Document text
BUCK BOX
NETWORK SERVICES
LPJ008A-F
LPJ008A-FM
LPJ008A-T
LPJ008A-TM
LPJ016A-F
LPJ016A-FM
LPJ016A-T
LPJ016A-TM
LPJ024A-F
LPJ024A-FM
Gigabit speed plus extra power for high-wattage
devices.
Managed and unmanaged versions available.
Conform to IEEE 802.af or 802.at specifications.
802.3af and 802.3at PoE Gigabit Injectors
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mailing address: Biack Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Web site: www.blackbox.com • E-mail: [email protected]
Customer
Support
Information
802.3af and 802.3at PoE Gigabit Injectors
Trademarks Used in this Manual
Black Box and the Double Diamond logo are registered trademarks of BB Technologies, Inc.
Windows is a registered trademark of Microsoft Corporation.
Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners.
We're here to help! If you have any questions about your application
or our products, contact Black Box Tech Support at 724-746-5500
or go to blackbox.com and click on "Talk to Black Box."
You'll be live with one of our technical experts in less than 30 seconds.
Page 2
724-746-5500 | blackbox.com
FCC and 1C RFI Statements
Federal Communications Commission and Industry Canada Radio Frequency Interference
Statements
This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict
accordance with the manufacturer's instructions, may cause interference to radio communication. It has been tested and found
to comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC
rules, which are designed to provide reasonable protection against such interference when the equipment is operated in a
commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user
at his own expense will be required to take whatever measures may be necessary to correct the interference.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emission from digital apparatus set out in the Radio
Interference Regulation of Industry Canada.
Le present appareil numerique n'emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques
de la classe A prescrites dans le Reglement sur le brouillage radioelectrique publie par Industrie Canada.
724-746-5500 | blackbox.com
Page 3
802.3af and 802.3at PoE Gigabit Injectors
Instrucdones de Seguridad
(Normas Oficiales Mexicanas Electrical Safety Statement)
1. Todas las instrucdones de seguridad y operacion deberan ser lefdas antes de que el aparato electrico sea operado.
2. Las instrucciones de seguridad y operacion deberan ser guardadas para referenda futura.
3. Todas las advertencias en el aparato electrico y en sus instrucciones de operacion deben ser respetadas.
4. Todas las instrucciones de operacion y uso deben ser seguidas.
5. El aparato electrico no debera ser usado cerca del agua—por ejemplo, cerca de la tina de bano, lavabo, sotano mojado o cerca
de una alberca, etc.
6. El aparato electrico debe ser usado unicamente con carritos o pedestales que sean recomendados por el fabricante.
7. El aparato electrico debe ser montado a la pared o al techo solo como sea recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo electrico mas alia a lo descrito en las instrucciones de operacion.
Todo otro servicio debera ser referido a personal de servicio calificado.
9. El aparato electrico debe ser situado de tal manera que su posicion no interfiera su uso. La colocacion del aparato electrico
sobre una cama, sofa, alfombra o superficie similar puede bloquea la ventilacion, no se debe colocar en libreros o gabinetes
que impidan el flujo de aire por los orificios de ventilacion.
10. El equipo electrico deber ser situado fuera del alcance de fuentes de calor como radiadores, registros de calor, estufas u otros
aparatos (incluyendo amplificadores) que producen calor.
11. El aparato electrico debera ser connectado a una fuente de poder solo del tipo descrito en el instructivo de operacion, o como
se indique en el aparato.
12. Precaucion debe ser tomada de tal manera que la tierra fisica y la polarizacion del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados
sobre o contra ellos, poniendo particular atencion a los contactos y receptaculos donde salen del aparato.
14. El equipo electrico debe ser limpiado unicamente de acuerdo a las recomendaciones del fabricante.
15. En caso de existir, una antena externa debera ser localizada lejos de las lineas de energia.
16. El cable de corriente debera ser desconectado del cuando el equipo no sea usado por un largo periodo de tiempo.
17. Cuidado debe ser tornado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilacion.
18. Servicio por personal calificado debera ser provisto cuando:
A: El cable de poder o el contacto ha sido danado; u
B: Objectos han cafdo o liquido ha sido derramado dentro del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en su desempeno; o
E: El aparato ha sido tirado o su cubierta ha sido danada.
Page 4
724-746-5500 | blackbox.com
Table of Contents
Table of Contents
1. Specifications.6
2. Overview .7
2.1 Introduction.7
2.2 Features.7
2.3 What's Included.7
2.4 Hardware Description.8
2.4.1 Front Panel.8
2.4.2 Back Panel.9
2.5 Safety Procedures: General Precautions.10
3. Hardware Installation.11
3.1 Power Cord Requirements.11
3.2 Connecting Ethernet Cables.12
3.3 Connecting USB and Power Cables.12
3.4 Powering On the Unit.13
3.5 LED Indicators.13
3.5.1 Cold Start.13
3.5.1 Click System Reset on the Graphical User Interface (GUI).14
3.6 Rackmounting Installation.14
4. Black Box GUI and USB Driver Installation.15
4.1 PC-to-PoE Gigabit Injector GUI.15
4.2 PC-to-PoE Gigabit Injector Connection via USB/R5-232.15
4.3 Device Manager: to View Port Properties.16
4.4 USB Block Diagram.18
5. GUI Operation.19
5.1 GUI Main Window.19
5.2 GUI System Information/Operation.20
5.3 GUI Port Description.21
5.4 GUI Parametric Information.22
6. Troubleshooting.23
Appendix A. Optional Ethernet Interface.24
A.1 Network Interface Setup.24
A.2 Advanced Setup Options.26
A.3 Controller Setup.27
A.3.1 System Administration.28
A.3.2 SNMP Settings.31
A.4 DHCP Client—Dynamic and Static Mode Setup.33
A.5 Setup NIC PoE Gigabit Injector with Black Box GUI.34
Appendix B. SNMP MIB Controls.37
Appendix C. Frequently Asked Questions.42
724-746-5500 | blackbox.com
Page 5
802.3af and 802.3at PoE Gigabit Injectors
1. Spedfications
Compliance: All models: cUL/UL®; RoHS
Connectors: Data in: LPJ008A-F, LPJ008A-FM, LPJ008A-T, LPJ008A-TM: (8) RJ-45 (10/100/1000);
LPJ016A-F, LPJ016A-FM, LPJ016A-T, LPJ016A-TM: (16) RJ-45 (10/100/1000);
LPJ024A-F, LPJ024A-FM: (24) RJ-45 (10/100/1000);
Data/PoE out: LPJ008A-F, LPJ008A-FM, LPJ008A-T, LPJ008A-TM: (8) RJ-45 (10/100/1000);
LPJ016A-F, LPJ016A-FM, LPJ016A-T, LPJ016A-TM: (16) RJ-45 (10/100/1000);
LPJ024A-F, LPJ024A-FM: (24) RJ-45 (10/100/1000);
USB diagnostics port: All models: (1) USB Type B;
Power inlet: All models: (1) IEC 320 (3-pin);
LPJ008A-FM, LPJ008A-TM, LPJ016A-FM, LPJ016A-TM, LPJ024A-FM: Also Ethernet/SNMP port: (1) RJ-45
Indicators: LPJ008A-F, LPJ008A-FM, LPJ016A-F, LPJ016A-FM, LPJ024A-F, LPJ024A-FM: Green LED: Power detected "ON";
LPJ008A-T, LPJ008A-TM, LPJ016A-T, LPJ016A-TM: Green LED: Power detected "CONNECT";
LPJ008A-T, LPJ016A-T, LPJ016A-TM: Flashing green LED: 802.3af detected "CONNECT" at 15.4 W;
All models: Yellow LED: Fault detected
Power: AC input voltage range: 90-264 VAC;
AC input voltage rating: 100-240 VAC, 47-63 Hz;
Output: LPJ008A-F, LPJ008A-FM, LPJ016A-F, LPJ016A-FM, LPJ024A-F, LPJ024A-FM: 15.4 W per port;
LPJ008A-T, LPJ008A-TM, LPJ016A-T, LPJ016A-TM: 33.6 W per port;
Size: 1.75"H (1U) x 17,25"W x 9"D (4.4 x 44 x 23 cm)
Weight: LPJ008A-F, LPJ008A-FM, LPJ016A-F, LPJ016A-FM, LPJ024A-F, LPJ024A-FM: 9 lb. (4.1 kg);
LPJ008A-T, LPJ008A-TM, LPJ016A-T, LPJ016A-TM: 8.5 lb. (3.9 kg)
Page 6
724-746-5500 | blackbox.com
Chapter 2: Overview
2. Overview
2.1 Introduction
Use the Power over Ethernet (PoE) Injectors to reliably power multiple PoE devices. Ten models are available:
• 802.3af PoE Gigabit Injector, 8-Port (LPJ008A-F)
• 802.3af PoE Gigabit Injector, 16-Port (LPJ016A-F)
• 802.3af PoE Gigabit Injector, 24-Port (LPJ024A-F)
• 802.3af PoE Gigabit Managed Injector, 8-Port (LPJ008A-FM)
• 802.3af PoE Gigabit Managed Injector, 16-Port (LPJ016A-FM)
• 802.3af PoE Gigabit Managed Injector, 24-Port (LPJ024A-FM)
• 802.3at PoE Gigabit Injector, 8-Port (LPJ008A-T)
• 802.3at PoE Gigabit Injector, 16-Port (LPJ016A-T)
• 802.3at PoE Gigabit Managed Injector, 8-Port (LPJ008A-TM)
• 802.3at PoE Gigabit Managed Injector, 16-Port (LPJ016A-TM)
2.2 Features
• UNH-IOL test lab certified for interoperability with other PoE equipment.
• An economical wiring solution. Carries both data and power over Ethernet cable run to each port.
• Use to power various VoIP phones, security system cameras, wireless network access points, Bluetooth® access points, and other
802.3af/at-compatible equipment.
• Enables you to avoid the cost and hassle of installing AC power at remote cameras or door scanners.
• Supports 10-/100-/1000-Mbps PoE Gigabit Injector data connections on 8, 16, or 24 RJ-45 inputs/outputs.
• Protection includes overvoltage/overcurrent overload and short circuit protection on the power output (per 802.3af/at
specifications). Provides fully compliant detection and disconnect.
• Overtemperature protection. Provides automatic shutdown without causing any damage.
• Diagnostic LEDs indicate detection of power and faults.
• Also has a USB port for diagnostics and manual port control via a Windows® GUI.
• Simple plug-and-play installation. No power management required.
• Just 1U high, easy to install in a rack or cabinet with the included mounting kit.
• RoHS compliant.
2.3 What's Included
Your package should include the following items. If anything is missing or damaged, contact Black Box Technical Support at 724-
746-5500.
• PoE Injector
• CD-ROM containing this user's manual
• (2) mounting brackets
• (4) screws
• (4) rubber feet
724-746-5500 | blackbox.com
Page 7
802.3af and 802.3at PoE Gigabit Injectors
2.4 Hardware Description
2.4.1 Front Panel
Figure 2-1 shows the front panel of the 24-port PoE Gigabit Injector. Figures 2-2 and 2-3 show close-up views of front-panel
components. Table 2-1 describes the front-panel components.
Figure 2-1. Front panel, 24-port units.
1
Data &
Power
Data
1 5
i
5
3
2
Figure 2-2. Close-up of front-panel data/power and data ports.
3
4 5
Figure 2-3. Close-up of front-panel Ethernet and USB Type B connectors.
Page 8
724-746-5500 | blackbox.com
Chapter 2: Overview
Table 2-1. Front panel components.
Number
Component
Description
1
(24) RJ-45 ports, top row
Data and power ports
2
(24) RJ-45 ports, bottom row
Data ports
3
(1) RJ-45 Ethernet connector
Links to network interface card (only LPJ008A-FM, LPJ016A-FM, LPJ024A-FM
LPJ008A-TM, LPJ016A-TM models have this connector)
4
USB Type B connector
Links to USB
5
AC LED
Lights when AC power is connected
2.4.2 Back Panel
Figure 2-4 shows the back panel of the 24-port PoE Gigabit Injector. Figure 2-5 shows a close-up view of the AC power
connector.
6
Figure 2-4. Back panel.
Figure 2-5. IEC-320 3-pin AC power in connector (#6 in Figure 2-4).
724-746-5500 | blackbox.com
Page 9
802.3af and 802.3at PoE Gigabit Injectors
2.5 Safety Procedures: General Precautions
Please read the following precautions carefully before installing and connecting the system to a power source:
NOTE: Only qualified and trained service personnel (in accordance with IEC 60950 and AS/NZS 3260) should install, replace, or
service the equipment. Install the system in accordance with country or national codes, or to the U.S. National Electric
Code if you are in the United States.
1. The building facilities in which the product will be used requires a fuse or circuit breaker no larger than 15 A for 120 VAC
(U.S.A.) or 10 A, 230 VAC (international). The building facilities must protect the PoE Injector from overcurrent or short circuits.
2. Before connecting the PoE Injector to a power source (including power cord requirements), read the PoE Injector Hardware
Installation procedure in Chapter 3. This procedure, as with all procedures and instructions, can be found in the PoE Injector
User Manual. To download a copy of the manual, visit ftp.blackbox.com.
3. To prevent the PoE Injector from overheating, do not operate the product in an area that exceeds the maximum recommended
ambient temperature of 40° C. Allow at least 3 to 4 inches of clearance around all ventilation openings.
4. To support the PoE Injector weight, do not stack the chassis on any other equipment. Shelf mounted equipment requires a sta¬
ble and durable surface. When installed, do not push or pull on the PoE Injector when the equipment is installed.
5. The PoE Injector consists of two rows of "Data" and "Data & Power" ports. The ports use RJ-45 data sockets. Do not connect
telephone cables into these ports. Only RJ-45 data cables may be connect to these sockets.
6. Do not work on the PoE Injector system or connect or disconnect the cables, during periods of lightning activity.
7. The AC or DC plus/socket combination must be accessible at all times, as it serves as the main disconnect device to the
product.
8. Before servicing the product, always disconnect the product from its AC and DC source.
9. Disposal of this product should abide by all appropriate national laws and regulations.
Page 10
724-746-5500 | blackbox.com
Chapter 3: Hardware Installation
3. Hardware Installation
3.1 Power Cord Requirements
Power cords must meet the requirements for the country where you will use the PoE Injector.
U.S. and Canada
• The cord must have a minimum of 10-A rated current competence.
• The cord must be UL® or CSA approved.
• The minimum requirement for the flexible cord is:
- 18 AWG (10-A)
- Three-conductor (line, neutral, ground)
- Type SV (stranded vacuum rubber jacketed) or SJ (stranded junior rubber jacketed) or SVT (stranded vacuum rubber
jacketed thermoplastic) or SJT (stranded junior thermoplastic)
• The plus must be earth-grounded with a NEMA 5-15 (15A, 125V) or NEMA 6-15P (15A, 250V) configuration.
Europe
Switzerland
• The supply plug must comply with SEV/ASE 1011.
Denmark
• The supply plug must comply with section 108-2-D1, standard DK2-1a or DK2-5a.
United Kingdom
• The PoE Gigabit Injector is covered by General Approval (section 16.16.060, NS/G/12345/J100003, for indirect connection to a
public telecommunication system.
France and Peru
• IT equipment cannot power this device. In the case of an IT-powered device, the unit needs to be powered by 230V through an
isolation transformer with a ratio of 1:1 and the secondary connection (neutral) is properly grounded.
• The PoE Gigabit Injector must have access to a nearby power outlet. By disconnecting the power cord from the outlet, you will
eliminate power from the device.
• The flexible cord that connects to the PoE Gigabit Injector must have a configuration to connect with an EN60320/IEC320 inlet
connector.
• According to the EN60950/IEC 950 specifications, this device functions under SELV (Safety Extra Low Voltage) conditions. The
conditions are true if the equipment and the connected device functions under SELV conditions.
724-746-5500 | blackbox.com
Page 11
802.3af and 802.3at PoE Gigabit Injectors
3.2 Connecting Ethernet Cables
Connect the Ethernet cables (not included) to the PoE Gigabit Injector's data/power and Ethernet ports. See Figures 3-1 and 3-2.
Figure 3-1. PoE Gigabit Injector with Ethernet cables connected to data and power ports.
Figure 3-2. Close-up view of PoE Gigabit Injector with cable connected to Ethernet port.
3.3 Connecting USB and Power Cables
USB cable
Connect a USB cable (not included) to the USB Type B connector located on the front side of the PoE Gigabit Injector and a USB
port on your PC/laptop. See Figures 3-3 and 3-4.
the USB port on the to the USB port
PoE Gigabit Injector) on a PC/laptop)
Figure 3-3. USB cable.
Page 12
724-746-5500 | blackbox.com
Chapter 3: Hardware Installation
Figure 3-4. USB cable connected to PoE Gigabit Injector.
AC power cord
Connect the AC power cable to the AC power connector on the rear of the PoE Gigabit Injector and the power
outlet. See Figure 3-5.
I EC-320 power
connnector
AC power
plug
Figure 3-5. AC power cord.
3.4 Powering On the Unit
The PoE Gigabit Injector receives power via the power cord. To apply or remove power to/from the PoE Gigabit Injector, connect
or disconnect the AC power cable to/from the AC power connector on the rear of the unit.
With AC power applied, the unit starts up and the internal fans are active. The device runs through a quick power-on test, which
takes less than 10 seconds. During this period, all ports are initially disabled and the port indicators light up. The sequence of the
port LEDs are shown in Section 3.5. Ports are now operating under normal conditions.
3.5 LED Indicators
3.5.1 Cold Start
1. AC LED turns green4remains on
2. Ethernet LED turns green4red4green4turns off4red4turns off (unless connected)
3. 24 ports (with ports connected) 4LED turns orange4green4orange4green4turns off4LED turns green individually4Ports 1,
9, 174Ports 2, 10, 184Ports 3, 11, 194Ports 4, 12, 204Ports 5, 13, 214Ports 6, 14, 224 Ports 7, 15, 234Ports 8, 16, 244all
24 ports are connected4LED remains green
4. 24 ports (without ports connected)4LED turns orange4green4orange4green4turns off4LED blinks orange individually
Ports 1, 9, 174Ports 2, 10, 184Ports 3, 11, 194Ports4, 12, 204Ports 5, 13, 214Ports 6, 14, 224Ports 7, 15, 234Ports 8, 16,
244blinks orange across all 24 ports
724-746-5500 | blackbox.com
Page 13
802.3af and 802.3at PoE Gigabit Injectors
3.5.2 Click System Reset on the Graphical User Interface (GUI)
1. AC LED remains green
2. Ethernet LED remains off until the unit is connected
3. 24 ports (with ports connected): same sequence as Cold Start
4. 24 ports (without ports connected): same sequence as Cold Start
Table 3-1 LED Indicators.
Indicator
Conditions
LED Off
Green
Orange
Blinking Orange
Port LED
Indicates port is
disabled
Indicates port is
connected
Indicates port has
an error
Indicates port is
disconnected but enabled
Ethernet LED
Indicates Ethernet is
disconnected from
network
N/A
Indicates NIC is
connected to
network
N/A
AC LED
Indicates PoE Gigabit
Injector is not powered
Indicates PoE Gigabit
Injector is powered
N/A
N/A
3.6 Rackmounting Installation
Position the PoE Gigabit Injector on the rack. Line up the mounting bracket with the corresponding screw holes on the PoE
Gigabit Injector. (See Figure 3-6.) Keep the screw area visible to insert screws, and then tighten the screws. (See Figure 3-7.)
Screws and brackets are included in the package.
o
III III III III III III
■
S'
o
Figure 3-6. 24-port PoE Gigabit Injector with rackmount brackets attached.
Screws
Bracket
PoE Gigabit
Injector
Figure 3-7. Close-up view of rackmounting bracket and screws (side/rear).
Page 14
724-746-5500 | blackbox.com
Chapter 4: Black Box GUI and USB Driver Installation
4. Black Box GUI and USB Driver Installation
Locate and download the GUI Installation file from the included CD-ROM.
4.1 PC-to-PoE Gigabit Injector GUI
Follow the Installation Wizard to install the Black Box GUI for your model, and the USB-to-Serial COM Port driver. You will need
the USB-to-Serial Com Port driver to communicate with the PoE Gigabit Injector via a Communication Port on the PC. See Figures
4-1 and 4-2.
Figure 4-1. Example of the GUI setup window.
NOTE: Call Black Box Technical Support (724-746-5500) to make sure you are installing the latest version of the Black Box GUI.
The example shown uses POE SNMPv3 GUI.
4.2 PC-to-PoE Gigabit Injector Connection via USB/RS-232
Using a USB/RS-232 cable, connect the USB Type B port on the PoE Injector to the USB Type A port on the computer. See Figure
4-2.
PoE Gigabit Injector
PC
Figure 4-2. PC-to-PoE Gigabit Injector connection diagram.
724-746-5500 | blackbox.com
Page 15
802.3af and 802.3at PoE Gigabit Injectors
4.3 Device Manager: to View Port Properties
When you are ready to begin, connect the proper end of the USB-to-Serial cable to your PoE Gigabit Injector and the other to an
available USB port on your PC. If you installed the USB driver described above, your PC will locate the new hardware.
To view which Serial COM Port your PoE Gigabit Injector is installed on, follow these instructions:
1. Click Start—>Control Panel—>System—>System Properties. See Figure 4-3.
< start
System
Click
Device Manager
Figure 4-3. System Properties screen,
and the following window will open:
Figure 4-4. Device Manager screen, Focate and expand ports (COM and FPT).
Double-click the Prolific USB-to-Serial Comm Port icon. In this example, the USB-to-Serial Comm port is installed on COM4. The
COM port will vary, depending on the user.
Page 16
724-746-5500 | blackbox.com
Chapter 4: Black Box GUI and USB Driver Installation
Prolific USB-to-Serial Comm Port (COM4) Properties
General
Pori Sellings
Driver Details
Prolific USBTo-Serial Comm Pori (COM4)
Device type:
Ports (COM & LPT)
Manufacturer: Prolific
Location:
Location 0 (USB-Serial Controller)
Figure 4-5. Prolific USB-to-Serial Comm Port screen.
Click Pori Settings Make sure the Port Setting is as shown. Click
Com Port Number or stay with the default.
Advanced...
Click on the pull-down menu and select the
Prolific USB-to-Serial Comm Port (COM4) Properties
General Pori Sellings Driver Details
0 ®
Bils per second:
Data bits:
Parity:
Stop bits:
Flow control:
19200
8
None
1
Xon/Xoff
Advanced...
Restore Defaults
Figure 4-6. Prolific USB-to Serial Comm Port Properties/Advanced Settings screen.
Click
OK
to save all changes.
NOTE: Write down the COM Port number because the GUI will need to know the exact port on which to search for devices.
724-746-5500 | blackbox.com
Page 17
802.3af and 802.3at PoE Gigabit Injectors
4.4 USB Block Diagram
Figure 4-7. USB block diagram.
Page 18
724-746-5500 | blackbox.com
Chapter 5: GUI Operation
5. GUI Operation
The firmware is supplied with a Graphical User Interface (GUI), which is used to configure and manage the PoE Gigabit Injector
system. If you have successfully installed the Black Box GUI and USB driver as described in Chapter 4, go to the GUI on your desk¬
top or from your Start Menu.
5.1 GUI Main Window
Step 1: Choose the connection type. See Figure 5-1.
Black Box MIDSPAN POE GUI
System Information / Operation
EM®
<♦> BLACK BOX
blackbox.com I +1 (724) 746 SSOO
Reset/Update
System/Port Param.
System Information
Save Parameters
to Flash
Firmware Version
Hardware Version
Port Number |
System
1 Firmware
Restore Factory
Reset
Download
Defaults
System ID
(Description)
Connection Information
Connection Type SNMP/LAN & WAN v
Setting
Port Description
1
Parametric Information
ZL
Port Commands
□ Enable/Disable All Ports Q Detect Legacy Signature
Send Port Control
Portl
0
Port 2
0
Port 3
0
Port 4
0
Port 5
0
Port 6
0
Port 7
0
Port 8
0
Port 9
0
Port 10
0
Port 11
0
Port 12
0
Port
1
Description
Edit
i Edi * 1
Edit
Edit
| Edit [
rE dd J
1 Edit
Edit
II Edit
Edit |
Edit |
Edit |
Enable
Port 13
0
Port 14
0
Port 15
0
Port 16
0
Port 17
0
Port 18
0
Port 19
0
Port 20
0
Port 21
0
Port 22
0
Port 23
0
Port 24
0
1
Description
Edit |
| Edit
1 Edit ;
Edit
1 Edit |
Edit ~|
1 Edit
| Edit
II Edit |
1 Edit |
Edit |
Edit |j
Enable
NOTE: To send changes made in this section to the PoE
system, click on 'Send Port Control'.
LED Key (Port status)
Detecting Disable/Error Port Connected
0 W
Figure 5-1. GUI main window.
Step 2: Select the COM port number, click "Search PoE" and highlight the PoE Gigabit Injector.
Connection Information
Connection Information
Figure 5-2. GUI connection information.
724-746-5500 | blackbox.com
Page 19
802.3af and 802.3at PoE Gigabit Injectors
5.2 GUI System Information/Operation
The System Information/Operation panel on the GUI supports the main system level parameters for the unit. It also displays
information about the PoE ID, firmware revision, and system status.
System Information / Operation
<♦> BLACK BOX 5
blackbox.com I +1 (724) 746-5500
Save Parameters
to Flash
Resel/Update
System
Firmware
Restore Factory
Reset
Download
Defaults
System Information
Firmware Version
Hardware Version
Port Number
System ID
(Description)
Figure 5-3. System setup, control, information, and port commands.
The system level parameters that can be configured are:
• System Reset: This is a function that allows the GUI to reset the software on the unit. (If System Reset is activated and the GUI
does not respond, "Reset GUI.")
• Firmware Download: This feature is used to download new application/firmware codes onto the unit. Contact Black Box Tech
Support at 724-746-5500 or [email protected] for the latest firmware for your PoE Gigabit Injector - POE Firmware.
NOTE: Wait a few seconds for the GUI to respond to the commands selected. DO NOT click or check any commands
simultaneously. If a command is selected more than once within two seconds, the GUI may not respond properly.
The "Save Parameters to Flash" button will save system and port parameters to flash memory, so that they can be used to retain
the firmware across reboots of the unit.
The "Restore Factory Defaults" button will reset the defaults in the firmware and clear any stored data in the flash memory, so
the device will reset automatically. After the device has successfully reset, the "System Status" will read "0." Click "Reset GUI" if
necessary. To make the factory defaults permanent, the user must click "Save Parameters to Flash."
In the System ID field, the firmware version is represented in a major/minor format. It also specifies the hardware version.
System ID/Description: Click "Edit" to edit/change the description of the system. If you click "System Reset," the previous descrip¬
tion will be set for the system. To make this permanent, you must click "Save Parameters to Flash."
During the "Download In Progress," the GUI function buttons will be temporarily disabled.
System Information / Operation
# BLACK BOX
blackbox.com I ±1 (724) 746-5500
Reset/Update
System
Reset
DOWNLOAD
IN
PROGRESS
System/Port Param.
Save Parameters I
to Flash
I Restore Factory
Defaults
Figure 5-4. System Update.
Example of GUI firmware file: PoE576FirmwareV09_05150-9.s99 73 KB 599 File 5/15/2009 9:01 AM
Page 20
724-746-5500 | blackbox.com
Chapter 5: GUI Operation
5.3 GUI Port Description
The Port Description panel shows 16 ports. On the 8- or 16-Port PoE Gigabit Injector models, the port numbers higher than the
system port count will be shaded gray and disabled. Each section specifies the individual port descriptions for the system.
Port Description
Parametric Information
i
Port Commands
1 1 Enable/Disable All Ports 0 Detect Legacy Signature
Legacy Detect is Enabled
1
Send Port Control
□
Port 1
Port 2 Port 3 Port 4 Port 5
Port 6 Port 7
Port 8
Port 9
Port 10
Port 11
Port 12
w
i Mv v i
w top
toP
•
m
m
w
Port
Description
\ Edit I
| Edit || Edit || Edit || Edit |
| Edit 11 Edit
| Edit I
1 Edit |
| Edit I
1 Edit |
1 Edit I
Enable
0
0 0 0 0
0 0
0
0
0
0
0
Port 13
Port 14 Port 15 Port 16 Port 17
Port 18 Port 19
Port 20
Port 21
Port 22
Port 23
Port 24
toP # # #
0 0
0
0
0
0
Description
| Edit 11 Edit 11 Edit 11 Edit |
Edit || Edit
Edit |
| Edit |
| Edit
1 Edit |
1 Edit |
Enable
0
000
LED Key [Port status!
NOTE: To send changes made in this section to the PoE
Detecting Disable/Error Port Connected
system, click on 'Send Port Control'.
to
0
top
Figure 5-5. Port Description.
To enable changes to the port configuration in this section, click the "Send Port Control" button. It will send the port information
to the unit for 16 ports. Allow the GUI 10 seconds to refresh.
Port Description: Click "Edit" to edit/change the description of the port. Click "OK" to set the description on the GUI screen. If
you click "Cancel," the previous description will be set for that particular port. Click "Send Port Control" to send the descriptions
to the system. To make this permanent, you must click "Save Parameters to Flash."
Enable: This check box can administratively enable or disable the selected port. If you select the "Enable/Disable All Ports" check¬
box, all ports will be enabled. Initially, the checkbox is not checked, by default all ports are enabled. Click "Send Port Control" to
send the command to the system. To make this permanent, you must click "Save Parameters to Flash."
If "Detect Legacy Signature" checkbox is selected, all ports are enabled and the firmware will try to detect legacy devices. By
default, legacy detection is disabled. The message in blue states that the "Legacy Detect is Enabled" (Figure 5-5). Click "Send
Port Control" to send the command to the system. To make this permanent, you must click "Save Parameters to Flash."
The different colored LEDs show the status of the individual ports. A Yellow LED shows the port is detecting or ready to be con¬
nected. A Red LED shows the port as Disable/Error. A Green LED shows that the port is connected to a compliant load.
LED Key (Port status)
Detecting Disable/Error
Port Connected
Figure 5-6. LED key (port status).
724-746-5500 | blackbox.com
Page 21
802.3af and 802.3at PoE Gigabit Injectors
5.4 GUI Parametric Information
This section allows users to review, but not edit, parametric information for each port.
Port Description
Parametric Information
Port 1
Port 2
Port 3
Port A
Port 5
Port 6
Port 7
Port 8
Port 9
Port 10
Port 11
Port 12
Discovery R KKQ
131070
131070
131070
25208
131070
131070
25120
131070
131070
24358
131070
Oi scc-vet y C
(uF]
(uFJ
(uF)
(uF)
[uF]
(uFJ
(uF)
(uF)
(uFJ
(uF)
(oF)
Current im A i 1
0
0
0
12
0
0
31
0
0
11
0
Voltage (Vi 1
2.8
2.8
2.8
57.1
2.9
2.8
57.1
2.7
2.7
56.9
2.9
0
0
0
685
0
0
1770
0
0
625
0
Current
' - I i /, „" : 't_: ? __ *• _ _L i 1 v . j ^***%& _ 1 ^
Port 13
Port 1 A
Port 15
Port 16
Port 17
Port 18
Port 19
Port 20
Port 21
Port 22
Port 23
Port 24
Discovery R
131070
131070
131070
25208
(ohm)
(ohm)
(ohm)
(ohm)
(ohm)
(ohm)
(ohm)
(ohm)
Discovery C
(oF)
(uF)
(oFJ
(oF)
(oF)
(uF]
(«F)
(oF)
(uF)
(uF)
(oF)
(oF)
Current (mA)
0
0
0
14
ImAl
ImAl
ImAl
ImAl
ImAl
ImAl
ImAl
ImAl
Voltage (V)
2.7
2.9
2.7
56.9
(V)
(V)
(V)
M
M
M
(V)
(V)
Power (mW)
0
0
0
796
|mW|
[mWl
[mW]
(mWl
[mW|
Class Current
0
0
0
0.6
(mA)
(mA)
(mA)
(mA)
(mA)
(mA)
(mA)
(mA)
Determined Class
Class
Class
Class
Class
Class
Class
Class
Class
Figure 5-7. Parametric information.
The Port Parametric Information panel displays the following set of parameters:
• Discovery R (ohms): This value represents the discovered resistance of the port in ohms.
• Current (mA): This value represents the current (I) of the port in milliamps
• Voltage (V): This value represents the voltage (V) of the port.
• Power (mW): This value represents the power of the port in milliwatts.
• Class Current (mA): This value represents the class current of the port in milliamps.
• Determined Class: This value represents the class of the discovered device.
NOTE: In Figure 5-7, Ports 1, 5, 8, 11, and 16 are connected to a compliant loads while Ports 2, 3, 4, 6, 7, 9, 10, 12, 13, 14, 15 are
ready to be connected. Ports 17-24 are not supported by this unit.
Page 22
724-746-5500 | blackbox.com
Chapter 6: Troubleshooting
6. Troubleshooting
If you have problems with the PoE Gigabit Injector, verify the following:
NOTE: The troubleshooting solutions provided can only solve minor problems. If your problem is not listed, contact Black Box
Technical Support at 724-746-5500. All up-to-date contact information can be found on our Web site,
www.blackbox.com.
Problems/Solutions
Problem: PoE Gigabit Injector does not power up.
Possible Solution #1: Make sure the AC power cord is connected.
Possible Solution #2: Make sure the AC power cord is in good condition.
Possble Solution #3: If solutions 1 and 2 do not solve the problem, then disconnect the AC power cord and reconnect. Observe
Port LEDs to verify proper power up.
Problem: AC LED is not lit.
Possible Solution: Verify that the PoE Gigabit Injector is properly connected to an AC power source.
Problem: Port LEDs do not light green.
Possible Solution #1: Port may be disabled and needs to be enabled using the GUI. Make sure the ports are enabled, then
"Save Flash Parameters."
Possible Solution #2: Make sure the ports are connected to a network.
Problem: The GUI window does not update port status.
Possible Solution: Click "System Reset" and wait for the system to reboot.
Other Problems: Please verify the following:
1. Power is applied to the PoE Gigabit Injector.
2. The network Ethernet cable is connected to the Data port.
3. The powered device's Ethernet cable is connected to the Data and Power port.
4. Make sure you are using straight-pinned Ethernet cable; do not use crossover-type Ethernet cable.
5. Cable pairs are connected to corresponding ports.
724-746-5500 | blackbox.com
Page 23
Chapter 802.3af and 802.3at PoE Gigabit Injectors
Appendix A. Optional Ethernet Interface
PC-to-Network-to-PoE Gigabit Injector:
PoE Gigabit
Injectors
Figure A-1. PC-to-Network-to-PoE Gigabit Injector diagram.
A.1 Network Interface Setup
NOTE: Using CAT5 cable, connect the PC to a network of PoE Gigabit Injectors. Skip Step 1 if you will use the Black Box GUI to
communicate with the PoE Gigabit Injector.
1. Visit ftp.blackbox.com to download the latest SNMP MIB for the network interface.
2. The SNMP MIB file named Blackbox.mib will be sent to you in an email.
If you choose to use your own SNMP console, please rename the SNMP MIB text file to the file extension that matches your
SNMP console. Follow the instructions for your SNMP console to install the MIB file.
Please check ftp.blackbox.com occasionally for the latest updates for the MIB and SNMP firmware.
Example of a SNMP Firmware file (please check our Web site for updates).
2. Visit ftp.blackbox.com to download the Ethernet Manager tool (etm.exe). Etm.exe is a Device Management Utility that runs
under the Windows 32-bit environment and is used to set up the IP address, subnet mask, and MAC address of your SNMP
device. For more advanced setup settings, use Internet Explorer or another Internet Browser.
NOTE: Your IP address may be different from the example shown in Figure A-2.
3. Execute etm.exe Ethernet Manager tool
4. Make sure the connection path between your PC and the PoE Gigabit Injector is working; the Ethernet Manager tool will
detect your SNMP device.
Page 24
724-746-5500 | blackbox.com
Appendix A: Optional Ethernet Interface
Figure A-2. Ethernet manager screen.
5. If your device is not found, check the connection and click "View"—> "Refresh." See Figure A-3.
Figure A-3. Refresh Ethernet manager screen.
724-746-5500 | blackbox.com
Page 25
802.3af and 802.3at PoE Gigabit Injectors
A.2 Advanced Setup Options
For advanced setup configuration, click "Config"—>"Device Settings" OR type the IP address in your Internet browser. Your
Internet browser will open with the following window:
Figure A-4. Controller login screen.
1. Click Setup Login
2. Default User: admin (lower case)
3. Default Password: (leave area blank)
NOTE: If you forget your login password, contact Black Box Technical Support at 724-746-5500. For up-to-date contact
information, visit our Web site, www.blackbox.com.
Page 26
724-746-5500 | blackbox.com
Appendix A: Optional Ethernet Interface
A.3 Controller Setup
htt| 10.6.225.53
v SI!*T X |t»Bing
File Edit View Favorites Tools Help X ^ »
^Favorites ££ Suggested Sites 7 C Free Hotmail ® Web Slice Gatery v
$ Configuration
’ E) CZ1 ’ Page - Safety * Tools -
# BLACK BOX
blackbox.com | +1 (724) 746-5500
Device Configuration
saus Status
Port
Enabled
Voltage
Current
Power
Status
Port
Enabled
Voltage
Current
Power
Status
1
On
OV
0 mA
OmW
Normal
13
On
2 V
0 mA
OmW
Normal
2
On
2 V
0 mA
OmW
Normal
14
On
OV
0 mA
0 mW
Normal
3
On
2 V
0 mA
OmW
Normal
15
On
2 V
0 mA
OmW
Normal
4
On
2 V
0 mA
OmW
Normal
16
On
2 V
0 mA
OmW
Normal
5
On
2 V
0 mA
OmW
Normal
17
-
-
-
-
-
6
On
2 V
0 mA
OmW
Normal
18
-
-
-
-
-
7
On
2 V
0 mA
OmW
Normal
19
-
-
-
-
-
8
On
2 V
0 mA
OmW
Normal
20
-
-
-
-
-
9
On
2 V
0 mA
OmW
Normal
21
-
-
-
-
-
10
On
2 V
0 mA
OmW
Normal
22
-
-
-
-
-
11
On
3 V
0 mA
OmW
Normal
23
-
-
-
-
-
12
On
2 V
0 mA
OmW
Normal
24
-
-
-
-
-
| Send Command | p ort 1 _v Command Port Enable ~*1
Figure A-5. Controller main window.
Port Status:
The main window of the controller is a simple GUI that allows the user to enable and disable PoE Gigabit Injector ports. It is also a
limited display of parametric information. A more complete list of parametric information is available using the Black Box GUI soft¬
ware available at ftp.blackbox.com.
724-746-5500
blackbox.com
Page 27
802.3af and 802.3at PoE Gigabit Injectors
A.3.1 System Administration
1/2 Configuration - Windows Internet Explorer [J
. v & 10.6.225.53
v j ^ X \S> Bing
File Edit View Favorites Tools Help X Jr]
Favorites 0 ’ C Tree Hotmail ^ ’
0 Configuration
^ T 0 G3 isa ’ Page» Safety * Tools *
I?; -
#BLACK BOX
blackbox.com | +1 (724) 746-5500
Device Configuration
Administrator
1 admin
System
Password
1 1
IP Address
192.168.1.100
Subnet Mask
2552552550
Gateway
1
DNS Server
168.95.192.1
DHCP Client
| Enable v
System Tools
Firmware Backup
| Backup J
Firmware Update
| Update J
Restore Default Settings
[ Default j
Reboot System
[ Reboot |
Figure A-6. Controller System Administration screen.
NOTE: If you change the Administrator name and password, make sure to write it down in a safe place for reference.
Click ^ ave to make any changes permanent.
OK Settings have been saved successfully
Back
Reboot
Click
Reboot
to reboot the system with the new changes. This may take a few minutes depending on the connection speed.
Check the PoE Gigabit Injector IP Address again as it may have changed depending on the user settings for DHCP client.
Click
Back
to review or make additional changes.
Page 28
724-746-5500 | blackbox.com
Appendix A: Optional Ethernet Interface
Configuration Description
Table A-1. Controller Setup.
Item
Default Settings
Description
Administrator
Admin
The login administrator is a user-defined name that is used at login. Write
down your new Login name in a safe location for future use.
Password
(Blank)
The login password can be empty or 1-14 characters long. Please write down
your new password in a safe location for future use. The password is also
used while performing SNMP Firmware updates.
IP Address
192.168.1.111
Four groups of numbers assigned by the network server (DHCP mode
Enabled) or user defined (DHCP mode disabled).
Subnet Mask
255.255.255.0
Four groups of numbers assigned by the network server (DHCP mode
enabled) or user defined (DHCP mode disabled).
Gateway Address
192.168.0.1
Four groups of numbers assigned by the network server (DHCP mode
enabled) or user defined (DHCP mode disabled).
DNS Server
168.95.192.1
Four groups of numbers assigned to the network server.
DHCP Client
Enable
The default setting (Enable) sets the DHCP client in Dynamic mode. Dynamic
mode allows the network server to automatically assign the IP address, sub¬
net mask, and gateway address.
If the DHCP client is set to disable the DHCP client is set to Static mode. Static
mode allows the user to manually assign the IP address, subnet mask, and
gateway address.
NOTE: If the user manually assigns the IP address, the DHCP client must be
set to Disable.
System Tools
Firmware Backup: Click the Backup button and you will get a pop-up to save a BIN file of the current firmware and settings.
Save in a location that will be easy for you to remember and rename the file to a name you will remember.
*> BLACK BOX
klarl/kAv rnm I _i_1 «00
File Download
Do you want to save this file, or find a program online to open
it?
Name: ROM.bin
Type: Unknown File Type, 4.00MB
From: 10.6.225.53
Find
t,
Save
Cancel
While files from the Internet can be useful, some files can potentially
harm your computer. If you do not trust the source, do not find a
program to open this file or save this file. What's the risk?
DHCP Client
Firmware Backup
Firmware Update | Update '
Figure A-7. Controller firmware backup screen.
724-746-5500 | blackbox.com
Page 29
802.3af and 802.3at PoE Gigabit Injectors
Firmware Update: Click Update to install the most recent firmware for your PoE Gigabit Injector or to re-install a firmware that
was backed-up. Before proceeding with this step, make sure that the connection between the PC and PoE Gigabit Injector is
secure and will not be interrupted because this may take a few minutes.
[ Back | [ Update |
Figure A-8. Controller firmware update screen.
Click "Browse," then locate your firmware file (it will have a .bin file extension). Then click "Update."
Firmware file example: ROM.bin 4,096 KB BIN File 7/29/2009 10:42 AM
Restore Default Settings: This function is used to revert back to the default settings for the firmware. This will undo any changes
that you've so far made to the firmware configuration. After using this function, users will have the option to go back or to
reboot their system.
Reboot System: This function will reboot the system. This screen will display:
Please wait 15 seconds while the system is rebooting!
Once the system has finished rebooting, it will revert back to the GUI main screen.
Page 30
724-746-5500 | blackbox.com
Appendix A: Optional Ethernet Interface
A.3.2 SNMP Settings
The new SNMP v3 has added security features that were not found on previous versions of the management protocol. These
include additional password protection.
^.. 10,6.225,53
v L *» X fe
File Edit View Favorites Tools Help
yg Favorites | ^ ]
• E Free Hotmail
0 Configuration
T
* 0 ■ □ (•■0 » Page * Safety» Toe
Status
System
SNMP
SNMP Setting
#’BLACK BOX
blackbox.com | +1 (724) 746-5500
Device Configuration
SNMP Versions
Community String
User
Authentication Mode
Authentication Password
Privacy Mode
Privacy Password
Trap hosts
VI □ V2 □ V3 0
it public
set | private
Figure A-9. Controller SNMP settings.
Table A-2. SNMP settings.
Item
Default Settings
Description
SNMP Versions
V1/V2/V3
This function describes the current version of SNMP management
that the user is running. This version is V3.
Get Community String
Public
Set option to public or private.
Set Community String
Private
Set option to public or private.
User
Admin
Logon name that may be defined by the user. If you change it, write it
down in a safe place for future reference.
Authentication Mode
HMAC-MD5
Set encryption to HMAC-MD5 or HMAC-SHA1.
Authentication Password
(blank)
User-defined password may be left blank or 1-18 characters in length. If
you change it, write it down in a safe place for future reference. This
option may be used in place of the community string.
Privacy Mode
CBC-DES
Option to set privacy encryption to CDC-DES or CFB-AES-128.
Privacy Password
(blank)
User-defined password may be left blank or 1-18 characters in length. If
changed, the information should be written in a safe place for future ref-
erence. This option may be used in place of the community string.
724-746-5500 | blackbox.com
Page 31
802.3af and 802.3at PoE Gigabit Injectors
Item
Table A-2 (Continued). SNMP settings.
Default Settings
Description
Trap Hosts
0 . 0 . 0.0
0 . 0 . 0.0
0 . 0 . 0.0
0 . 0 . 0.0
Trap hosts are the destination IP addresses that you want the traps to be
sent to. You can set the IP addresses in this Controller Setup or by using
HyperTerminal.
NOTE: The trap notifications are black from entering through the Windows firewall. Configure the Windows firewall settings to
allow incoming network connections by adding a specific program (i.e. the SNMP Console).
If the user is using the Authentication and Privacy passwords, they must remember these to use the Black Box GUI. Open the
Black Box GUI and locate and click the "Setting" button. (See Figure A-10.)
Connection Information
Figure A-10. GUI connection information.
A pop-up for the User Security Parameters will allow you to enter the correct IP Address of your PoE Gigabit Injector. If the user is
using the Authentication and Privacy Passwords ensure that SNMPv3 is checked and enter in the correct passwords in the spaces
provided. Ensure that the user also matches the name entered in the controller setup.
Figure A-11. GUI User Security Parameters screen.
If you want to run your SNMP device in Static mode, you can also configure your IP address and subnet mask through the
Ethernet Manager tool (etm.exe).
Click Config—>IP Address
NOTE: From the System Setup menu in the controller, your DHCP client setting must be Disable.
Page 32
724-746-5500 | blackbox.com
Appendix A: Optional Ethernet Interface
Figure A-12. Ethernet Manager Set IP Address screen.
A.4 DHCP Client: Dynamic or Static Mode
Check your Local Area Connection Status:
Properties
Figure A-13. Local Area Connection Status.
. Double-click Internet Protocol (TCP/IP) to view the properties. If the DHCP Client is set to "Disable," it is in
Click on
Static mode. You can manually set the IP address, subnet mask, and gateway address for your PC. If the DHCP client is set to
"Enable," it is in Dynamic mode (obtain an IP address automatically). The network will automatically set the IP address, subnet
mask, and gateway address for your PC.
724-746-5500 | blackbox.com
Page 33
802.3af and 802.3at PoE Gigabit Injectors
Figure A-14. Local Area Connection Properties/Internet Protocol Properties screen.
A.5 Setup NIC PoE Gigabit Injector with Black Box GUI
Locate the Black Box PoE GUI on your desktop or from your Start menu.
Step 1: Choose Connection Type: SNMP/LAN & WAN and click j Setting ] to access User Security Parameters. Users should
be sure to input the exact device IP address.
OR
Figure A-15. GUI User Security Parameters screens.
Page 34
724-746-5500
blackbox.com
Appendix A: Optional Ethernet Interface
NOTE: Make sure that you are using either the community string or SNMPv3 encrypted passwords set via the controller system
setup, or the GUI will not detect the PoE Gigabit Injector. To verify the IP address for your PoE Gigabit Injector, use the
Ethernet Manager tool mentioned in earlier sections.
Figure A-16. GUI User Security Parameters/Ethernet Manager screen.
Step 2: Select Search PoE: If a Black Box PoE device is found, click to select the device.
Connection Information
Connection Type
SNMP/LAN & WAN v
Setting
Search PoE
10.6.225.53 *** LPJ016A-T
Figure A-17. GUI Connection Information screen.
724-746-5500 | blackbox.com
Page 35
802.3af and 802.3at PoE Gigabit Injectors
NOTE: The IP address will be saved internally for the next use.
Figure A-18. GUI main window.
All features except for the Firmware Download are supported. Please refer to Chapter 5 for the full description of the Black Box
GUI features. To update firmware using SNMP, refer to Section A.3.
Page 36
724-746-5500
blackbox.com
Appendix B: SNMP MIB Controls
Appendix B. SNMP MIB Controls
Black Box registered Enterprise ID: 2.3.6.1.4.1.24852
SNMP Version: SNMPv3
TCP, UDP Port: 161 SNMP (Simple Network Management Protocol)
Table B-1. SNMP MIB.
OID
Name
Type
Value
Description
2.3.6.1.24852.2.2.1.0
poeSystemActionHubReset
INTEGER
ready (0)
reset (1)
Reset the PoE controller.
2.3.6.1.24852.2.2.2.0
poeSystemActionHubRestoreFactoryDefault
INTEGER
ready (0)
restore (1)
Restore factory defaults.
2.3.6.1.24852.2.2.3.0
poeSystemActionHubSaveConfiguration
INTEGER
ready (0)
save (1)
Save the PoE parameters
to Flash.
2.3.6.1.24852.2.2.4.0
poeSystemAIIPortPowerEnable
INTEGER
ready (0)
disable (1)
enable (2)
Setting this object at a
value enable (2) enables
detection mechanism for
all ports.
Setting this object at a
value disable (1) disables
detection mechanism for
all ports.
2.3.6.1.24852.2.2.6.0
poeSystem HWVersion
Displaystring
Read-only
System hardware version
for the main board.
2.3.6.1.24852.2.2.7.0
poeSystemNumberOfChannel
INTEGER
Read-only
Number of ports available
in the system.
2.3.6.1.24852.2.2.8.0
poeSystem Prod uctPartN u m ber
INTEGER
Read-only
LRJ008A: 8
LRJ016A: 16
LRJ024A: 24
2.3.6.1.24852.2.2.10.0
poeSystemFirmwareVersion
Displaystring
Read-only
System firmware version
for the PoE.
2.3.6.1.24852.2.2.11.0 poeSystemDescription
Displaystring
(SIZE (0..10))
Read-write
System description,
maximum length of 10
characters.
2.3.6.1.24852.2.2.12.0 poeSystemConsumptionPower*
INTEGER
Read-only
Measured power usage
expressed in watts.
2.3.6.1.24852.2.2.13.0 poeSystemControlACPower*
INTEGER
Read-write
Sets the value of available
power in watts to be
supplied by primary (AC)
power source.
Currently disabled. Reserved for future use.
724-746-5500 | blackbox.com
Page 37
802.3af and 802.3at PoE Gigabit Injectors
OID
Name
Table B-1 (Continued). SNMP MIB.
Type Value Description
2.3.6.1.24852.2.2.14.0 poeSystemControlDCPower***
2.3.6.1.24852.2.2.15.0 poeSystemControlBothPower***
2.3.6.1.24852.2.3.1.1.1-24 poePortlndex
2.3.6.1.24852.2.3.1.2.1-24 poePortPowerEnable
2.3.6.1.24852.2.3.1.3.1 -24 poePortControlMaxPower***
2.3.6.1.4.1.24852.2.3.1.4.0 poePortCurrentStatus***
INTEGER Read-write
INTEGER Read-write
INTEGER Read-only
INTEGER Disable (1)
(1.2147483647) Enable (2)
Sets the value of available
power in watts to be sup¬
plied by secondary (DC)
power source.
Sets the value of the total
available power in watts
to be supplied by both
power sources.
A unique value for each
port.
Setting this object at a
value enable (2) enables
the detection mechanism
for this port.
INTEGER
INTEGER
Setting this object at a
value disable (1) disables
the detecton mechanism
for this port.
Read-write This command specifies
the maximum power in
[watts] to the port.
undercurrent(l) Describes a current port
overCurrent(2) status related to the
both(3) power generation. The
ok(4) value undercurrent(l)
indicates that the port
current is below the mini¬
mal value since the attri¬
bute was last cleared.
The value overCurrent(2)
indicates that the port
current exceeds the maxi¬
mum value since the attri¬
bute was last cleared. The
value both(3) indicates
that both undercurrent
and overCurrent were
detected since the attri¬
bute was last cleared. The
value ok(4) indicates nei¬
ther an undercurrent or
an overcurrent condition
has been detected since
the attribute was last
cleared.
Page 38
724-746-5500 | blackbox.com
Appendix B: SNMP MIB Controls
Table B-1 Continued). SNMP MIB.
OID Name
2.3.6.1.24852.2.2.14.0 poeSystemControlDCPower***
2.3.6.1.4.1.24852.2.3.1.5.0 poePortCurrentStatusClear***
2.3.6.1.4.1.24852.2.3.1.6.1 ~24 poePortDescription
2.3.6.1.4.1.24852.2.3.1.7.1 ~24 poePortDetectionStatus***
2.3.6.1.4.1.24852.2.3.1.8.1 -24 poePortPowerClassifications***
2.3.6.1.4.1.24852.2.3.1.9.1- 24 poePortPowerDetectionControl*
2.3.6.1.4.1.24852.2.3.1.10.1 -24 poePortPowerPriority***
2.3.6.1.4.1.24852.2.3.1.11.1 -24 poePortPower
2.3.6.1.4.1.24852.2.3.1.12.1 -24 poePortVoltage
2.3.6.1.4.1.24852.2.3.1.13.1- 24 poePortCurrent
2.3.6.1.4.1.24852.2.3.1.14.1 -24 poePortResistance
*** Currently disabled. Reserved for future use.
Type
Value
Description
INTEGER
Read-write
This attribute is cleared
through the powerPort-
CurrentStatusClear action.
INTEGER
off(1)
clear(2)
Setting the value of this
object to clear(2) clears
the value of the poePort-
Status and enables the
agent to update the poe-
PortStatus. During Read
operation, this value will
be off(1).
Displaystring
(SIZE (0..10))
Read-write
Describes the port.
INTEGER
Read-only
Off(O)
DiscR(l)
DiscC(3)
RampUp(4)
RampDown(5)
Samplel(8)
SampleV(9)
INTEGER
Read-only
ClassO(l)
Classl (2)
Class2(3)
Class3(4)
Class4(5)
INTEGER
Read-write
Controls the port power
detection control.
INTEGER
Critical(l)
High(2)
Low(3)
Sets port priority.
INTEGER
Read-only
Port power reading (in
m Watts).
INTEGER
Read-only
Port voltage reading (in
volts).
INTEGER
Read-only
Port current reading (in
mAmps).
INTEGER
Read-only
Port resistance reading (in
ohms).
724-746-5500 | blackbox.com
Page 39
802.3af and 802.3at PoE Gigabit Injectors
Table B-1 (Continued). SNMP MIB.
OID
Name
Type
Value Description
2.3.6.1.4.1
.24852.2.4.1.1.1-24
poeTrapsControlGroupIndex
INTEGER
Not-accessible Uniquely describes the
(0.65535) group the trap control is
located.
2.3.6.1.4.1
.24852.2.4.1.2.1-24
porTrapsControlEnable
INTEGER
Trapsdisabled(l) Enables and disables the
TrapsEnabled(2) trap from the agent.
OID
Name
Type
Description
2.3.6.1.4.1
.24852.2.5.1
poePortElWFailTrap
NOTIFICATION
Hardware failure trap.
2.3.6.1.4.1
.24852.2.5.2
poePortPeakOverCurrentTrap
NOTIFICATION
Peak overcurrent trap.
2.3.6.1.4.1
.24852.2.5.3
poePortOverloadTrap
NOTIFICATION
Overload trap.
2.3.6.1.4.1
.24852.2.5.4
poePortDiscoveryFailTrap
NOTIFICATION
Discovery failure trap.
2.3.6.1.4.1
.24852.2.5.6
poePortDisconnectTrap
NOTIFICATION
Port disconnect trap.
2.3.6.1.4.1
.24852.2.5.7
poePortVoltageFailTrap
NOTIFICATION
Port voltage fail trap.
The Ethernet interface that the PoE Gigabit Injector performs under is TCP/IP, UDP port of 161. UDP port 161 for SNMP is an offi¬
cial IANA registered EDP port number. While attempting to connect to the Ethernet interface PoE Gigabit Injector via a different
network domain, you must acknowledge that the local network supports the UDP port 161.
Different Network Domain
Network Domain
3rd floor 192.168.xxx
2nd floor 192,168.2.xxx
1st floor 192.168.1.xxx
Building #1 Network Domain
192.168.xxx
Figure B-1. Network Domain Diagram.
Page 40
724-746-5500 | blackbox.com
Appendix B: SNMP MIB Controls
Description of Figure B-1:
• Building #1 has one main network server that links all three floors together.
• Building #2 has one main network server with the network domain of 254.168.2.xxx.
Different methods of connection:
NOTE: Access control from the controller setup is disabled (allowing all access).
Connection within the same network domain. (Refer to the diagram above Building #1 in Figure B-1.) For example:
• The Ethernet PoE Gigabit Injector is connected to the network domain of 192.169.1 .xxx located on the 1st floor. All computers
connected to the network domain of 192.168.1.xxx can communicate with the Ethernet PoE Gigabit Injector.
• The Ethernet PoE Gigabit Injector remains connected on the network domain of 192.168.1.xxx. Since Building #1 has a main
network server that links all three floors together, the computers on the second (192.168.2.xxx) and third (192.168.3.xxx) floors
can also communicate with the Ethernet PoE Gigabit Injector.
Connection between different network domains. (Refer to the diagram above Building #2 in Figure B-1.) For example:
• The Ethernet PoE Gigabit Injector is connected to the network domain of Building #1 (192.168.1.xxx) would like to communicate
with the Ethernet PoE Gigabit Injector from Building #1. Building #1 must configure the main network server to allow access
from an outside source, in this case Building #2. Building #1 must be able to support UDP port 161, for SNMP. Once the access
is allowed, Building #2 can communicate with the Ethernet PoE Gigabit Injector.
724-746-5500 | blackbox.com
Page 41
802.3af and 802.3at PoE Gigabit Injectors
Appendix C: Frequently Asked Questions
Question: What happens if I forget my username and passwords for the Ethernet interface?
Answer: Contact Black Box Technical Support at 724-746-5500 or [email protected].
Question: What is the function of the "current share" pin on the CD power connector? Are there any protocols or procedures
associated with it?
Answer: The DC solution contains 3x 500W 50V rectifier modules (1000W N+1) with custom cables available for connection
between the rectifier rack and up to four PoE Gigabit Injectors. The currently shared pin is an option that could be used
to have the power supply inside the PoE Gigabit Injector currently shared with the rectifiers. There are no protocols or
procedures associated with it other than it's designed only to work with our rectifier system, and even then it's not
perfect sharing because of the inrush limiting components inside the PoE Gigabit Injector located on the DC input.
Question: What type of display properties settings are required to run the Black Box SMNP v3 GUI?
Answer: 16-bit: 1024 X 768 pixels, 1280 X 1024 pixels
32-bit: 1024 X 768 pixels, 1280 X 1024 pixels
If the settings are set to the values shown below, the edges of the GUI window will be cropped.
16-bit: 640 X 480 pixels, 800 X 600 pixels
32-bit: 640 X 480 pixels, 800 X 600 pixels
Page 42
724-746-5500 | blackbox.com
Great tech support is just 30 seconds away at 724-746-5500 or blackbox.com.
# BLACK BOX
NETWORK SERVICES
About Black Box
Black Box Network Services is your source for an extensive range of networking and infrastructure products. You'll find everything
from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by
free, live 24/7 Tech support available in 30 seconds or less.
© Copyright 2011. All rights reserved.
LPJ008A-T, version 2
724-746-5500 | blackbox.com