Obtaining and providing empty storage containers, as well as other materials needed to build and
repair pallets and containers.
q Forming retrograde planning cells.
q Identifying special requirements for classified. Category I, or critical sensitive items.
q Contacting USAMC to request specialized teams or personnel to assist in retrograde.
q Responsibilities for recovery of packing materials.
During the various stages of buildup and actual conflict, arrangements must be made for the recovery and
storage of packing materials. These materials can occupy an extraordinary amount of space. They can be
backhauled to a central location or stored in a separate area near the CSA, or in any other area having the
capability and capacity.
The following factors should be considered before actual retrograde operations begin:
q Existing facilities,
q Existing logistical support,
q Shipping point from theater.
4-2
FM 9-6 Chapter 4
q Available HN support.
q Available Logistics Civilian Aug-mentation Program (LOGCAP) support.
Visibility and accountability must begin at the returning unit level. If it has not, then it must begin at the
ATP/ASP level. This is particularly true with Category I and serial-numbered items.
Accountability problems increase during war; however, as much as possible, the accountability of
packing materials must be maintained. If this is done successfully, shortages will be easier to identify and
correct.
Generally, packing materials used by opposing forces should not be used; they can be misidentified and
usually are not of the proper size or quality for US items. How-ever, they can be used for retrograde of
captured enemy items.
When retrograded munitions reach the designated ASA, they must be accounted for, reconfigured,
repackaged, and assigned a condition code. A QASAS or other qualified person must make condition
code decisions.
If proper packing materials are not available, munitions must be inspected to determine their
serviceability. If the munitions are in serviceable condition but have no lot number, a local lot number
may be assigned. These munitions are considered as serviceable.
During retrograde operations, unserv-iceable munitions are typically destroyed. The responsible
ammunition company must request disposition instructions through the MMC to the USAMC before
destroying the munitions.
Captured enemy ammunition (CEA) must be kept separate from US munitions, accounted for, stored,
and guarded using the same criteria that apply to US munitions.
If contractor/HN support is to be used for retrograde operations, it must be negotiated early in the
operation. Contractors must know and fully understand the scope of work necessary to complete the
mission. HNS should be thoroughly screen-ed by security personnel to ensure clearances are granted and
the correct US/HN ratio is negotiated before work begins.
During retrograde operations, leaders must ensure safety policies and procedures are carefully observed.
These operations can be particularly hazardous for the following reasons:
q Careless attitudes may prevail. Absence of battle and relief that the operation is over may cause
soldiers to become so relaxed they become careless.
q Collection of battlefield souvenirs may include dangerous unexploded ordnance (UXO).
q Taking dangerous shortcuts may result in serious injury. As above, the absence of battle and the
excitement soldiers experience at thoughts of going home may contribute to lax behavior,
including the careless handling of ammunition and explosives.
Once ammunition has been inspected, repaired, repackaged, and deemed serviceable or unserviceable by
surveillance personnel, it must be retrograded out of the theater.
DESTRUCTION OF
AMMUNITION
4-3
FM 9-6 Chapter 4
Commanders must follow applicable environmental regulations when destroying munitions. Failure to
obey environmental laws and regulations may subject commanders to fines and/or imprisonment. For
more information, see Chapter 6, Section I, of this manual; FM 20-400 (projected publication, FY 98);
and TC 5-400 .
The two categories of ammunition destruction are routine and emergency. Routine destruction occurs
during normal day-to-day operations (for example, the destruction of unserviceable ammunition).
Routine Destruction
The destruction of ammunition is based on METT-T. However, a general plan for the destruction of
unserviceable ammunition and CEA must be prepared for every storage activity. The destruction site
should be carefully selected so that explosive fragments, debris, and toxic vapors do not become a hazard
to personnel, materiel, facilities, or operations. For more information on selecting a destruction site, see
FMs 5-250 and 9:13 and TM 9-1300-206 .
Ammunition personnel must receive permission from their chain of command before destroying
unserviceable ammunition. Ammunition destruction should be supervised by a QASAS. For information
on the emergency destruction of storage sites, see FM 9-13 , TM 43-0002-33 , and the field SOP.
At the segregation area, unexpended ammunition is identified and segregated by type and lot number,
checked for nonstandard or hazardous conditions, and repacked or palletized and stored lAW distances
outlined in TM 9-1300-206 . In established theaters of operation, surveillance activities are controlled by
QASASs. QASASs inspect and classify ammunition and its components during movement, storage, and
maintenance operations. Also, they inspect equipment, facilities, and operations. A 55B sergeant first
class (SEC) or above, or a QASAS, visually inspects all opened ammunition and determines the
serviceability of both the ammunition and its containers. Also, inspectors must check for compatibility
and ammunition in a hazardous condition.
Added precautions should be taken when handling ammunition containing depleted uranium (DU). (See
TB 9-1300-278 .)
Emergency Destruction
Emergency destruction of ammunition prevents the ammunition from being captured by enemy forces.
Only division commanders and above have the authority to order the emergency destruction of
ammuni-tion. This authority may be delegated to subordinate commanders. TM 43-0002-33 is the
reference for emergency destruction of ammunition.
If it is necessary to conduct emergency destruction operations, the ammunition must be rendered
unserviceable. When possible, emergency destruction should be planned and conducted to impede enemy
troop movements without creating hazards to friendly troops.
The first priority for emergency destruction is classified ammunition and its associated documents. The
second priority is ammunition that the enemy could immediately use against friendly forces, such as hand
grenades or land mines. Also second priority is any ammunition that the enemy could use in their
weapons.
AMMUNITION
4-4
FM 9-6 Chapter 4
MAINTENANCE
To ensure that ammunition is returned to a high state of readiness, maintenance must sometimes be
performed after it is inspected. Maintenance operations include minor packaging and preservation
operations (PP), such as:
q Cleaning.
q Minor rust and corrosion repair.
q Repair and replacement of boxes and crates.
q Restenciling of containers.
q Desiccant replacement.
Maintenance may also include major operations, such as complete renovation. Units should be prepared
to perform as much PP as possible to maintain ammunition in a serviceable condition. In most cases,
ammunition that becomes unserviceable will require evacuation or retrograde to a depot. However, since
the movement of ammunition involves not only safety but also tremendous tonnages, it is not possible to
adopt a maintenance policy geared totally to evacuation. Ammunition determined to be unserviceable
must be reported on an Ammunition Condition Report (ACR), DA Form 2415 , and disposition
instructions requested. Ammunition reported on an ACR should be tagged and segregated pending final
disposition. Ammunition coded Condition Code H will be stored in a separate location pending
disposition. Condition Code H ammunition that poses an immediate threat may be destroyed prior to the
receipt of disposition instructions.
All units that have ammunition on hand, including using units, perform organizational maintenance with
technical assistance from ammunition units.
Ammunition units will perform PP operations as required to prevent further ammunition deterioration. If
added maintenance is required, it will be accomplished as determined by the National Maintenance Point
(NMP). All maintenance operations are performed according to a maintenance SOP derived from TM
9-1300-250 under the supervision of a qualified ammunition inspector as approved by the commander.
Ammunition maintenance is discussed further in Chapter 6, Section IV of this manual.
PHYSICAL SECURITY
When the war is over, the enemy threat changes. Even though the enemy has been officially defeated,
there may be pockets of resistance, guerrilla units, or terrorists that want to continue the fight. Leaders
must keep this in mind and develop effective physical security plans to prevent the capture or destruction
of munitions stocks. Follow guidance in AR 190-11 and FM 19-30 for physical security of ammunition
and explosives.
MPs provide security on an area support basis. However, commanders of ammunition units must ensure
that their unit has devel-oped an effective security plan based on applicable regulations, command
directives, and the tactical situation. At a minimum, the plan must include the following:
q Unit mission.
q Current tactical situation.
q Level of threat expected.
4-5
FM 9-6 Chapter 4
q Available resources,
q Unit vulnerability.
The security plan must consider all aspects of physical security. These include:
q Access control,
q Guard force operations,
q Personnel screening,
q Document and materiel account-ability,
q Emergency actions.
Particular care must be given to provid-ing security for Category I and II munitions items. AR 190-11
contains the guidance required to secure properly Category I and II munitions.
Category I includes non-nuclear missiles and rockets in a "ready to fire" configuration. Also, it includes
explosive complete rounds for these missiles, such as the Stinger, LAW, and AT-4.
Category II includes high explosive and white phosphorous hand and rifle grenades, antitank and
antipersonnel mines with an unpacked weight of 50 pounds or less, and demolition explosives.
TRANSPORTATION
AND STORAGE
When transporting or storing ammuni-tion and explosives for retrograde, use the same precautions and
procedures used for these munitions during the buildup. Theater/corps trucks retrograde munitions stocks
to designated locations. The CMCC/TAMCC regulates all highway movement during the retrograde
operation. It identifies evacuation routes, publishes movement schedules, and designs a battlefield
circulation plan. The theater/corps transportation system will be severely taxed by the movement of units,
supplies, and equipment, and the CMCC/TAMCC may need to request added transportation from HN or
theater transportation assets.
The ASCC, theater movement control agency (TMCA), and transportation command (TRANSCOM)
coordinate with HQDA agencies and the NICP for instructions on relocating ammunition to CONUS or
other theaters for subsequent operations.
Containers and
Packing Materials
AS As normally are the primary consolidation hubs for turned in or backup ammunition storage
containers and packing materials. Also, materials for building or repairing pallets and storage containers
are consolidated at this location.
Retrograde Turn In
Using units normally return munitions identified for retrograde to the ASA that provides their
ammunition support. However, because of the changing requirements of the modern battlefield, units
may be directed to turn in the identified ammunition and explosives to the nearest ASA. ASAs collect,
consolidate, and ship this ammunition as directed.
4-6
FM 9-6 Chapter 5
CHAPTER 5
EXPLOSIVE ORDNANCE DISPOSAL
SUPPORT STRUCTURE
OVERVIEW
EOD support is designed to detect, identify, render safe, recover, evacuate, and dispose of items of
unexploded US and foreign ordnance. This chapter defines an EOD incident, explains how response
priorities are established, and introduces the EOD support structure. For more on EOD force structure, see
FM9-15 .
EOD ROLE
The mission of EOD is to support the national security strategy during peacetime, wartime, and SASO by
reducing or eliminating the hazards of explosive ordnance that threaten personnel, operations, installations,
or materiel.
In all operations, EOD participates in security and advisory assistance, anti-terrorism, counterdrug
operations, training, ordnance disposal, arms control, treaty verification, and support to domestic civil
authorities. Many of these tasks are routinely performed in CONUS and include the following:
q Providing EOD support to the United States Secret Service (USSS) and other federal agencies for
presidential and VIP protection.
q Advising and assisting the civil authorities in the removal of military ordnance that threatens public
safety. See AR 75-15 for authorization information.
q Examining, identifying, and report-ing new and unusual explosive ordnance for technical
intelligence purposes.
q Supporting nuclear and chemical weapons shipments.
q Conducting range clearances. EOD supports range clearance operations by disposing of UXO on
impact areas.
q Destroying ammunition (see FM 9-15) .
q Neutralizing of government- owned ordnance shipments (see FM 9-15) .
q Responding to improvised explosive devices (lEDs).
q Advising on mines and minefield clearance. Mines and minefields are not specifically an EOD
matter. EOD personnel give technical advice and assistance when asked and when priorities allow.
Large-scale minefield breaching is an engineer function.
q Supporting the cleanup of UXO from formerly used defense sites and active installations.
q Providing instruction to host or allied nation military or civilian EOD person-nel on UXO hazards
and disposal techniques.
During war, preserving the com-mander' s combat power becomes more challenging for EOD because of
5-1
FM 9-6 Chapter 5
the increasingly complex and lethal battlefield. EOD integration into staff planning must be sufficiently
explicit to provide for battle synchronization, yet flexible enough to respond to change or to capitalize on
fleeting opportunities. EOD command and control itself must respond quickly and adapt to the rapid
changes on the battlefield.
UXO, including improved conventional munitions (ICMs), is emphasized now more than ever before
because of its potential negative impact on the commander' s combat power. ICMs (because of their sheer
numbers, various means of functioning, and enhanced lethality) have significantly impacted EOD efforts to
preserve the commander' s combat power and provide a safe operational environment for all friendly forces
on the ground. EOD missions include:
q Detecting UXO hazards.
q Identifying unexploded US and foreign ordnance.
q Rendering safe UXO.
q Recovering UXO for technical intelligence exploitation.
q Disposing of UXO.
q Advising commanders on UXO hazards and protective measures.
EOD provides the force projection Army with rapidly deploy able support for the elimination of UXO from
any operational environment. EOD serves as a combat force multiplier by neutralizing UXO that is
restricting freedom of movement and denying access to supplies, facilities, and other critical assets. For
detailed information on EOD support, see FM 9-15 .
EOD INCIDENTS
An EOD incident occurs when a unit detects or suspects the presence of UXO or damaged ordnance that
presents a hazard to operations, installations, personnel, or materiel. Anyone can detect and report an EOD
incident through command or operations channels.
the operations officer at either the corps tactical operations center (CTOC) or TAACOM operations center
prioritizes EOD incidents according to the priorities established by the corps or ARFOR. (For example, a
Priority 1 asset may be an ASP and a Priority 2 asset, a POL point.) Once incidents have been prioritized,
they are referred to the EOD staff officer.
Upon receiving the incident list, the EOD staff officer assigns each incident a category designation. The
EOD categories are as follows:
Category A. Incidents that constitute a grave and immediate threat: "war- stoppers." These incidents are first
in priority for EOD support.
Category B. Incidents constituting an indirect threat.
Category C. Incidents constituting little threat.
Category D. Incidents constituting no threat at the present time.
The priority and EOD category assigned each incident together determine the order in which the incidents
will be handled.
The EOD staff officer forwards the incident workload list to the supporting EOD battalion. The EOD
5-2
FM 9-6 Chapter 5
battalion, in turn, assigns the incidents to its subordinate companies for elimination of the suspected UXO
hazards.
CONTROL PROCEDURES
The limited EOD assets available to the commander are force multipliers that far exceed their actual
numbers. For that reason, EOD operations must be controlled in a manner that has the greatest impact on
supporting the commander' s mission, centralized control and decentralized control are the two methods of
controlling the operations of EOD units.
Centralized Control
Centralized EOD control relies on good communications and a complete and accurate evaluation of the
threat to the war effort. Once the EOD battalion receives the request for EOD support (relayed through the
TAACOM or corps command post from the requesting unit's operations channels), the EOD battalion
assigns the incident to an EOD company. The EOD company then dispatches an EOD response team to
handle the incident. Figure 5-1 illustrates centralized EOD incident reporting.
Decentralized Control
Decentralized EOD control is used most often in peacetime operations. A unit needing EOD support
requests that support directly through operational channels. The EOD company receives the request,
notifies the EOD battalion, and dispatches a response team. Decentralized control works well in peacetime
or when there is no requirement for a massive response by a large number of EOD assets to a major
incident (e.g., a large-scale attack with denial-type munitions on a key facility).
The decentralized method depends less on total area communications than does the centralized method.
With good communi-cations, the centralized method is more flexible and responsive to changing
situa-tions. If communications support is not reliable, and massing EOD assets is not required, the
decentralized method is best since it is less vulnerable to communications failure. With the decentralized
method, each subarea can operate independently while the EOD battalion monitors the reported incidents.
Figure 5-2 illustrates decentralized EOD incident reporting.
TRANSITION
TO WAR
Assigned EOD assets must be incorpo-rated into the war plans of separate divisions, corps, and
TAACOMs. This includes coordination with rear area operations center (RAOC) and HN EOD units. Also,
planning must include coordination between peace-time CONUS EOD units and their wartime OCONUS
higher headquarters.
SUPPORT STRUCTURE
AND OPERATIONS
EOD support is provided geographically to units both in and passing through the area. Also, support may
be provided for maneu-vers by assigning or attaching EOD units to maneuver forces.
User Level
Support
Any unit can report an EOD incident through operational or command channels to a central operations
5-3
FM 9-6 Chapter 5
center. The center can be a division tactical operations center (DTOC), CTOC, or the TAACOM operations
center. The center' s operations officer, with assistance of the EOD staff officer, sets the priority of EOD
incidents based on the threat posed by the incident. Incidents are coordinated, based on the operational
mode used, through the EOD battalion or company for the assignment of an EOD response team. Lastly,
the EOD response team is dispatched to the scene.
EOD Response
Team
Basic EOD support is normally provided by a two- (light) or three-person (heavy) response team organic to
an EOD company. The team may function independently of the parent company for up to 72 hours before
returning to the company. Also, several light teams can be grouped to work on large multi-UXO incidents
or other high priority incidents. If required, a response team may be attached temporarily to a unit other
than its parent company for rations, quarters, and logistical support. However, command and control
remain with the parent company.
A responding EOD team may need added support (e.g., engineers, medical) to reduce potential and/or
actual hazards. The responding EOD team will advise if added support is needed and what type is required.
EOD Company
The EOD company provides command and control for its organic EOD response teams. The mission of
EOD companies is to provide EOD support to corps and TAACOM units. In the TAACOM, they provide
DS to the ASG by covering the ASG area of operations and all units within it. Any EOD companies not DS
to the ASG will be in GS to the TAACOM.
In the corps, EOD companies are positioned throughout the CSG AO and are normally collocated and
attached to the CSBs. Command and control remain with the parent EOD battalion. EOD companies
provide GS to the corps on an area basis and can be placed in DS of a specific maneuver unit, normally a
division or task force equivalent element.
Because of limited personnel and equip-ment assigned to an EOD company, the company depends on the
unit to which it is attached or supporting for rations and administrative and logistical support. EOD
companies have a limited number of personnel available for base security and other details.
EOD Company
(CONUS-Based)
The CONUS-based EOD company provides command and control for its organic EOD response teams. Its
mission is to reduce or eliminate the hazards of munitions and explosive devices throughout the continental
United States.
This company provides EOD service on an area basis for a maximum routine incident response capability
of 120 incidents per day (based on 12 teams). Also, it may respond to civilian requests for EOD support
and assist public safety and law enforcement agencies in handling lED and terrorist threats. The
CONUS-based EOD company may provide support to other federal intelligence agencies as outlined in
DOD directives and support installations by clearing ranges and destroying unserviceable ammunition.
5-4
FM 9-6 Chapter 5
CORPS /TAACOM
SEPARATE DIVISION
OPERATIONS CENTER
il
EOD GROUP
u
EOD
BATTALION
LIGHT
RESPONSE
TEAM
EOD
COMPANY
HEAVY
RESPONSE
TEAM
LIGHT
RESPONSE
TEAM
\
EOD
COMPANY
RESPONSE TEAM DISPATCH
SECURE COnmUNfCATIONS
NOTfFfCATfON
5-5
FM 9-6 Chapter 5
Figure 5-1. Centralized EOD incident reporting
CORPS /TAACOM
SEPARATE DIVISION
OPERATIONS CENTER
EOD GROUP
BATTALION
USER
EOD
COMPANY
LIGHT RESPONSE
TEAM
HEAVY RESPONSE
TEAM
LIGHT RESPONSE
TEAM
4
1
EOD
COMPANY
:s"
RESPONSE TEAM DISPATCH
SECURE COnmiUNICATIONS
NOTIFICATION
Figure 5-2. Decentralized EOD incident reporting
EOD Battalion
An EOD battalion provides command and control for three to ten EOD companies. A battalion with eight
EOD companies is allocated to a TAACOM. A corps is allocated one EOD battalion with ten subordinate
EOD companies.
The EOD battalion has a limited number of personnel and equipment. Therefore, it is dependent on the unit
to which it is assigned or attached for rations and administrative and logistical support.
Ordnance Group (EOD)
The ordnance group (EOD) has two major functions: theater EOD planning and EOD command and
control. This group is composed of two to six EOD battalions.
User Level
5-6
FM 9-6 Chapter 5
Support
Any unit can report an EOD incident through operational or command channels to a central operations
center. This center can be a DTOC, CTOC, or the TAACOM operations center.
The center's operations officer, with the assistance of the EOD staff officer, sets the priority of EOD
incidents. Priority is based on the threat posed by the incident.
Incidents are coordinated, based on the operational mode used, through the EOD battalion or company for
the assignment of an EOD response team. Lastly, the EOD response team is dispatched to the scene.
EOD Staff
Officer
The ranking EOD officer serves as the EOD staff officer to the TACOM, TAACOM, corps, or division.
This officer is normally dual-hatted as the respective EOD group, battalion, or company commander.
Responsibilities of the EOD staff officer include the following:
q recommends policy and distribution of EOD assets.
q Monitors incident reports, estab-lishes workload priorities, and serves as POC for technical
intelligence coordination.
q Coordinates EOD support while ensuring that proper communications have been coordinated at each
level supporting EOD operations.
The EOD staff officer and staff are located within the theater army command (TACOM), the TAACOM,
the corps, and wherever a division is deployed as a separate unit. Also, an EOD staff element (joint service)
will be located at the joint, unified, or combined command staff to assist in managing interservice EOD
support.
If no ASCC staff headquarters exists in the theater of operations, an EOD officer and staff are included in
the ARFOR element of a joint, unified, or combined command task force staff to manage Army EOD
operations.
HOST NATION
INTERFACE
HN EOD assets generally have limited chemical or biological expertise and normally no capability for
supporting nuclear weapons accidents or incidents. However, most HN forces do have an EOD
identification capability. When US EOD support is not available, the area damage control cell of the
RAOC interfaces with HN assets to use the appropriate HN EOD assets. If US EOD support is used, it
must be properly coordinated and must comply with government, HN, state, and local requirements. If the
HN does not have environmental laws and regulations, US statutes will apply. Emergency operations or
EOD operations that take place during wartime will adhere to protocols as outlined in the Military
Munitions Rule (MMR).
COMMUNICATIONS
EOD units need a wide range of com-munications to accomplish their mission. Long-range
communications are required among the deployed teams, the companies, the EOD battalion, and the EOD
group. EOD units are linked to the area communications network through mobile subscriber equipment
5-7
FM 9-6 Chapter 5
(MSB). Also, EOD response teams and units require a data processing capability for electronic
transmission of record traffic.
When operating at an incident site, EOD response teams need secure, short-range, wireless interteam
communications for the coordination of team member activities and safety. The response teams dispatched
on the battlefield require a position navigation device with digital data capability for precise location
determination.
5-8
FM 9-6 Chapter 6
Chapter 6
THE ENVIRONMENT, SAFETY, RISK MANAGEMENT,
AND MAINTENANCE AND SURVEILLANCE OPERATIONS
SECTION I. THE ENVIRONMENT
ENVIRONMENTAL POLICY
AND GOALS
Much of the Army' s environmental effort springs from the National Environ-mental Policy Act (NEPA),
Public Law (PL) 91-190 of January 1970. NEPA requires federal officials to analyze potential environmental
impacts of proposed actions and alternatives before making decisions. The law applies to all Army leaders and
activities. Its purpose is to encourage harmony with our physical environment and promote efforts that prevent
or eliminate environmental degradation. Also, it improves understanding of relations between ecological
systems and important natural resources. In line with NEPA requirements, the Army established a number of
policies, programs, and goals to preserve, protect, and restore the quality of our nation's environment.
The Army is also responsible for assisting and complying fully with HN, state, and local laws and regulations.
Local laws and ordinances address the concerns of local communities. Each state has its own regulatory
agency charged with developing and implementing environmental regulations. While many state and local
regulations parallel federal law, they are often more stringent. The Army is committed to the policy that
awareness and consideration of environmental issues are an integral part of our relations with the HN. (Note:
In the event the HN has minimal or no environmental laws or regulations, ARs 200- 1 and 200-2 will apply).
Environmental stewardship calls for awareness and commitment throughout the Army. All soldiers and leaders
must do their part by supporting Army objectives. The Army's environmental goals are as follows:
q Demonstrate leadership in envi-ronmental protection and improvement.
q Provide environmental awareness training, including training in environmental laws and regulations, for
all soldiers.
q Ensure full compliance with federal, state, local, and HN laws.
q Ensure environmental concerns are part of the decision-making process at all levels of command.
q Provide guidance on the duties and responsibilities of unit commanders and individual soldiers as they
relate to environmental stewardship, protection, and compliance.
q Ensure that environmental laws and regulations are followed with maximum emphasis on compliance.
q Incorporate unit-level procedures in SOPs at all command levels.
For added information on Army environmental stewardship, see FM 20-400 (projected publication, FY 98).
Munitions and Army operations have the potential to cause considerable damage to the environment. Thus, the
Army has become a national leader in the areas of environmental and natural resource stewardship. This role is
an integral part of the Army mission for both present and future generations. Concurrent with this
responsibility is the continuing need to exercise extreme caution to prevent accidental damage to the
environment.
6-1
FM 9-6 Chapter 6
STEWARDSHIP
IN THE
OPERATIONAL ENVIRONMENT
In day-to-day CONUS operations, or when coordinating operations within an HN or coalition scenario
OCONUS, commanders must promote and inspire a keen awareness of the environment.
Many federal, state, local, and HN laws hold commanders legally responsible for environmental damage that is
caused by inadequate planning or supervision of operations and training. Penalties can include fines or
imprisonment or both.
To avoid adverse environmental impact when planning or executing operations, leaders must comply with the
provisions of ARs 200-1 and 200-2 , FM 20-400 , 40 CFR, and the guidance for unit leaders contained in other
appropriate manuals.
Providing ammunition in the theater of operations is essential. When doing so, however, leaders must follow
applicable provisions of the Resource Conservation and Recovery Act (RCRA), to include the MMR. The
RCRA establishes the framework for managing hazardous wastes. It sets the standards for hazardous waste
identification, classification, transportation, storage, treatment, and disposal. When munitions or munitions
operations fall under RCRA purview, full compliance includes requirements for permits and storage.
The operational commander determines the need for, and the environmental impact of, destruction of
ammunition or other explosives, to prevent capture by the enemy, or injury to military or civilian personnel,
operational requirements must be applied. Environmental considerations should be followed when time
permits, especially if imminent and substantial danger to the environment exists.
Environmental damage that occurs as a result of enemy actions or accidents involving munitions should be
repaired. Containment, cleanup, and restoration of the immediate area will allow the area to be used for future
operations. Commanders must follow guidance in applicable publications and use environmental
risk-assessment matrices to assess possible damage. Such assessments allow leaders to minimize
environmental damage while optimizing performance and mission completion. Before conducting training,
operations, or logistics activities, a risk-assessment matrix should be completed for each environmental area
listed below:
q Air Pollution.
q Water pollution.
q Noise pollution.
q Archeological and historical sites.
6-2
FM 9-6 Chapter 6
Environmental Area (air pollution, water pollution, noise pollution, archeological and historic
sites, hazardous materials and hazardous waste, threatened/endangered species, wetland
protection).
Rating
UNIT OPERATIONS
RISK IMPACT
Movement of heavy equipment & vehicles
5 4 3 2 1
IVIovement of personnel & light vehicles/
systems
5 4 3 2 1
Assembly area activities
5 4 3 2 1
Field maintenance of equipment
5 4 3 2 1
Garrison maintenance of equipment
5 4 3 2 1
Figure 6-1. Environmental risk-assessment matrix
q Threatened/endangered species.
q Hazardous material and hazardous waste.
q Wetland protection.
See Figure 6-1 for an environmental risk-assessment matrix. TC 5-400 , Chapter 5, discusses risk management
in depth and gives instructions on using the risk-assessment matrix.
Commanders of munitions and munitions support units have specific stewardship and compliance
responsibilities. These go beyond the ones implicit in the Army's environmental goals. They include the
following:
q Ensuring safety throughout the environment.
q Establishing a unit training program geared towards environmental considerations in handling
ammunition.
q Preventing damage and pollution by ensuring existence and application of sound environmental
procedures and practices in daily activities.
q Ensuring munitions are distributed and stored in a manner consistent with sound environmental
6-3
FM 9-6 Chapter 6
practices. This includes ensuring frequent inspections are conducted to detect deteriorating, leaking, or
damaged containers.
q Ensuring compliance with environ-mental regulations during all operations.
q Focusing on prevention of pollution at the source, concurrent with the proper management of hazardous
materials and hazardous waste.
q Focusing maximum attention on the prevention of environmental incidents and accidents by
emphasizing proper training.
q Ensuring that an environmental compliance officer/hazardous waste coordi-nator is assigned in writing.
This person must be properly trained and qualified in environmental matters. Duties should include
coordination and interface with appropriate environmental personnel to ensure unit compliance with
laws and regulations.
Arming the force is perhaps the most important of the five basic CSS functions. Effective and efficient
distribution of munitions within a theater of operations could be the decisive factor in a battle or the war.
Incorporating the environmental ethic and stewardship principles in day-to-day operations and ensuring
compliance may seem at odds with this focus. What we must remember, however, is that where we operate
and fight today may be where we work or live tomorrow.
SECTION II. SAFETY
RESPONSIBILITIES
Safety, including risk assessment (see Section III) and accident reporting, is an inherent responsibility of
commanders at all levels. Its importance is intensified for units and personnel engaged in munitions-related
activities. The following discussion provides guidance on both general and munitions-related safety issues.
Munitions handlers must be alert to the danger associated with depleted uranium rounds. Since these rounds
present a potential radiological hazard, proper storage and handling are critical. See TB 9-1300-278 for
information on the hazards and appropriate safety measures.
All soldiers and leaders must maintain a proactive posture towards safety in day-to-day operations. This
commitment to safety should be evident to seniors, peers, and subordinates. Specific responsibilities of key
personnel and individuals are detailed below.
Commanders. Safety is a command respon-sibility at all echelons. Commanders must display active and
aggressive leadership towards safety issues. They must appoint a safety officer or NCO lAW AR 385-10 and
DA Pamphlet 385-1 . They must determine the causes of accidents and take the neces-sary preventive and
corrective measures.
Safety Officer/NCO. The primary duties and responsibilities of the unit safety officer or NCO include the
following:
q Preparing a unit safety program and a field safety SOP focused on safety awareness (rather than reactive
safety reporting).
q Reviewing regulations and Tms; recommending changes, when needed; recommending procedures for
increasing safety in unit operations in general, as well as in the receipt, handling, storage, trans-porting,
and issuing of munitions.
q Making safety-related suggestions to the commander for review and possible inclusion in unit SOPs.
Leaders. Leaders must ensure that soldiers perform their duties safely by-
6-4
FM 9-6 Chapter 6
q Making soldiers aware of hazards.
q Stressing safety in operations.
q Halting unsafe operations.
q Preventing accidents through pro-active planning and preparation.
Individuals . Individuals are largely respon-sible for ensuring their own safety. This includes:
q Familiarity with the Army's general safety policies for ammunition, explosives, and related operations
(see AR 385-64 and TM 9-1300-206) .
q Knowledge of the basic principles of how munitions work and how to handle and transport them safely.
q Familiarity with hazards and safety precautions that apply to specific munitions. Such information can
be found in FMs and TMs covering various types of munitions.
STANDING OPERATING PROCEDURES
Each unit should have on hand a current, detailed (as much detail as needed) safety SOP. This safety SOP
should include the following:
q Safety education and promotion plans.
q Safety requirements and training frequency.
q Procedures for detecting potential safety violations and ensuring that correc-tions are made.
q Provisions for periodic briefings conducted by the unit command to update soldiers on new munitions
items and technical intelligence reports. This is an effective method of keeping soldiers informed and the
safety awareness level high.
Individual SOPs must be developed for any and all operations where ammunition or explosives are involved.
These procedures must describe the operation in enough detail to enable an untrained soldier to perform the
operation safely. Failure to follow the SOP is the major cause of many accidents involving munitions. In some
cases, no SOP was developed for the operation.
ACCIDENT REPORTING
Besides recognizing and controlling safety hazards, it is essential that the causes of accidents be determined.
This information aids in identifying accident trends, unsatis-factory work performance, personnel losses, and
property damage. All accidents resulting in injury or property damage must be reported.
DA Form 285 is the primary means of reporting accidents. For information on completing this form, see AR
385-40 .
When an accident occurs, it is important to gather all essential information for reports and possible corrective
action. At a minimum, the following information should be included in the report:
q Who was injured or what was damaged.
q Time and place the accident occurred.
q Severity and cost (in personnel or materiel) of the accident.
q Nature of the accident or injury.
q How and why the accident occurred.
Corrective actions are based on specific facts about the accident or injury. They can include removing the
hazards, improving operations, or training personnel. Moreover, corrective action must be supplemented by
6-5
FM 9-6 Chapter 6
proper management on the part of unit leaders. They must ensure that familiarity with operations does not lead
to complacency or contempt for safety awareness.
SECTION III. RISK ASSESSMENT
AND MANAGEMENT
INTEGRATING
ASSESSMENT TECHNIQUES
In peacetime, leaders learn to assess risks during training exercises. Techniques learned in training can then be
used during combat operations. In combat, risks must be taken, but only after the mission is evaluated and
weighed as practiced during training.
Identification of hazards and their possible effects is called risk assessment. Risk management is the
decision-making process that balances operational demands against identified risks. Doing risk assessment and
applying risk management should become fully integrated parts of operational planning and execution.
FIVE-STEP
PROCESS
Risk management is a closed-loop, five-step process that can be used by anyone at any time or place and for
any type of mission. The five steps are as follows:
q Identifying the hazards. Identify all hazards, including hazards to both soldiers and equipment.
q Assessing the hazards. Assess the hazards to determine the risks involved and their impact in terms of
potential loss and cost. Assessments are based, to a degree, on probability and severity.
q Developing controls and making risk decisions. Develop control measures that eliminate hazards or
reduce risks. Continually reevaluate risks during this process. The process continues until all risks are
reduced to a level where the benefits outweigh potential costs.
q Implementing controls. Implement those controls that are determined to eliminate the hazards or reduce
the risks.
q Enforcing and reevaluating controls. Enforce control measures through proper supervision. Constantly
reevaluate the controls to ensure continuing effectiveness or to adjust as needed.
The proper use of risk assessment and risk management procedures is a primary force protection method,
saving lives and protecting equipment from accidental damage and loss is the bottom line.
SECTION IV. MAINTENANCE AND
SURVEILLANCE OPERATIONS
MAINTENANCE
OPERATIONS
Maintenance of munitions includes all actions necessary to ensure that stocks are serviceable, or that
unserviceable stocks are restored to a serviceable condition. Maintenance responsibilities are assigned to
ammunition units based on the unit's primary mission and the availability of personnel, skills, time, tools,
equipment, and supplies.
maintenance operations for DS units are based on METT-T. The preservation, pack-aging, marking, and minor
spot painting of items is standard, situations calling for more than minor maintenance (i.e., PP) are handled and
coordinated through command channels.
6-6
FM 9-6 Chapter 6
Ammunition maintenance planning must be aligned closely with the operational needs of the supported units.
Maintenance planners must consider the availability of supplies and maintenance resources. A decrease in
ammunition maintenance increases the amount of ammunition needed from the supply system.
Conversely, the inability of the supply system to replace unserviceable ammunition requires a greater
maintenance effort. Proper maintenance, as well as the proper storage and handling, of ammunition increases
readiness, reduces supply requirements for replacements, and conserves resources for other purposes. The
maintenance planner must recognize the interdependence of maintenance and munitions support.
Concepts
Combat units must have serviceable ammunition. Maintenance of munitions is a necessary and vital task that
must be performed to maintain a high state of readiness. Maintenance includes minor operations (e.g., cleaning
and rust removal) and major operations (e.g., complete renovation). Provisions must be made to conduct as
much maintenance as possible at the storage location.
In some cases, ammunition must be evacuated for maintenance. However, since the movement of ammunition
consumes transportation assets, it is inefficient to adopt a maintenance program geared totally to evacuation.
DS, OS, and modular units may initiate and conduct maintenance operations and programs when operating in
the corps and theater areas. In these forward areas, maintenance functions are limited to PP operations, such as
replacing broken banding or minor pallet repair or replacement.
Categories
Munitions maintenance is divided into four categories: organizational, DS, GS, and depot. For ammunition
units, DS and GS maintenance is limited to packaging and preservation operations.
Organizational maintenance is per- formed by all activities that have ammunition on hand, including using
units. Organi-zational maintenance in the using unit is usually performed with the technical assistance of
ammunition units.
DS maintenance is performed by ammunition companies in the theater of operations that have DS capabilities.
GS maintenance is performed by ammunition companies in the theater of operations that have GS capabilities.
Modular companies are designed with the capability to perform both DS and GS maintenance.
If items require depot maintenance (such as modification, explosive component replacement, or complete
renovation), the ammunition is packaged and evacuated to a depot.
All DS, GS, and modular companies with storage and issue missions are equipped to perform maintenance
functions. Tools, equipment, and supplies needed to support maintenance are included in each unit's supply
and equipment list.
Standing Operating
Procedures
All maintenance is performed lAW an approved maintenance SOP. See Tm 9-1300-250 for guidelines on
preparing maintenance SOPs. Also, valuable guidance may be available from a unit with similar missions and
responsibilities, or from experienced personnel. When local nationals are involved in maintenance operations,
the SOP must be written in their language as well as in English.
SURVEILLANCE
6-7
FM 9-6 Chapter 6
Ammunition surveillance is the obser-vation, inspection, and classification of ammunition and its components
during movement, storage, and maintenance opera- tions. This definition also covers inspection equipment,
facilities, and operations. Sur-veillance activities are conducted by all theater activities that store, maintain,
dispose of, or ship ammunition and its components. Surveillance ends only when the ammunition is expended
or destroyed.
The TAACOM is responsible for supervising ammunition surveillance in the theater of operations. The CSB or
CSG closely supervises this function in its com-mand. In established theaters of operation, surveillance
activities are under the control of DA civilian (DAC) QASASs assigned to major Army headquarters. In
theater ammunition units, surveillance is performed by attached civilians and assigned military inspectors.
The commander of any ammunition battalion must administer a QA ammunition surveillance program that
covers all ammunition operations assigned to that command. The QASAS in charge has the overall
responsibility for the program and reports directly to the commander. Since QASAS training is much more
extensive than that of the military inspector, the QASAS performs the more complicated inspections and most
functional tests. The QASAS certifies the results of any inspections or tests performed by the military
inspectors. In some commands, certain inspection results and functional test reports can be signed only by a
QASAS.
when in an immature or developing theater, all surveillance functions are performed by 55Bs in a DS, GS, or
modular ammunition company.
Functions
Ammunition inspectors perform the following duties:
q Inspect storage buildings, outdoor storage sites, and field storage sites to make sure that they comply
with all storage standards.
q Inspect surrounding areas for fire hazards and other nonstandard conditions.
q Look for nonstandard conditions that could speed up the normal deterioration rate of the items in
storage.
q Teach surveillance and ammunition safety.
q Prepare and maintain proper corre-spondence, records, and reports to cover all surveillance activities.
See SB 742-1 for a list of surveillance records and reports.
q Observe, inspect, and investigate to determine the current degree of serviceability of ammunition and
components.
q Monitor the methods of storage, handling, and maintenance and recommend changes to increase safety
and operational effectiveness.
q Recommend to commander controls needed to maintain standards of quality.
q Act as technical advisors to the commander on all ammunition surveillance matters.
q Inspect and investigate to determine the quality, safety, and deterioration of ammunition.
q Help investigate ammunition accidents.
q Help plan, coordinate, and administer the explosives safety program. This program includes review,
evaluation, and inspection of all operations, procedures, equipment, and facilities used with ammu-nition
and explosives operations to ensure application of and compliance with pertinent safety standards and
criteria.
q Help plan the construction of storage facilities and/or field storage areas based on current
6-8
FM 9-6 Chapter 6
quantity-distance require-ments and storage criteria.
q Prepare and maintain accurate records of all observations, inspections, and investigations.
q Maintain files and indexes for all drawings and specifications covering ammu-nition and methods of
packing and storing.
q Inspect all incoming and outgoing shipments of ammunition for sabotage devices; proper blocking,
bracing, and loading; condition and serviceability; and compliance with existing instructions and
regulations.
q Inspect dunnage used and storage methods for compliance with specifications, drawings, and safety
regulations.
q Furnish technical advice regarding safety to unit operating elements.
q Ensure all facilities and/or field storage areas comply with existing regulations. This includes
compliance of the methods used to store, handle, ship, assemble, load, preserve, maintain, salvage, and
destroy ammunition.
q Ensure all surveillance functions are performed lAW the procedures set forth in SB 742-1 , applicable
TMs, and other SBs.
Inspections
I AW SB 742-1 , the following surveillance inspections are performed by the QASAS and military inspectors:
q Receipt inspections, including depot transfers, field returns, and CEA.
q Periodic inspections (cyclic),
q Storage monitoring inspections,
q Special inspections,
q Pre-issue inspections,
q Verification inspections,
q Ammunition condition code inspec-tions.
Serviceability Standards
The object of an inspection is to find deterioration and determine the degree of serviceability of the inspected
item. That is, whether the inspected item is serviceable as it stands, requires maintenance, or must be rejected.
Before inspecting an item, the inspector should be familiar with all available information about the item,
including its components, packaging, and the characteristics of the weapon in which it is used. See SB 742-1
for serviceability standards references.
Inspection procedures include observa-tion, physical tests (such as gauging or strength tests), and functional
tests. Unserviceability can usually be detected by casual observation. As a general guide, munitions must not
have any defects that would alter their characteristics, make them unsafe, or make them perform in any way
other than for what they were designed. The inspector must determine whether defects found can be corrected
and at what level this must be done.
The prime enemies of ammunition are heat and moisture. They affect all ammuni-tion components to a varying
degree. Deterioration is faster when moisture is combined with a rise in temperature. Inspectors should be
especially alert to indications of moisture, rust, or corrosion on projectiles and fuses; corrosion and cracks on
cartridge cases; deterioration of propellants; loose closing caps; and moisture or dampness inside containers.
Physical Defect
6-9
FM 9-6 Chapter 6
Standards
Evaluating the acceptability of materiel that shows deterioration or damage depends on the training,
experience, and judgment of the inspector. The deterioration of materiel in storage is natural. However, the rate
and degree of that deterioration vary according to the type of protective coating on the materiel, packaging,
and storage conditions. Also, deterioration is progressive, if no maintenance is performed, the condition
degrades through four stages: incidental, minor, major, and critical. The four stages are used to establish a
uniform system of examination for deterioration or damage.
for added guidance on classifying metal, plastic, and rubber component deterioration; mixed ammunition;
damaged packaging; and for placing defects into one of the four defect categories, see SB 742-1 , applicable
techni-cal manuals, and supply bulletins.
Guided Missiles and
Large Rocket Inspection
Guided missile and large rocket (GMLR) ammunition, components, propel-lants (liquid and solid), protective
clothing, packaging, and packing materials are inspected and tested using applicable SBs, TMs, drawings, and
specifications.
Most mid-size guided missiles are now certified as rounds and are maintained by the contractor at contractor
facilities. Unit maintenance on guided missiles is essentially limited to spot-painting and replacement of wings,
elevons, and the like. Inspectors must check with surveillance to determine those liquid propellants that should
be removed before turn in. Missile items identified by lot or serial numbers are inspected for serviceability as
follows:
q Materiel identified by lot number is sampled and inspected by individual lots. Missiles are inspected
using the inspection table in the appropriate TM or SB.
q Materiel identified by serial number is put into homogeneous groups. This grouping is not a permanent
or physical grouping of the items, but a grouping on paper for inspection. The judgment of a QAS AS or
MOS 55B ammunition specialist is needed in forming these groups.
Defects found in the sample are classified using the applicable SB, TM, or other specification. Where defects
are not classified in these publications, the inspector classifies them according to SB 742-1 . The results of the
sample inspection are used to make serviceability decisions about the lot or group.
SURVEILLANCE
RECORDS AND REPORTS
Surveillance personnel keep a technical history of each lot, serial number, or group of munitions. This history
includes a record of the results of all inspections, tests, investigations, and any unusual or changing conditions
affecting the items. These records are used to evaluate the serviceability and reliability of ammunition items. It
is important that all information gathered from surveillance procedures is accurate and concise. The type of
information needed for recording and reporting purposes may vary depending on the organizations supported
by surveillance. The information needed to satisfy local and higher headquarters supply actions is determined
by local procedures. The information needed for maintenance purposes is usually more detailed as to the extent
of the defect and the work required to return the item to service. The following information is needed to
evaluate the reliability of the stockpile:
q Condition.
q Quantity.
6-10
FM 9-6 Chapter 6
q Date of manufacture,
q Type of storage,
q Type of defects,
q Cause of defects,
q Results of tests.
Surveillance personnel are also required to submit other types of reports on materiel received or in storage and
to maintain certain records. SB 742-1 provides guidance for preparing these records and reports, which are
listed below:
q DP Form 250 (Material Inspection and Receiving Report).
q DP Form 1575 (Suspended Tag -Materiel).
q DP Form 1575-1 (Suspended Label-Materiel).
q PP Form 1650 (Ammunition Pata Card).
q PA Form 984 (Munitions Surveillance Report Pescriptive Pata of Ammunition Represented by
Sample),
q PA Form 2415 (Ammunition Condition Report),
q PA Form 3022-R (Army Pepot Surveillance Record),
q PA Form 3023 (Gage Record),
q PA Form 4508 (Ammunition Transfer Record),
q SF 361 (Transportation Piscrepancy Report),
q SF364 (Report of Piscrepancy [ROP]).
q Ammunition inspection and lot number reports.
q Ammunition suspension records, to include Armament, Munitions, and Chemical Command
(AMCCOM) and Missile Command (MICOM) suspension.
q Equipment logbooks and mainten-ance logs.
q Reports of explosions, chemical agent releases, serious accidents, and nuclear incidents.
q Small arms tracer reports.
q Storage monitoring records (local format).
DESTRUCTION PLAN
The destruction of ammunition is based on METT-T and command guidance. A general plan for the
destruction of unserv-iceable ammunition and CEA must be prepared for every storage activity. At a
minimum, this plan includes the following:
q Priorities of materiel to be destroyed.
q Methods of destruction.
q Location of primary and alternate disposal sites.
q Protective clothing requirements.
q Pec ontamination requirements .
q Required equipment and explosive materials, with instructions for their placement and use.
6-11
FM 9-6 Chapter 6
Also, the destruction plan must consider emergency destruction of munitions. See Chapter 4 of this manual and
TM 43-0002-33 for more information on emergency destruction.
A destruction site should be carefully selected so that explosive fragments, debris, and toxic vapors do not
become a hazard to personnel, materiel, facilities, or operations. For more information on selecting a
destruction site, refer to TM 9-1300-206 and FMs 5-250 and 9-13 .
Ammunition personnel normally perform the routine destruction of ammunition deter-mined to be
unserviceable as a result of damage or deterioration.
UNSERVICEABLE
AMMUNITION STORAGE
Unserviceable ammunition is either manufactured with defects or has been made unserviceable by improper
storage, handling, packaging, or transportation. Shipments of ammunition received from other supply facilities
should be inspected for serv-iceability. When it is not possible to inspect the ammunition at the time of receipt,
unit turn ins should be stored in a segregated area for later inspection. Ammunition specialists should be
familiar with indications of unserviceability and report them.
Unserviceable ammunition must be segregated from serviceable ammunition for safety reasons and to reduce
rehandling. Also, inspectors must segregate the ammuni-tion by DODIC and lot number, followed by
serviceability classification. Ammunition that cannot be positively identified by lot number is automatically
classified as pending disposition (condition code K). Exceptions may be made based on METT-T and the type,
quantity, and condition of the ammunition.
The same safety precautions and principles used for storage of serviceable ammunition are used for the storage
of unserviceable ammunition. Proper records must be kept on all unserviceable items stored at a supply
facility.
Ammunition that requires maintenance should be segregated and marked to prevent issuing. Minor
preservation and packaging are performed at field locations, TSAs, CSAs, or ASPs. Extensive maintenance is
usually performed at a depot storage facility.
The unit packages and preserves the ammunition if that is the only requirement. If time permits, unserviceable
ammunition that is repairable is retrograded for repair. Ammunition abandoned by using units is treated as
unserviceable until it is inspected. The procedures that apply to unit turn-ins also apply to abandoned
ammunition. Unserviceable ammunition is reported through proper channels for disposition instructions.
Hazardous unserviceable ammunition is reported immediately through proper channels to EOD detachments
for destruction. A demolition area is designated and cleared for the safe destruction of ammunition.
SUSPENDED
AMMUNITION STORAGE
Specific lots of ammunition and components are withdrawn from issue when they are determined to be unsafe
or otherwise defective. Storing ammunition by lot number enables the rapid withdrawal from issue of those
items that are unsafe, defective, or suspected of being defective.
The authority to suspend any lot of conventional ammunition is vested in the commander. Industrial
Operations Command (IOC). However, a local suspension may be placed on a suspected lot of ammunition by
the installation or area commander. A preliminary report, and later a detailed report, are forwarded through the
supporting MMC to the ARFOR. The ammunition remains in local suspension unless its status is changed by
higher headquarters. See TB 9-1300-385 for instructions in preparing suspension reports. TB 9-1300-385 lists
6-12
FM 9-6 Chapter 6
suspended lots of conventional ammunition and components. Added notices of suspen-sions or restrictions are
produced as supplemental changes to TB 9-1300-385 , Ammunition Information Notices (AINS), or Safety of
Use Messages (SOUMS).
Ammunition lots that are stored and later placed under suspension need not be moved to a segregated area
unless the suspension notice so orders. Stacks of suspended ammunition must be clearly marked on all sides.
This is done using DP Form 1575 and DA Form 3782 , or facsimile-formatted documents (taped to the
materiel), to show that the items have been suspended or restricted from issue. When foreign nationals are
employed, locally-produced bilingual tags should be used. Suspended or restricted-issue items returned by the
firing units, or items received from other supply facilities, should be segregated upon receipt. These items
should be marked using the forms mentioned above and stored in the segregation area. DA Form 3020-R or a
facsimile-formatted document (taped to the materiel) should be posted showing the suspension date,
suspension number, and authority.
CAPTURED
ENEMY AMMUNITION
STORAGE
Enemy ammunition found is considered excess and is to be treated as such. AR 381-26 requires that one of
three options be taken when ammunition is determined to be in excess for any reason on the battlefield. These
options are use, destroy, or secure and retrograde. Except for use, all of these options apply to CEA. As
discussed in this section, CEA includes all types of munitions.
When an enemy ammunition cache is found or captured, the commander must assess the combat situation. He
must decide whether to destroy the CEA because of the situation, or to secure it and request EOD support. If
the commander notifies EOD, he must provide the following information:
q Grid coordinates.
q Estimated quantity of munitions.
q Initial estimate of the different types of CEA in the cache.
EOD analyzes and identifies the types of munitions in the cache and determines the following:
q If the munitions present a hazard to friendly forces (booby-trapped or nuclear, biological, chemical
[NBC]).
q If the items are safe to transport.
EOD then evaluates the CEA for possible technical intelligence exploitation. If any of the munitions are
identified for technical exploitation, EOD forwards a technical intelligence report to the assistant chief of staff
(intelligence) (G2/J2). The G2/J2 coordinates the evacuation of any of the CEA identified for exploitation.
Also, civilian or military ammunition inspectors may assist in inspecting the cache after EOD has determined
there are no extraordinary hazards (booby-traps, time-delay devices, and/or armed munitions). All hazardous
enemy ammunition should be segregated and disposed of by trained personnel.
If the cache is to be retrograded, ammunition units in the corps are tasked to provide QASAS, MHE, and
ammunition handlers to inspect, segregate, and load the captured stocks. Also, corps transportation assets are
tasked to move the CEA. Working together, these corps assets load and transport the CEA to the designated
ASA. Once the CEA arrives at the ASA, it is stored in a designated secure area separate from the area
containing US munitions. Regardless of its condition, CEA cannot be intermingled with US munition stocks.
CEA that has been certified or cleared by EOD, QASAS, or military inspectors must be receipted, inspected.
6-13
FM 9-6 Chapter 6
and accounted for in the same way as US munitions. Once the CEA is identified as accurately as possible, it is
entered into the SAAS-MOD system for accountability and control. This procedure must be done as soon as
possible after receipt. Reporting and disposition instructions for CEA are the same as for friendly munitions.
Close control of CEA is required.
Positively identified and serviceable CEA may be compatible for use in US or allied forces weapons systems.
These munitions can greatly ease the burden on the ammunition supply system. Also, CEA can be used as a
substitute for bulk explosives during demolition operations. See FMs 9-13 and 9-15 for more information.
6-14
FM 9-6 Appendix
APPENDIX
STANDARD ARMY AMMUNITION SYSTEM-
MODERNIZATION (SAAS-MOD)
SAAS-MOD is an automated ammu-nition information system that integrates all three levels of operations into
a single software baseline. The three levels are:
q Theater/corps materiel management center.
q Ammunition supply point.
q Division ammunition officer.
For a comparison between SAAS and SAAS-MOD, see Figure A-1.
The primary purpose of SAAS-MOD is to provide information regarding con-ventional ammunition assets to
tactical commanders during wartime conditions. The system is used by all ammunition support activities in the
Active and Reserve Components. SAAS-MOD manages all conventional ammunition, GMLR and their related
components, as well as packaging materials. This automated system can pass and receive almost real-time
information on all conventional munitions resources at the three levels of operations.
SAAS (OLD)
SAAS1
^y
1L\
^ SAAS 3
SAAS-BN
!!>■
DAO
SAAS 4
ATP ATP
SAAS-MOD
TMMC
4 i
i
CMMC
lJ
DAO
ATP ATP
\
(D
ASP
A-1
FM 9-6 Appendix
Figure A-1. SAAS versus SAAS-MOD
NICP
(CCSS)
1
DAAS
esses
TAMMC
SPBS-R
esses
TAAIVIVIC
WARS
u
LOGSA
SAAS
TAMMC
TAMIS
SAASTSA
SAAS
TAAMe/eivivie
DAMMS-R
TTVICA
SPBS-R
1
u
SAAS DAO
ULLS-S4
1
SAAS ATP
SAASCSA
SAAS ASP
i
1
DAMMS-R
MCT
J
Figure A-2. SAAS-MOD interface
SAAS-MOD is a multicommand Stand-ard Army Management Information System (STAMIS) that integrates
all retail munitions supply functions and processes. It does this using automated identification technology
(AIT) such as RF tags and on desktop type computers, in a windows environment. It provides ITV and stock
record accounting at the retail level.
Each SAAS-MOD operating level can function independently of the next higher level, if necessary. When
deployed independently (such as with a modular ammunition platoon in an immature theater), SAAS-MOD
can perform the functions of any level; for example, of a TAMMC. SAAS-MOD can also perform dual roles
(CMMC/ TAMMC) during theater development (see Figure A-2). Functions include management of basic
load, war reserve, and operational stocks. SAAS-MOD also gives users the ability to test wartime scenarios on
existing data bases without disrupting real-time accountability.
SAAS-MOD can interface with the following systems:
q SAAS to SAAS.
q Commodity command standard system (CCSS).
A-2
FM 9-6 Appendix
q Logistics support activity (LSA).
q Worldwide Ammunition Reporting System (WARS).
q Standard Property Book System-Redesign (SPBS-R).
q DA Movement Management System-Redesign (DAMMS-R).
q Unit Level Logistics System, Level 4 (ULLS S-4).
q Combat Service Support Control System (CSSCS).
A-3
FM 9-6 Glossary
GLOSSARY
ABL - ammunition basic load
ACofS - Assistant Cliief of Staff
AINS - Ammunition Information Notices
airhead - a designated location in an area of operations used as a base for supply and evacuation by air
AIS - Automated Information System(s)
AIT - automated identification technology
AMCCOM - armament munitions and chemical compound
ammo - ammunition
ammunition basic load - that quantity of conventional ammunition authorized and required to be on
hand in a unit to meet combat needs until resupply can be accomplished; specified by the TA and
expressed in rounds for ammunition items fired by weapons and in other units of measure for bulk
allotment
ammunition supply point - an area designated to receive, store, and issue Class V materiel; normally
located at or near the division area and operated by the corps DS ammunition company
ammunition support activity - generally, one of the storage areas (CSA/TSA/ASP) whose primary
mission is to receive, store, issue, and maintain the theater's conventional ammunition stocks
ammunition transfer point - a designated temporary site where munitions are transferred from corps
transportation to issuing unit vehicles; forward ATP is normally located in the brigade area, operated by
either the supply company, FSB in a heavy division, the forward supply company of the S&T battalion in
a light division, or the S&T company of the support battalion of a separate brigade; ammunition
company ATP is normally located in the division area, operated by the ordnance company, ammunition
(DS)
AO - area of operations
APS - Army prepositioned stocks
AR - Army regulation
ARFOR - Army force
ASA - ammunition support activity
ASCC - Army service component commander
Gloosary-1
FM 9-6 Glossary
ASG - area support group
ASP - ammunition supply point
AST - ammunition support team
AT - antitank
ATP - ammunition transfer point
BB - break-bulk
BB/CON - break-bulk/container
BCT - brigade combat train
bde - brigade
bn - battalion
BSA - brigade support area
cbt - combat
cess - commodity command standard system
CEA - captured enemy ammunition
CINC - commander in chief
CL - combat load
CMCC - corps movement control center
CMMC - corps materiel management center
CO - company
COMMZ - communications zone
controlled supply rate - the rate of ammunition consumption that can be supported, considering
availability, facilities, and transportation; expressed in rounds per unit, individual, weapon, or vehicle per
day. The TA announces the CSR for each item of ammunition; in turn, the commander of each
subordinate unit determines the CSR for the unit. A unit may not draw ammunition in excess of its CSR
without authority from its next higher HQ. (See FM 101-10-1/2.)
CONUS - continental United States
conv - conventional
convoy - a group of vehicles organized for the purpose of control and orderly movement with or without
escort protection
corps storage area - a site established to store and issue the ammunition requirements of the assigned or
Glossary-2
FM 9-6 Glossary
attached corps combat units; operated by one or more GS ammunition companies. At least one CSA is
needed to support a tactical division using the ASP and ATP network
COSCOM - corps support command
CP - command post
CS - combat support
CSA - corps storage area
CSB - corps support battalion
CSG - corps support group
CSR - controlled supply rate
CSS - combat service support
esses - combat service support control system
CTIL - commander's tracked items list
CTOC - corps tactical operations center
DA - Department of the Army
DAAS - Defense Automated Addressing System
DAC - Department of the Army civilian
DAMMS-R - Department of the Army Movement Management System-Redesign
DAO - division ammunition officer
DCSLOG - Deputy Chief of Staff for Logistics
DCSOPS - Deputy Chief of Staff for Operations and Plans
DD form - Department of Defense form
Department of Defense Identification Code - an alphanumeric designation used to identify a specific
item or component part of Class V materiel (for example, D544 is the DODIC for 155mm projectile, HE)
devs - developments
dir - director
DISCOM - division support command
div - division
DLA - Defense Logistics Agency
DMMC - division materiel management center
Glossary-3
FM 9-6 Glossary
DODIC - Department of Defense Identification Code
DOS - days of supply
DPG - Defense Planning Guidance
DS - direct support
DSA - division support area
DTO - division transportation officer
DTOC - division tactical operations center
DU - depleted uranium
EAC - echelons above corps
EOD - explosive ordnance disposal
EODCT - explosive ordnance disposal control team
EODTIC - Explosive Ordnance Disposal Technical Information Center
FM - field manual
FSB - forward support battalion
G2/J2 - Assistant Chief of Staff (IntelHgence)
G3 - Assistant Chief of Staff (Operations and Plans)
G4 - Assistant Chief of Staff (Logistics)
GMLR - guided missile and large rocket
GS - general support
HEMTT - heavy expanded mobility tactical truck
HHC - headquarters and headquarters company
HHD - headquarters and headquarters detachment
HLP - heavy lift platoon
HN - host nation
HNS - host nation support
HQ - headquarters
HQDA - Headquarters Department of the Army
lAW - in accordance with
Glossary-4
FM 9-6 Glossary
ICM - improved conventional munition
lED - improvised explosive device
IOC - Industrial Operations Command
IPB - intelligence preparation of the battlefield
ISO - International Standardization Organization
ITV - in-transit visibility
JTF - joint task force
LAW - light antitank weapon
lift - (of ammunition) the use of MHE to pick up ammunition and put it down, with each pickup and
put-down constituting one lift. When containerized ammunition is received at the CSA or TSA, it is
off-loaded with a rough-terrain container crane. The ammunition is unloaded with a variable-reach
forklift and placed in a storage location. When issued, the ammunition is picked up by a rough-terrain
forklift and placed on a vehicle. Each of these movements constitutes a lift, for a total of three lifts to
receive, rewarehouse, and issue the ammunition
LOC - lines of communication
LOGCAP - Logistics Civilian Augmentation Program
LOGSA - logistics support activity
LOTS - logistics over-the-shore
LPT - logistics preparation of the theater
LSA - logistics support activity
LSE - logistics support element
MACOM - major Army command
Maneuver-Oriented Ammunition Distribution System - an ammunition supply system designed to
provide 100 percent of combat units' (infantry, armor, field artillery, combat aviation, combat engineers,
air defense artillery) ammunition requirements through the ATP network. Corps transportation (ground
and air) is allocated and operates in a DS role to support ammunition shipments from the CSA to ASPs
and ATPs, and from ASPs to ATPs
MATO - materiel office(r)
MCA - movement conrol agency
MCC - movement control center
MCL - mission-configured load
METT-T - mission, enemy, troops, terrain and weather, and time available
Glossary-5
FM 9-6 Glossary
MHE - materials-handling equipment
MICOM - Missile Command
mission-configured load - ammunition configured/reconfigured into complete round mix/weapon
system mix to meet a specific theater of operations requirement
MLP - medium-lift platoon
MMC - materiel management center
MMR - Military Munitions Rule
MO ADS - Maneuver-Oriented Ammunition Distribution System
MOADS-PLS - MO ADS -palletized load system
MOD - modernization
MOS - military occupational specialty
MP - military police
MSB - main support battalion
MSE - mobile subscriber equipment
MTS - movement tracking system
NATO - North Atlantic Treaty Organization
NATO standardization agreement - the record of an agreement among several member nations to
adopt like or similar military equipment, ammunition, supplies, and stores and operational, logistic, and
administrative procedures. National acceptance of a NATO allied publication issued by the Military
Agency for Standardization may be recorded as a standardization agreement
NBC - nuclear, biological, chemical
NCO - noncommissioned officer
NEPA - National Environmental Policy Act
NICP - National Inventory Control Point
NMP - - National Maintenance Point
OCONUS - outside continental United States
ODCSLOG - Office of the Deputy Chief of Staff for Logistics
ODCSOPS - Office of the Deputy Chief of Staff for MiHtary Operations and Plans
OPCON - operational control
Glossary-6
FM 9-6 Glossary
OPLAN - operation plan
OPLOG - operational logistics
OPORD - operation order
pam - pamphlet
PL - public law
PLS - palletized load system
POD - port of debarkation
POL - petroleum, oils, and lubricants
PP - packaging and preservation
push/pull system - push system: the automatic resupply of ammunition consumed by the user;
consumption rate is calculated by the type and quantity of ammunition issued to the user from stocks on
hand at the issuing facility. Issues are reported through daily transaction reports to the CMMC by the
issuing activity (such as an ASP, an ATP, or DAG). That quantity along with any new or additional
requirements is pushed into the supply pipeline at the CSA or TSA to replenish or add to mission stocks
forward. Pull-system: uses DAG requests for Class V by type and quantity to satisfy mission
requirements
QA - quality assurance
QASAS - quality assurance specialist (ammunition surveillance)
QC - quality control
RAOC - rear area operations center
RC - Reserve Component
RCRA - Resource Conservation and Recovery Act
required supply rate - the quantity of ammunition expressed as rounds per weapon per day for
ammunition items fired by weapons; as other units of measure per day, for bulk allotment and other items
required to sustain operations of any designated force without restriction for a specified period
RF - radio frequency
ROD - report of discrepancy
RSR - required supply rate
53 - Operations and Training Officer
54 - Supply Officer
SAAS - Standard Army Ammunition System
Glossary-7
FM 9-6 Glossary
SAAS-MOD - Standard Army Ammunition System-Modernization
SASO - stability and support operations
SB - supply bulletin
SF - standard form
SFC - sergeant first class
short ton - the equivalent of 2000 pounds (0.907 metric ton) of weight
SITREP - situation report
sling out - ammunition loaded into cargo nets and rigged beneath a helicopter. Sling-out operations are
conducted primarily for emergency resupply of units not accessible by ground transport or when time or
security is a critical factor
SOP - standing operating procedure
SOUMS - safety of use messages
SPBS-R - Standard Property Book System-Redesign
spt - support
SRC - standard requirement code
ST/STON - short ton
STAMIS - Standard Army Information System
STANAG - standardization agreement
strategic comfigured load - ammunition loaded into an ISO container or ISO-compatible flatrack at a
CONUS depot or facility in a complete round mix for artillery and a weapon system mix for other
systems (tanks, Bradleys, Apaches, etc)
SUPCOM - support command
SVC - service
TA - theater army
TAACOM - theater army area command center
TACOM - theater army command
TAMCC - theater army movement control center
TAMIS - Training Ammunition Management Information System
TAMMC - theater army materiel management center
TAV - total asset visibility
Glossary-8
FM 9-6 Glossary
TB - technical bulletin
TC - training circular
tech - technical
theater storage area - within the COMMZ, operated by one or more ordnance companies ammunition
(GS); receives, stores, issues, and maintains the theater's conventional ammunition reserves; should be
linked with air, road, rail, and seaborne networks and facilities when possible
TM - technical manual
TMCA - theater movement control agency
TMMC - theater materiel management center
TOE - table(s) of organization and equipment
TPFD - time-phased force deployment
TRADOC - US Army Training and Doctrine Command
TRANSCOM - transportation command
TSA - theater storage area
ULLS-4 - Unit-Level Logistics System-S4
US - United States (of America)
USACAA - US Army Concepts Analysis Agency
USACASCOM - US Army Combined Arms Support Command
USACASCOM&FL - US Army Combined Arms Support Command and Fort Lee
USAMC - US Army Materiel Command
USSS - United States Secret Service
UXO - unexploded ordnance
VIP - very important person
WARS - Worldwide Ammunition Reporting System
WD - weapons density
WHNS - wartime host nation support
Glossary-9
FM 9-6 References
REFERENCES
SOURCES USED
The following sources are quoted or paraphrased in this publication.
AIS Manual 25-L6F-AJA-ZZZ-EM. Standard Army Ammunition System Modernization (SAAS-MOD). 1
November 1995.*
AR 75-15. Responsibilities and Procedures for Explosive Ordnance Disposal. 1 November - 1978.
AR 190-11. Physical Security of Arms, Ammunition, and Explosives. 30 September 1993.
AR 200-1. Environmental Protection and Enhancement. 23 April 1990.
AR 200-2. Environmental Effects of Army Actions. 23 December 1988.
AR 381-26. (S) Army Foreign Materiel Exploitation Program (U). 27 May 1991.
AR 385-10. The Army Safety Program. 23 May 1988.
AR 385-40. Accident Reporting and Records. 1 November 1994.
AR 385-64. Ammunition and Explosives Safety Standards. 22 May 1987.
AR 710-1. Centralized Inventory Management of the Army Supply System. 1 February 1988.
AR 710-2. Inventory Management Supply Policy Below the Wholesale Level. 31 January 1992.
DA Pamphlet 385-1. Small Unit Safety Officer/NCO Guide. 22 September 1993.
FM 5-250 . Explosives and Demolitions. 15 June 1992.
FM 9-13 . Ammunition Handbook. 4 November 1986.
FM 9-15 . Explosive Ordnance Disposal Service and Unit Operations. 8 May 1996.
FM 19-30 . Physical Security. 1 March 1979.
FM 20-400. Military Environmental Protection. October 1996.
FM 54-30 . Corps Support Groups. 17 June 1993.
FM 55-2. Division Transportation Operations. 31 January 1985.
FM 63-3 . Corps Support Command. 30 September 1993.
FM 63-4 . Combat Service Support Operations-Theater Army Area Command. 24 September - 1984.
References- 1
FM 9-6 References
FM 63-11 . Logistic Support Element. October 1996.
FM 100-5 . Operations. 14 June 1993.
FM 100-7 . Decisive Force: The Army in Theater Operations. 31 May 1995.
FM 100-10 . Combat Service Support. 30 October 1995.
FM 100-16 . Army Operational Support. 31 May 1995.
FM 100-27 . US Army/US Air Force Doctrine for Joint Airborne and Tactical Airlift Operations. 31
January 1985.
FM 101-10-1/2. Staff Officers Field Manual-Organizational, Technical, and Logistical Data, Planning
Factors (Volume 2). 7 October 1987.
Military Munitions Rule. Federal Register, 40 CFR, Part 260. 12 February 1992.
SB 742-1. Ammunition Surveillance Procedures. 12 November 1990.
STANAG 2034 (Edition 4). Land Forces Procedures for Allied Supply Transactions. 20 December 1982.
STANAG 2135 (Edition 3). Procedures for Emergency Logistic Assistance. 12 February 1982.
STANAG 2827 (Edition 2). Materials Handling in the Field. 12 February 1980.
STANAG 2829 (Edition 2). Materials Handling Equipment. 20 March 1978.
STANAG 2834 (Edition 2). The Operation of the Explosive Ordnance Disposal Technicallnformation
Centre (EODTIC). 26 March 1990.
STANAG 2928 (Edition 3). Land Forces Ammunition Interchangeability Catalog in Wartime. 9 June
1995.
STANAG 2961 (Edition 1). Classes of Supply of NATO Land Forces. 11 December 1984.
TB 9-1300-278. Guidelines for Safe Response to Handling, Storage, and Transportation Accidents
Involving Army Tank Munitions or Armor Which Contain Depleted Uranium. 21 July 1996.
TB 9-1300-385. Munitions Restricted or Suspended. 1 September 1996.
TC 5-400 . Unit Leaders' Handbook for Environmental Stewardship. 29 September 1994.
TM 9-1300-206. Ammunition and Explosives Standards. 30 August 1973.
TM 9-1300-250. Ammunition Maintenance. 25 September 1969.
TM 43-0002-33. Destruction of Conventional Ammunition and Improved Conventional Munitions (ICM)
to Prevent Enemy Use. 15 November 1993.
TOE 09408L000. HQs, Modular Ammo Ordnance Company.
TOE 09433L000. Ordnance Company, Ammo PLS/MOADS, CSA.
References-2
FM 9-6 References
TOE 09483L000. Ordnance Company, Ammo (MO ADS) DS.
TOE 09484L000. Ordnance Company, Ammo DS (PLS/MOADS).
TOE 09488L000. Ordnance Company, Ammo, Conv, GS.
TOE 09503 LAOO. Modular Ammo Ordnance, Medium Lift Platoon.
TOE 09503LB00. Modular Ammo Ordnance, Heavy Lift Platoon.
TOE 09662L000. HHD, Ordnance Group, Ammo.
TOE 09666L000. HHD, Ordnance Battalion (Ammo) DS/GS.
Unit Supply Update 2-14. 28 February 1994..
DOCUMENTS NEEDED
The following documents must be available to the intended users of this publication.
DA Form 285. U.S. Army Accident Report. January 1992.
DA Form 984. Munition Surveillance Report Descriptive Data of Ammunition Represented by Sample.
June 1980
DA Form 2028. Recommended Changes to Publications and Blank Forms. 1 February 1974.
DA Form 2415. Ammunition Condition Report. 1 December 1977.
DA Form 3020-R. Magazine Data Card. August 1989.
DA Form 3022-R. Army Depot Surveillance Record. May 1990.
DA Form 3023. Gage Record. 1 July 1965.
DA Form 3782. Suspended Notice. September 1971.
DA Form 4508. Ammunition Transfer Record. May 1976.
DD Form 250. Materiel Inspection and Receiving Report. November 1992.
DD Form 1575. Suspended Tag Materiel. October 1966.
DD Form 1575-1. Suspended Label Materiel. 1 October 1966.
DD Form 1650. Ammunition Data Card. September 1986.
SF Form 361. Transportation Discrepancy Report. March 1984.
SF Form 364. Report of Discrepancy (ROD). February 1980.
READINGS RECOMMENDED
The following readings contain relevant supplemental information.
References-3
FM 9-6 References
AR 11-11. (C) War Reserves (U). 1 June 1985.
AR 40-13. Medical Support Nuclear/Chemical Accidents and Incidents. 1 February 1985.
AR 40-14. Occupational Ionizing Radiation Personnel Dosimetry. 30 June 1995.
AR 50-5. Nuclear and Chemical Weapons and Material Nuclear Surety. 3 October 1986.
AR 50-5-1. (C) Nuclear Weapon Security. 1991.
AR 50-6. Nuclear and Chemical Weapons and Material, Chemical Surety. 1 February 1995.
AR 55-203. Movement of Nuclear Weapons, Nuclear Components, and Related Classified Nonnuclear
Materiel. 31 October 1974.
AR 55-228. Transportation by Water of Explosives and Hazardous Cargo. 30 April 1969.
AR 55-355. Defense Traffic Management Regulation. 31 July 1986.
AR 75-1. Malfunctions Involving Ammunition and Explosives. 20 August 1993.
AR 190-13. The Army Physical Security Program. 30 September 1993.
AR 190-40. Serious Incident Report. 30 November 1993.
AR 190-51. Security of Unclassified Army Property (Sensitive and Nonsensitive). 30 September 1993.
AR 190-59. Chemical Agent Security Program. 27 June 1994.
AR 380-67. The Department of the Army Personnel Security Program. 9 September 1988.
AR 385-11. Ionizing Radiation Protection (Licensing, Control, Transportation, Disposal, and Radiation
Safety). 1 May 1980.
AR 725-50. Requisition, Receipt, and Issue System. 15 November 1995.
AR 735-5. Policies and Procedures for Property Accountability. 28 February 1994.
DA Pamphlet 710-2-1. Using Unit Supply System (Manual Procedures). 1 January 1982.
FM 3-100 . Chemical Operations Principles and Fundamentals. 8 May 1996.
FM 5-100 . Engineer Operations. 27 February 1996.
FM 6-20 . Fire Support in the AirLand Battle. 17 May 1988.
FM 7-30 . The Infantry Brigade. 3 October 1995.
FM 9-38 . Conventional Ammunition Unit Operations. 2 July 1993.
FM 9-59. Maintenance Operations for Air Defense and Land Combat Weapons Systems. 8 March 1994.
FM 10-27 . General Supply in Theaters of Operations. 20 April 1993.
References-4
FM 9-6 References
FM 10-27-2 . Tactics, Techniques, and Procedures for Quartermaster Direct Support Supply and Field
Service Operations. 18 June 1991.
FM 10-67 . Petroleum Supply in Theaters of Operations. 16 February 1983.
FM 19-1 . Military Police Support for the AirLand Battle. 23 May 1988.
FM 21-16 . Unexploded Ordnance (UXO) Procedures. 30 August 1994.
FM 24-1. Signal Support in the AirLand Battle. 15 October 1990.
FM 41-10 . Civil Affairs Operations. 11 January 1993.
FM 43-5. Unit Maintenance Operations. 28 September 1988.
FM 43-11. Direct Support Maintenance Operations (Nondivisional). 5 September 1991.
FM 43-12. Division Maintenance Operations. 10 November 1989.
FM 43-20. General Support Maintenance Operations. 10 November 1989.
FM 44-100 . US Army Air Defense Operations. 15 June 1995.
FM 54-23 . Materiel Management Center, Corps Support Command. 28 December 1984.
FM 54-40 . Area Support Group. 3 October 1995.
FM 55-450-2 . Army Helicopter Internal Load Operations. 5 June 1992.
FM 55-450-3. Multiservice Helicopter External Air Transport: Basic Operations and Equipment. 11
February 1991.
FM 55-450-4. Multiservice Helicopter External Air Transport: Single-Point Rigging Procedures. 11
February 1991.
FM 55-450-5 . Multiservice Helicopter External Air Transport: Dual-Point Load Rigging Procedures. 11
February 1991.
FM 63-1 . Support Battalions and Squadrons, Separate Brigades and Armored Calvary Regiment. 30
September 1993.
FM 63-2 . Division Support Command, Armored, Infantry, and Mechanized Infantry Divisions. 20 May
1991.
FM 63-20 . Forward Support Battalion. 26 February 1990.
FM 63-21 . Main Support Battalion. 7 August 1990.
FM 71-100 . Division Operations. 28 August 1996.
FM 90-2. Battlefield Deception. 3 October 1988.
References-5
FM 9-6 References
FM 100-15 . Corps Operations. 29 October 1996.
FM 100-17-1 . Army Pre-Positioned Afloat Operations. 27 July 1996.
FM 100-20 . Military Operations in Low Intensity Conflict. 5 December 1990.
FM 101-10-1/1. Staff Officers Field Manual Organizational, Technical and Logistical Data (Volume
One). 7 October 1987.
SB 38-26. (C) Nonnuclear Ammunition Supply Rates (U). 20 April 1979.
TM 3-250. Storage, Shipment, Handling, and Disposal of Chemical Agents and Hazardous Chemicals. 7
March 1969.
TM 5-315. Firefighting and Rescue Procedures in Theaters of Operations. 20 April 1971.
TM 38-L06-10. Logistics Information System Overview Standard Army Ammunition System (SAAS). 1
May 1980.
TM 38-L06-11-1. Functional Users Manual for Standard Army Ammunition System-1 (SAAS-1):
Functional Procedures. 1 October 1980.
TM 38-L06-11-2. Functional Users Manual for Standard Army Ammunition System-1 (SAAS-1):
Appendixes A, B, and C 1 October 1980.
TM 38-L06-11-3. Functional U sers Manual for Standard Army Ammunition System-1 (SAAS-1):
Appendixes D thru J. 1 October 1980.
TM 38-L69-11. Standard Army Ammunition System (SAAS) Level 4 Manual: System Stock Control
Procedures. 30 September 1983.
PROJECTED PUBLICATIONS
The following manuals are scheduled for publication during the fiscal year specified:
FM 9-20. Technical Escort Operations. FY 97 (supercedes TC 9-20, Technical Escort - Operations, 3
October 1988.)
FM 20-400. Military Environmental Protection. FY 98.
* Request copies of the AIS manual through:
CDR USAISSDCL
ATTNASQBILAC
10500 A AVENUE
FORT LEE VA 23801-6065
References-6
FM 9-6 Authentication
FH 9-6
2 MARCH 1993
By Order of the Secretary of the Army;
DENNIS J, REIMER
^^ . G&nerat, United States Army
/I y ^ ^/ Chief of Staff
^JOEL B, HUDSON
Administrative Assistant to the
Secretaiy at tf^e Army
04380
DIsrSlIBiJTION:
Active Arny, Army National Guard, and US Army Reserve: To
be distributed in accordance with the initial distribution
number 110087, requirements for FM 9-6,
PIN: 023665-000