Document text
COMPACT DISC PLAYBACK
1 . Press the (!) STANDBY button to turn to function mode.
2. Press OPEN button to insert a CD into the slot with printed side
facing upward and close the door.
3. Press the FUNCTION button to select CD mode. After loading the
CD, total tracks of the disc will be shown.
4. Press the hi button to begin play.
Note:
LCD display will return to Clock
mode after about 15 sec with no
further operation.
To Interrupt Playback
• Press the hi button.
•To resume playback, press the hi button again.
To Stop Playback
• Press the ■ button.
To Remove the Disc
• Press the OPEN button and take the CD out.
To Review CD Track No.
• Press hi to review CD track no.
Note: This operation will cause instant stop of track playing.
Track Search - Locating a Particular Point In a Track
• Keep the m or button pressed during play and release at the
desired point.
Tracks Skip - Skipping To The Previous or Next Track
• Press the m button once to return to the beginning of the current
track.
• Press the m button repeatedly to skip tracks backward one by one.
• Press the ►w button repeatedly to skip tracks forward one by one.
Repeat Play
This function will allow a single track or all tracks on the disc to be
played repeatedly. REPEAT function can be operated when playing
a disc.
1. To repeat the same track, press
the PRESET/REPEAT button
until “REPEAT” icon lights up
on the display.
2. To repeat the disc, press the
PRESET/REPEAT button until
“REPEAT ALL” icon lights up
on the display.
3. To cancel repeat play, press
the PRESET/REPEAT button
until “REPEAT” icon
disappears from the display.
Note:
LCD display will return to Clock mode after about 15 sec with no
further operation.
Program Play
Program play allows the selected tracks play in desired order.
Program function can only be operated in stop mode.
1 . Turn on the power and press the FUNCTION button to select CD
mode.
- 9 -
- 10 -
WAKE UP TO ALARM (TUNER,CD OR BUZZER)
The TUNER, CD or BUZZER automatically sounds at the designated
time everyday. You can set two different kinds of alarm time, one for
ALARM 1 and the other for ALARM 2.
Setting Alarm 1 (Same As Setting ALARM 2)
1 . Press STANDBY button to return to clock mode.
2. Press ALARM 1 button until “0”
and alarm time start to flash.
Note:
If ALARM 1 button is pressed
again, this operation will go cycle
until wake up mode (TUNER, CD
or BUZZER) is confirmed by
pressing MEMORY/SET button.
3. Press m button to adjust hour.
4. Press »\ button to adjust minute.
5. Press MEMORY/SET button to
confirm Alarm 1 wake up time.
And “ £3 ” appears on the display
which means ALARM 1 has
been set.
OFF —► EHZED
t
\
<23^
~ If] If Hit -
AM N | /
)
_ in n_
ru u
/ l x
viz
) MIN
_ - 62223 -
) +
I /
in i
ru i
/ 1 x
\\ MEMORY/
)) SET
BEHI3
5 ^
i 3 -n n
ICIIU
Alarm On with Tuner, CD and Buzzer
v | / \ I /
When the designated alarm time comes, -[&- -mj-
the selected sound source (TUNER, CD ' 1 ^ ^ '
or BUZZER) will be triggered and the Tl'ri “|
ALARM symbol will start to flash. Q Q.C
Turn Off the Alarm
To turn off the alarm, press STANDBY, ALARM 1 or ALARM 2 button.
The alarm will go off instantly until the same time next day.
Important note:
In case of wake up with TUNER or CD, no other operation such as
CD Stop can be made until turn off the alarm by pressing STANDBY,
ALARM 1 or ALARM 2, and then change the unit to TUNER or CD
mode for further operations.
To Review the Set Alarm Time
• Press ALARM button while the unit is in power off.
To Cancel Alarm Mode
• Press ALARM button until all wake up modes (TUNER, CD or
BUZZER) disappear from the display, then press MEMORY/SET
button to confirm.
Snooze
• Press SNOOZE button allows you to enjoy another 5 minutes’
sleep. Alarm will be on again after 5 minutes of each press of
SNOOZE button until STANDBY, ALARM 1 or ALARM 2 button is
pressed.
-12
- 13 -
2. Press MEMORY/SET button (in stop mode), first “ P 0 I” will appear
for about 2 seconds and then “ 0 0” will flash on the display.
3. Press m or button to select the desired track. Then press
MEMORY/SET button to store the track in memory.
4. To add additional tracks, repeat setp 2 ~ 3.
Notes:
• Check the program order.
• Press MEMORY/SET button repeatedly.
• To stop program play, press STOP button or select other function
by pressing FUNCTION button.
• The same track can be selected more than once in the same
program.
• A maximum of 20 tracks can be programmed.
• With program on, the m or skip function is available only for the
selected tracks.
• REPEAT play can be performed during program play.
CONNECTING HEADPHONES
Connect headphones (Dia. 3.5mm
stereo mini plug) to the PHONE
jack. When the headphones are
connected, speaker sound will be
automatically disconnected.
-11 -
Alarm Clock
AM/FM Radio
With CD Player
INSTRUCTION MANUAL
For best results, please read this manual carefully before using the
unit.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THE UNIT TO RAIN OR
MOISTURE.
TO AVOID ELECTRICAL SHOCK, DO NOT OPEN
THE CABINET.
REFER SERVICING TO QUALIFIED
PERSONNEL ONLY.
CARE AND MAINTENANCE
General Guidelines
• Do not touch the laser lens on the CD player.
• Temperature changes may cause condensation on the laser lens.
If condensation forms on the lens, leave the unit for about an hour
until condensation evaporated.
• Do not leave the unit exposure directly under sunlight or extreme
heat such as inside a car parked in the sun. This can cause damage
or malfunction.
•To prevent dust from reaching internal components, do not leave
compartment door such as back up battery door opened at all time.
• Do not cover unit with cloth.
Handling of Compact Disc
• Although the music tracks in the disc are covered with enclosure,
it is still advisable to treat the disc carefully. Always pick up the disc
by the edge and put them back in the holders immediately after use.
• Always wipe the compact disc from centre to the edge of disc with
a piece of velvet or soft dry cloth.
TROUBLE SHOOTING GUIDE
CD
RADIO
Problems Solutions
Poor FM reception • Make sure FM antenna wire is fully extended.
• Electrical interference in your home can
cause poor reception. Move the unit away
from them (especially those with motors
and transformers).
Poor AM reception • Rotate the unit horizontally.
CLOCK
Problems Solutions
Clock does not show
the correct time.
Alarm does not come
on at the preset time.
• There has been an electrical power
interruption.
To turn on the TUNER, CD or BUZZER alarm,
check the following points:
• Is the current time correctly set on the time
display? Check the AM/PM indication.
• Is the alarm time correctly set? Check the
AM/PM indication.
• Is the desired station tuned in?
SPECIFICATIONS
Problems Solutions
System does not turn
on.
Disc in place but unit
won't play.
• Make sure the STANDBY button is set to
ON.
• Make sure press the FUNCTION button to
CD mode.
• Make sure disc is clean and undamaged.
• Make sure printed side of disc is facing up.
• Make sure PAUSE mode is not activated.
Power consumption: 8W
Power requirements: AC 120V - 60Hz
DC 9V
Specifications are subject to change without notice.
- 14 -
Printed in China
811-308091-010
CAUTION
PRECAUTIONS
The use of optical instruments with this product will increase eye
hazard.
Information (for the customers in USA)
This equipment has been tested and found to comply with the limits
for a Class B digital device. Pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception. Which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet that is on a circuit different
from the one the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
You are cautioned that any changes or modifications not expressly
approved in this manual could void you authority to operate this equipment.
For the customers in the United Kingdom and/European countries
This apparatus complies with the Class B limits
for radio noise emission set out in radio
interference regulations.
This product contains a low power laser device.
On Safety
As the laser beam used in this compact disc player could be harmful
to the eyes, do not attempt to disassemble the casing. Refer servicing
to qualified personnel only.
• Do not put any foreign objects in the disc compartment. If you do so,
the laser beam interlock may be defeated allowing the laser to
remain on when the lid is opened.
• Do not put any foreign objects in the DC 9V(external power input)
jack. Should any solid objects or liquid fall into the unit, disconnect
the power supply and have the unit checked by qualified personnel
before any further operation.
On Operation
Since the CD system offers a wide dynamic range, the peaks of the
high level inputs are recorded with high fidelity, and the noise level is
very low. Do not turn up the volume while listening to a part of the disc
with no audio signals or very low level inputs. If you do so, the
speakers may be damaged when the peak level of the sound is
played. The lens of the laser should be kept clean. Do not touch the
lens or poke at it with your fingers. If you do so, the lens may be
damaged and the unit will not operate correctly.
On Use
Never use the unit where it would be subject to:
- Heat sources such as radiators or airducts.
- Direct sunlight.
- Excessive dust.
- Moisture or rain.
- Mechanical vibration or shock.
- Unleveled surface.
• Do not place any heavy object on top of the unit.
• When the unit is used with an AC power adaptor, do not wrap the
unit in a cloth, blanket, etc. If you do so, the temperature inside
This compact disc player is classified
as a CLASS 1 LASER product.
The CLASS LASER PRODUCT label
is located on the bottom exterior.
For the customers In Canada
CLASS 1 LASER PRODUCT
APPAREIL A LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
PRODUTO LASER CLASSE 1
CAUTION:INVISIBLE LASER
RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED.
AVOID EXPOSURE TO BEAM.
-1 -
- 2 -
CLOCK SETTING IN STANDBY MODE
3. Press BAND button to FM or
f n J BAND
Connect the AC power cord to a wall outlet.
AM.
□ "►
in o n
1 u u.u
In Clock Mode
1. Press MEMORY/SET button for
about 3 seconds. Normally hour
and minute digit will flash.
2. Press m button to adjust hour.
3. Press »\ button to adjust minute.
4. Press MEMORY/SET button to
confirm.
MEMORY/
n J) SET
AM 1 1 /
□ ^
AM | | /
i D-n n
IL *UU
I I
1 1
/
in
i
ru
r
/ I I
MEMORY/
nj) SET
H ^
tin i
'flu 1
LISTENING TO THE RADIO
1 . Press the (!) STANDBY button
to turn on the unit.
0 STANDBY
2. Press the FUNCTION button to
TUNER.
4. Press m or button to tune to
a desired station.
Note:
LCD display will return to CLOCK mode after about 15 seconds
with no further operation.
For Better Radio Reception
AM
Rotate the unit horizontally.
FM
Extend the external FM antenna
wire.
CAUTION:
DO NOT CONNECT TO OUTSIDE ANTENNA.
To Search For a Station Automatically
• Press and hold the m or »\ button still for 1 to 2 seconds, and a
station is searched automatically. Search will automatically stop
when a station is tuned.
Note:
• The search may not stop at a station if the broadcast station signal
is too weak.
To Receive The FM Broadcast in Stereo
1. Press BAND button to FM.
2. When receiving FM broadcast in stereo, the
"ranswj” indicator will light up.
-5
- 6 -
LOCATION OF CONTROLS
and outside the unit may rise considerably, resulting in
malfunctioning of the unit.
• If the unit is brought directly from a cold to a warm location, or is
placed in a very damp room, the moisture may condense on the
lens inside the unit. Should this occur, the unit will not operate. In
this case, remove the disc and leave the unit in a warm place for
several hours until the moisture evaporates.
• For the unit to operate at its best, it should not be subjected to
temperatures below 5°C (41° F) or above 35°C (95° F).
POWER SUPPLY
AC POWER ADAPTOR
Please use a 9V 500mA power
adaptor. Plus pole “ © ” to the
center pin of the 5.5mm socket.
When the unit is not in use, be
sure to disconnect the AC power
adaptor from the mains supply.
To AC outlet
Remarks:
If AC cord is unplugged, please wait 5 seconds before AC cord is
plugged in again.
TURNING ON THE UNIT
Plug the AC adaptor to AC outlet. This display will light up in standby
mode.
Press (1) STANDAY button, and press FUNCTION button to select
the desired function, the corresponding indicator will light up.
ADJUST THE SOUND
Rotate the VOLUME to adjust sound level.
Top View
7
8
9
10
11
Front View
1. (!) STANDBY button
2. SLEEP button
3. MEMORY/SET button
4. HR/TUNING ©button
5. CD OPEN button
6. mh MIN/TUNING ©button
7. DIMMER button
8 . FUNCTION button (RADIO/CD)
9. ■ CD STOP/BAND button
10. hi CD PLAY/PAUSE button
11. SNOOZE button
12. PRESET+ /
REPEAT button
13. PHONE jack
14. PRESET - button
15. COLORS button
16. ALARM 1 button
17. Display window
18. VOLUME control
19. ALARM 2 button
- 3 -
- 4 -
Presetting Station Setting
The unit can store AM -10 stations, FM -10 stations. It can be tuned
into by selecting their preset numbers. It is possible to store station of
any band in order of your choice.
1. Press BAND to select FM or AM band.
2. Press m or »\ button to tune to a desired station.
3. Press MEMORY/SET button
until “MEMORY” indicatorflash.
4. Press PRESET + or PRESET-
button to select channel number.
5. Press MEMORY/SET button until “MEMORY” indicator lights up to
memorize the station.
6. Repeat steps 1 to 5 for the next preset.
Tuning Into a Preset Station
1 . Press BAND button to select FM
or AM band.
2. Press PRESET + or PRESET -
button to select a preset number.
DISPLAY COLOR AND BRIGHTNESS
• Press DIMMER button to change the LCD display brightness.
• Press COLORS button to repeatedly select the multi-color display
changed cyclically as below.
ORANGE —► GREEN —► RED
i _i
SETTING SLEEP FUNCTION
When the sleep timer is used, the power will be automatically turned
off after the specified time passes.
Set in CD or Tuner Mode
1. Press SLEEP button while the
power is on. “SLEEP” and “ 0 0”
light up.
2. Press SLEEP button to select
the length of remaining time until
3LEEP
the unit turns off.
u ^
3 n
DU
It changes the indicator in following way:
00 — 90 — 15 — 60 — 45
i i
0 1 -— 05 -— JO -— J 5 -— 30
- 7 -
To cancel the sleep timer, press SLEEP button until “ 0 0”show in
display.