Regency Horizon TM HZ4OE

OREGENCY Regency Horizon TM HZ4OE Gas Fireplace WARNING: If the information in these instructions are not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Installation and service must be performed by a qualified installer, service agency or the gas supplier. It,ted by. EDI Intertek Owners & Installation Manual MODELS: 14Z40E•NG1 Natural Gas I4Z40E•LP1 Propane FOR YOUR SAFETY What to do if you smell gas: • Do not try to light any appliance • Do not touch any electrical switch: do not use any phone in your building. • Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's instructions. • If you cannot reach your gas supplier, call the fire department. Installer: Please complete the details on the back cover and leave this manual with the homeowner. Homeowner: Please keep these instructions for future reference. 919 165 FM FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1144 05/29/12 EFTA00301420 MANUFACTURED MOBILE HOME REQUIREMENTS INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE This Regencr product has been tested and listed by Warnock Hersey/Intertek as a Direct Vent Wall Furnace to the following standards: VENTED GAS FIREPLACE HEATERS ANSI Z21.88-2009/ CSA 2.33-2009 and GAS-FIRED APPLIANCES FOR USE AT HIGH ALTITUDES CAN / CGA 2.17-M91. This appliance may only be installed in an aftermarket permanently located, manufactured (U.S.A only) or mobile home, where not prohibited by local codes. This Direct Vent System Appliance must be installed in accordance with the manufacturers installation instructions and the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufactured Home Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada. This appliance installation must comply with the manufacturers installation instructions and local codes, it any. In the absence of local codes follow the current National Fuel Gas Code, ANSI 2223.1 and the current National Electrical Code ANSI/NFPA 70 in the U.S.A., and the current CAN/CGA B149 Gas Installation Code and the current Canadian Electrical Code CSA C22.1 in Canada. This appliance comes equipped with a dedicated #8 Ground Lug for attachment of the ground wire to the steel chassis as applicable to local codes. The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70. or the Canadian Electrical Code, CSA C22.1. This appliance can only be used with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases. Ensure that structural members are not cut or weakened during installation. This appliance may be installed as an OEM installation in a manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer's instruction and the Manufactured Home Construction and Safety Standard, Title 24 CFR. Part 3280, in the Untied States, or the Standard for Installation in Mobile Homes, CAN/CSA Z240 Mkt, in Canada. WilkA WARNING! lir HOT GLASS WILL CAUSE BURNS DO NOT TOUCH GLASS UNTIL COOLED NEVER ALLOW CHILDREN TO TOUCH GLASS Regency HorlzonTM HZ40E Gas Fireplace EFTA00301421 To the New Owner: Congratulations! You are the owner of a state-of-the-art Gas Fireplace by REGENCY°. The HZ40E has been designed to provide you with all the warmth and charm of a fireplace at the flick of a switch. The model HZ4OE has been approved by Warnock Hersey/Intertek for both safety and efficiency. As it also bears our own mark, it promises to provide you with economy, comfort and security for many trouble free years to follow. Please take a moment now to acquaint yourself with these instructions and the many features of your Regency Fireplace. marmoithu. We recommend that our products be FIREPLACE IRSTRLITC installed and serviced by professionals who are certified in the U.S. by the National Fireplace Institute° (NFI) or in Canada by Wood Energy Technical Wood Emmy Wake leateleg NFI CERTIFIED., Training (WETT). ONE REGENCY ONE TREE TM Regency HorlzonTM HZ40E Gas Fireplace EFTA00301422 TABLE OF CONTENTS SAFETY DECAL Copy of Safety Decal REQUIREMENTS 5 4" x 6-5/8" venting High Elevation Gas Line Installation Pilot Adjustment Gas Pipe Pressure Testing 880 S.I.T. Valve Description Aeration Adjustment 35 36 36 36 36 36 AC power adaptor installation (for surefire systems) 37 MA Code - CO Detector 6 Wiring Diagram 38 (for the State of Massachusetts only) 6 proflame system GT 38 proflame system GTM 38 INSTALLATION proflame system GTMF with optional fan 39 optional fan Wiring Diagram 40 Important Message Before You Start General Safety Information Installation Checklist 8 8 8 9 Without ProFlame GTMF system Optional Remote Control Receiver Wall Switch wall mount On / Off Switch and battery compartment installation and/or receiver installation 40 41 41 42 Locating Your Gas Fireplace Heatwave Duct System Heat Release kit Clearances Mantel Clearances Mantel Leg Clearances Unit Assembly Prior To Installation Nailing Strips Installation Access panel Front face Nailing strip installation Framing Dimensions 9 9 9 10 11 11 12 12 12 12 13 GTMF remote installation Optional fan Installation Optional fan Installation - into existing installations Inner Panel Installation Glass Crystals or optional ceramic stones Optional Pebble / Crystal Installation Glass door Installation Optional mesh glass guard 4 piece faceplate installation Inner and outer door frame installation 43 46 47 49 50 51 52 53 54 55 Non-Combustible Requirements Non-combustible facing installation Framing & Finishing 14 14 15 OPERATING INSTRUCTIONS Framing & Finishing 16 Operating Instructions 56 Non-Combustible Requirements 16 First Fire 56 Exterior Vent Termination Requirements 17 Lighting Procedure 56 4" x 6-5/8" Rigid Pipe 18 Shutdown Procedure 56 Cross Reference Chart only 18 Normal Operating Sounds of Gas Appliances 56 Vent Restrictor Position 20 Copy of Lighting Plate Instructions 57 Venting Introduction 21 Maintenance Instructions 58 Venting Arrangement for Horizontal Terminations 21 Glass Gasket 58 Horizontal Terminations 22 Glass Door 58 Flex Vent 4" x 6-7/8" 22 Glass Replacement 58 Horizontal terminations 23 General Vent Maintenance 58 Rigid Pipe 4" x 6-5/8" 23 Valve assembly Replacement 59 Horizontal Terminations Rigid Pipe 4" x 6-5/8" Vertical terminations Rigid Pipe 4" x 6-5/8" 24 24 27 27 PARTS LIST Venting Arrangement for Vertical Terminations 28 Main Assembly 60 Vertical Termination with Co-Linear Flex System 29 Accessories 61 Vertical Terminations Rigid Pipe 4" x 6-5/8" Venting Arrangements - Vertical Terminations Unit Installation with Horizontal Termination 30 30 32 33 WARRANTY 4" x 6-5/8" venting 33 The Warranty: Limited Lifetime 63 Unit Installation with Horizontal Termination Unit installation with Vertical Termination 34 35 Regency Horizon"' HZ40E Gas Fireplace EFTA00301423 SAFETY LABEL This is a copy of the label that accompanies each HZ40E-NG1 and HZ40E-LP1 Direct Vent Gas Fireplace. We have printed a copy of the contents here for your review. NOTE: Regency, units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one. COPY OF SAFETY DECAL Intertek 4001172 O NATURAL GAS: Model H240E-NG1 Minimum supply pressure Manifold pressure Orifice sue Maximum input Minimum input Altitude Lined: VENTED GAS FIREPLACE HEATER! FOYER AU GAZ A EVACUATION DO NOT REMOVE THIS LABEL r NE PAS ENLEVER CETTE ETIQUETTE Certified for/Leith& pour: CANADA and U.S A. Tested to: CAN/CGA-2.17-M91(R2009) ANSI 221.88-2009/CSA 2.33-2009 MAY BE INSTALLED IN MANUFACTURED (MOBILE' HOMES AFTER FIRST SALE. litREPN.cT Serial No/ No de aerie 412 5if WC/C.E. (125IPa) 34 WCIC.E. f327IPa) IMO CA1S 26.000 Mufti (7.61 kW) 18,000 Mufti (5 28 kW) 04500 Dpi (0-1372m) O PROPANE GAS: Model HZ40E-LPI Mnimum supply pressure Manifold pressure Orifice sae MaxmLon Input Minimum Input Altitude 11' WC (2.73 kpa) 10' WC1C.E. (2491Pa) #53 CMS 25.500 Btuiti (7.47kW) 21.000 Bbih (6.15 kW) 04500 fipl (0-1372m) APPAREIL FONCTIONNANT AU NATURAL GAS CONCU POUR ETRE POELE: Mode* HZ40E-NG1 Preston mnimurn Preston a la aibulum dechappement Neves Grandeur de nnecteur Debt Calonligue maximum salon Yaltitude EQUIPE A CUISINE POUR GAZ PROPANE CONCU POUR ETRE POELE: ModeleHT.40E-LP1 Preston Minimum Presslon a b turauNre dolchapperneM elevee Grandeur de I1Mecteur DeWI Calorilque maxenum scion raktude Minimum Clearances to Combustibles I Degagement Minimum De Materisux Combustibles DOOR SEAL: Please check that the door is properly sealed Side Walls A Er (203mm) Ceiling 8 22' (559mm) Min. Mantel Height C 1r (432mm) Max. Mantel Depth 13" (330mm) Alcove Width E 84" (1524mm) Alcove Depth F 36- (2134mm) lawsuitsction Munui let minute:ens) This appliance must be inslallad n aconlance *Mb local codes. if any: if nom. Sow the National Fool Gas Code. ANSI 2223.1. cr Natural Gas and Propane Install on Code. GSA0169.1. This MpliaMe muslin :Walled ine000rdance wen me StandiedCAN:CSAZ2401M. M0bleHousino.in Canada. Or wsb me HanulachgedHolneCcoseucbonandSalgYSlandard. tee 24 CFRP(03280.in the Veiled SOWS. C. wails, SW) StaMarO PS Mt apoicams.ANSUKSBCS A225 liNFPASOI A. Mantoactured Horne IntlellatiCOS Standard C•ANSI All 9.20u NFPA SOIC standard reeRecreed4no Wades This appliamo is only forum ailh the type dips irdicalcd rolls recap plate and may be mimed n an aftermarkel. permanently lomat manufactuogrnobilaThomewhere nc4pohlaited bylocal cedes. See vanes manual fordetals. This applance d notoomembie torus, enhothareases.wiless a certifed iutisused. Installer reooenFlselonles codes ourealementsOcata. ou.en rabeence de MK Nolemerts. INICOIOS 01:la 2223.1. National FuelGasCode ouCSA43149.1 en vIgueur Installer repoereil salon le norms CAN'CSA-Z240. Sane WM. MilltiOn MOON, Ou CANCSA-Z240 VC. VOIColOS 00 CaMOIn0. Ou la tonne 24 CFR Pert 3280. ManulaCtunid HOMO Consau(ton and Safety Standard. Si ces norm*, ne pampas acclimates. utilsez le normeANSUNCSBCSA225.1/NFPA 501A. Manufactured Home Installations Standard. ouANSI AI 19 2 ou NFPASOIC Standardfor Recreational Vehicles. Cal apparel don etre dela. unouemem avec to tyDedepa2 ndiove suns plaque signeXHIgue.Cecamaret.o errs ru"s"e O&M. unBmiton preeabnqueeou moDhe le -V. SeuleclaliV)InSIfille daMtoule Si les retflaMenISIOG3us le DaMeltenl Writ WOG Cla IVIIMSSor pets pluSde fenSeirecnertS CSISCOOMII= [OS COnAutible DOurunS ulllexIbOnaveCilliti$2.aSurS. on. If CuSSOCONDS *SI Vella Thls vented gas fireplace heater is not forme wither Altars. Ne pas utikserde Niro a air avec ce foyerau pas itevacuatIon. FORUSEWITHGLASSDOORSCERTIFIEDWITH THEAPPLIANCEONLY POUR UMISATIONUMOUEMENT AVEC LESPORTESENVERRECERTIFIEESAVEC L'APPAREIL Fan (1Pala 258-911) vase," canals. Fdroon au Canals Ela-tical supply l Electrique 115VAC. 1.13A 6011t NOT FOR USE WITH SOLID FUELS.! NE PAS UTILISER AVEC DU COMEIUSTBLE SOLIDE. FPI Fireplace Products International Ltd. Delta. BC. Canada 9i#166 For the State of Massachusetts, installation and repair must be done by a plumber or gasfitter licensed in the Commonwealth of Massachusetts. For theStateof Massachusetts. flexible con- nectors shall not exceed 36 inches in length. For the State of Massachusetts, the appli- ances individual manual shut-off must be a t-handle type valve. The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720 and a CO alarm with battery back up in the same room where the gas appliance is installed. Regency HorizonTM HZ40E Gas Fireplace EFTA00301424 REQUIREMENTS MA Code - CO Detector (for the State of Massachusetts only) 5.08: flodlfleatIons to NFPA-54. Chapter 10 (2) Revise 10.8.3 by adding the following additional requirements: (a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in pan for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied: 1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or guiltier shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic. the hard wired carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level. b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements: provided, however. that during said thirty (30) day period. a battery operated carbon monoxide detector with an alarm shall be installed. 2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSUUL 2034 listed and IAS certified. 3. SIGNAGE A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled healing appliance or. equipment. The sign shall read in print size no less than one-half(1f2) inch in size. "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS". 4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signagc installed in accordance with the provisions of 248 CMR 5.08(2X2)1 through 4. (b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(8)1 through 4: 1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by the Board: and 2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes. (c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment. the instructions provided by the manufacturer for installation of the equipment and the venting system shall include: 1. Detailed instructions for the installation of the venting system design or the venting system components: and 2. A complete parts list for the venting system design or venting system. (d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases. but identifies "special venting systems", the following requirements shall be satisfied by the manufacturer: 1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation alit:Will:MS: and 2. The "special venting systems" shall be Product Approved by the Board. and the instructions for that system shall include a pans list and detailed installation instructions. (c) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment. all seating instructions. all pans lists for venting instructions. and'or all venting design instructions shall remain with the appliance or equipment at the completion of the installation. Regency Horizon"' HZ40E Gas Fireplace EFTA00301425 DIMENSIONS 45 5/8" PEW 39-13/16' 1 — . —Iv :2 1. — 364- — a , — 43X1 (1092mm 341,4- (972mm) (902m1 mew El 48. (1238mrn) 4 36" (gum.) Regency I-Icemen' 14240E Gas Fireplace EFTA00301426 INSTALLATION IMPORTANT MESSAGE SAVE THESE INSTRUCTIONS The Gas Fireplace must be installed in accordance with these instructions. Carefully read all the instructions in thismanual first. Consult the'authority having jurisdiction"todeterminetheneed for aperrnit prior tostarting theinstallation. It is the responsibility of the installer to ensure this fireplace is installed in compliance with manufacturers instructions and all applicable codes. BEFORE YOU START Safe installation and operation of this appliance requires common sense, however, we are required by the Canadian Safety Standards and ANSI Standards to make you aware of the following: INSTALLATION AND REPAIR SHOULD BE DONE BY AN AUTHORIZED SERVICE PERSON. THE APPLIANCE SHOULD BE INSPECTED BEFORE USE AND AT LEAST ANNUALLY BY A PROFESSIONAL SERVICE PERSON. MORE FREQUENT CLEANING MAY BE REQUIRED DUE TO EXCESSIVE LINT FROM CARPETING. BEDDING MATERIAL,ETC.IT IS IMPERATIVETHAT CONTROL COMPARTMENTS.BURNERS AND CIRCULATING AIR PASSAGEWAYS OF THE APPLIANCE BE KEPT CLEAN. DUE TO HIGH TEMPERATURES, THE APPLIANCE SHOULD BE LOCATED OUT OF TRAFFIC AND AWAY FROM FURNITURE AND DRAPERIES. WARNING: FAILURE TO INSTALL THIS APPLIANCE CORRECTLY WILL VOID YOUR WARRANTY AND MAY CAUSE A SERIOUS HOUSE FIRE. CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES. ESPE- CIALLY THE FIREPLACE GLASS. AND SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION. YOUNG CHILDREN SHOULD BE CARE- FULLY SUPERVISED WHEN THEY ARE IN THE SAME AREA AS THE APPLI- ANCE. TODDLERS.YOUNG CHILDREN AND OTHERS MAY BE SUSCEPTIBLE TO ACCIDENTAL CONTACT BURNS. A PHYSICAL BARRIERS IS RECOMMEND- ED IF THERE ARE AT RISK INDIVIDUAL IN THE HOUSE. TO RESTRICT ACCESS TO A FIREPLACE OR STOVE. INSTALL AN ADJUSTABLE SAFETY GATE TO KEEP TODDLERS, YOUNG CHILDREN AND OTHER AT RISK INDIVIDUALS OUT OF THE ROOM AND AWAY FROM HOT SURFACES. CLOTHING OR OTHER FLAMMABLE MATERIAL SHOULD NOT BE PLACED ON OR NEAR THE APPLIANCE. GENERAL SAFETY INFORMATION 1) The appliance installation must conform with local codesor, in theabsenceof localcodes, with the current Canadian or National Gas Codes. CANI -B149orANSI Z223.1 Installation Codes. 2) The appliance when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes with the current National Electrical Code. ANSI/NFPA 70 or CSA C22.1 Canadian Electrical Code. 3) See general construction and assembly instructions. The appliance and vent should be enclosed. 4) This appliance must be connected to the specified vent and terminationcaptotheoutside of the building envelope. Never vent to another room or inside a building. Make sure that the vent is fitted as per Venting instructions. 5) Inspecttheventingsystem annually forblockage and any signs of deterioration. 6) Venting terminals shall not be recessed into a wall or siding. 7) Any safety glass removed for servicing must be replaced prior to operating the appliance. 8) To prevent injury, do not allow anyone who is unfamiliarwiththeoperation to usethefireplace. 9) Wear gloves and safety glasses for protection while doing required maintenance. 10) Be aware of electrical wiring locations in walls and ceilings when cutting holes for termination. 11)Under no circumstance should this appliance be modified. Parts that have to be removed for servicing should be replaced prior to operating this appliance. 12) Installation and any repairs to this appliance should be done by a qualified service person. A professional service person should be called to inspect this appliance annually. Make it a practice to have all of your gas appliances checked annually. 13) Do not slam shut or strike the glass door. 14) Under no circumstances should any solid fuels (wood. paper, cardboard, coal. etc.) be used in this appliance. 15) The appliance area must be kept clear and free of combustible materials. (gases andotherflam• made vapours and liquids). Emissions from burning wood or gas could contain chemicals known to the State of Califomia to cause cancer, birth defects or other reproductive harm. Regency Horizon"' HZ40E Gas Fireplace EFTA00301427 INSTALLATION INSTALLATION CHECKLIST 1) Locate appliance a) Room location (Refer to' ocating Your Gas fireplace section) b) Clearances to Combustibles (Refer to 'Clearances" section) c) Mantle Clearances (Refer to "Mantel Clearances' section) d) Framing 8 Finishing Requirements (Refer to "Framing 8 Finishing" section) e) Venting Requirements (Refer to "Venting' section) 2) Position nailing strips (Refer to 'Unit Assembly Prior to Installation). 3) Slide unit into place. 4) Remove installation access panel. 5) Install vent (Refer to 'Venting Arrangement' sections). 6) Make gas connections (Refer to "Gas Line Installation section). 7) Make electrical connections to receptacle supplied with unit (recommended). 8) Install 4 AA batteries into receiver/switch box or use optional AC power adaptor. 9)Testthe pilot (Refer to 'PilotAdjustmenrsection). 10) TestGas Pressure (Referto"Gas Pipe Pressure Testing" section). 11) Install standard and optional features. Refer to the following sections: a) b) c) d) e) f) Glass Crystals/ Optional Ceramic Stones Optional Firebox Base Pebbles Optional Reflective Panels Optional Fan Faceplate Remote Control or Wall Thermostat and 10ft. wire harness. 12) Reinstall installation access panel. 13) Final check. Before leaving this unit with the customer, the installer must ensure that the appliance is firing correctly and operation fully explained to customer. This includes: 1) Clocking the appliance to ensure the correct firing rate (rate noted on label 26.000 Equal (NG).25.500 Btum (LP)after burning appliance for 15 minutes. 2) If required. adjusting the primary air to ensure that the flame does not carbon. First allow the unit to bum for 15.20 min. to stabilize. CAUTION: Any alteration to the product that causes sooting orcarbonIng that results In dam- age Is not the responsibility of the manufacturer. LOCATING YOUR GAS FIREPLACE 1) When selecting a location for your fireplace. ensure that the clearances are met. 2) The appliance must be installed on a flat. solid. continuous surf ace For example a wood. metal or concrete floor or in a raised (on the wall) ap- plication. The appliance must be installed on a metal or wood panel extending the full width and depth of the appliance. 3) The HZ40E Direct Vent Gas Fireplace can be installed in a recessed position or framed out into the room as in A. B. C and D. See Diagram 1. Diagram A) B) C) D) TET A Flat on Wall Flat on Wall Comer Recessed into Wall/Alcove Comer 4) This appliance is Listed for bedroom installations using the standard Remote (thermostat system). Some areas may have funher requirements. check local codes before installation. 5) The HZ40E Direct Vent Gas Fireplace is approved for alcove installations, see "Clearances" section for details. 6) We recommend that you plan your installation on paper using exact measurements for clearances and floor protection before actually installing this appliance. Have an authorized inspector. dealer. orinstaller reviewyour plans before installation. Note: For vent terminations refer to "Exterior Vent Termination Locations" section. Heat Wave asvarr---er HEATWAVE DUCT SYSTEM OPTIONAL KIT #946-556 The HeatWave Air Duct Kit increases the effectiveness of your fireplace by dispersing warm air from the ireplace to remote locations in the same room or other rooms in your home. Up to two kits may be installed on the fireplace. Please Note: Only 1 HeatWave kit may be oper- ated at one lime. This includes the internal blower option as well. alltur>"•=1.0 ," Heat Wave The HeatWave Duct Kit has different clearance andframingrequirements.cbeck the HeatWave manual for details. OPTIONAL HEAT RELEASE KIT #946-570 The Heat Release Kit expels warm air from the fireplace to the outside of the building. allowing the fireplace to be operated with less heat entering the room. The kit may be used on either the left or right side. Regency Horizon"' HZ40E Gas Fireplace EFTA00301428 INSTALLATION CLEARANCES The clearances listed below are Minimum distances unless otherwise stated: A major cause of chimney related fires Is failure to maintain required clearances (air space)to combustible materials. It is of the greatest importance that this fireplace and vent system be Installed only in accordance with these Instructions. Caution Requirements The top. back and sides of the fireplace are defined by standoffs. The metal ends of the standoff may NOT be recessed into combustible construction. WARNING Fire hazard Is an extreme risk if these clearances (air space) to combustible materials are not adhered to. It is of greatest importance that this fireplace and vent system be installed only in accordance with these instructions. Clearance: Dimension Measured From: A: Mantel Height (min.) 1T (330mm) Top of Fireplace Opening B: Sidewall (on one side) 8' :203mm: Side of Fireplace Opening C: Ceiling (room and/or alcove) 22" (559mm) Top of Fireplace Opening D: Mantel Depth (max.) 1r (330mm) 22" Above Fireplace Opening E: Alcove Width 844 (2134mm) Sidewall to Sidewall (Minimum) F: Alcove Depth 36' (914mm) Front to Back Wall (Maximum) G: From Floor 27' (686mm) Top of Fireplace Opening Note: 0" No hearth required E Alcove rife Release Kit have different clearance The HeatWave Duct Kit and the Heat iwites.•S and framing requirements. check the HeetWaveand Heat Release manual for details. lint Release MI Flue Clearances to Combustibles Horizontal Top Horiztonal . Side Horiztonal • Bottom Vertical 3" 2" Passing through wall. floor/ceiling when firestop is used. F 1 2" Installed close to ceiling. r Regency Horizon"' HZ40E Gas Fireplace EFTA00301429 INSTALLATION MANTEL CLEARANCES Due to the extreme heat this fireplace emits, the mantel clearances are critical. Combustible mantel clearances from top of front facing are shown in the diagram on the right. Note: Ensure the paintthat Is used on the mantel and the facing is"high quality" orthe paint may discolour. 14 12 10 8 6 4 2 0 llllllltlltlll 26- 20 - 10-- 0 To Unit Base 1" (25mm) 22"(559mm) 2T Top of Fireplace Opening Combustible Material Metal Stud (On Edge) Facing Non-combustible 17 Standoff 4 MANTEL LEG CLEARANCES Combustible mantel leg clearances as per diagram: 5-11/16"(144mm Non-Combustible Allowable mantel legp rojection Regency Norizonm 14240E Gas Fireplace EFTA00301430 INSTALLATION UNIT ASSEMBLY PRIOR TO INSTALLATION The nailing Strips must be correctly positioned and attached before unit is slid into position. NAILING STRIPS The nailing strips come attached to the unit. There is 1 plate on each side. on the top. There also two on the bottom. The top and side nailing strips are secured to the framing. The bottom nailing strips are IMPORTANT NOTE Framing depth measurement is noted with the nailing strips set as far forward on the firebox as possible. The nailing strips can be adjusted back up to 1 -1/24 to allow for varying thicknesses in noncombustible material & wall finishes. INSTALLATION ACCESS PANEL The unit is equipped vMh a removable access panel for pre-finish installation of optional components this panel is located on the lower front face. 1) Remove lower front face nailing strips (2 screws per nailing strip). 2) Remove 8 screws to remove access panel. 3) Easier access to gas connection with panel removed. 4) Install any optional components with access panel removed. 5) Reinstall access panel with B screws and lower front face nailing strips (2 screws per strip) - prior to installing any facing material Note: Access panel is no longer usable once fadng material installed. Installation Access Panel FRONT FACE NAILING STRIP INSTALLATION Required when the combined facingilinishing material is 112'. If using material which is thicker than 1/2'. the nailing strips are not required and should be removed and discarded. 1) The 5 front nailing strips are only used if the facing/finishing material is a combined 1/2' in thickness. This enables the fadng and finishing materials to be securely fastened to a solid surface. 2) Follow instructions on non-combustible facing installation for pre- drilling holes prior to attaching the noncombustible material supplied with this unit. 3) The sidettop nailing strips which are attached to this unit will also need to be adjusted. See Framing and finishing in this manual. Lower front nailing strips Regency Horizon"' HZ40E Gas Fireplace EFTA00301431 INSTALLATION FRAMING DIMENSIONS Framing DimensiOnS B 1) G J K L * Framing depth measu Omani is noted with the nailing strips set as far forward on the firebox as possible. The nailing ships can be adjusted back up to 1- to allow for varying thicknesses in non-combustible material & wall finishes. Description Framing Height EMMIIML_ Framing Depth* MinimCoiner Wall Depth Comer Vent Centerline Height Nona Gas Connection Opening Height Gas CSE Gas Connection Inset Gas Connection Opening Width HZ40E IME 42' (1067mm) taa C1 Horizontal Vent 19-7116' (495mm) C2 Vertical Vent 23-7/16" (596mm) Vertical rise -terminating horizontal 57-18" (1457mm) 36 - (921mm) 1r (432m01) 2" 151mm) 4 - 3/16" (106mm) --al 8. 5116' (211mm) a2" (89mm) Note: Al other framing may be of wood construction. Regency Hodzonm FiZ40E Gas Fireplace EFTA00301432 INSTALLATION NON-COMBUSTIBLE REQUIREMENTS AI three pieces (top. 2 sides) are now supplied to meet the non combustible requirements. Previously only the top was supplied Calcium silicate board is a high • grade material with cement. quartz. natural and selected minerals as the main raw materials. It is widely used for partitions and ceilings in buildings. It is fire proof and earthquake proof. II finishing the wall above the unit with materials such as tile, brick, marble. etc. non-combustible board available from the building supply store can be used. Note: Calcium Silicate is 1/2' thick Metal Stud g • • • g ;TA nE • 10' (252=1) el In 5-11/16-(144mm) 51.5116' (1303mm) NON-COMBUSTIBLE FACING INSTALLATION Caution: The noncombustible board supplied with this unit can be damaged if dropped or struck. Handle with care. 1) Using drywall screws • secure non combustible material around unit, framing and top nailing strip every 6 inches. Important Note: To avoid cracking the board • pre-drill holes prior to securing to unit/ framing. 2) Wipe any debris/dust from the non combustible material and drywall. 3) Prior to taping and mudding it is highly recommended to prime the facing using a quality primer. This will ensure proper adhesion of both the tape and mud. The supplied board is very porous. 4) Tape the seams using a mesh type tape. 5) Mud seams as normal. We recommend using a product called Durabond high strength compound • for the first coat. This product can be found at any hardware store. Mud must be cured as per manufacturers recommendations. 6) Prime wall for a second time for proper adhesion of paint 7) Paint walls using a high quality paint which will withstand the high temperatures being emitted from this appliance. Non combusIblie board Apnea v41b unt 1'Metal Stud (header) on edge ►, A Metal Stud • gen.'s...Ana bawd seised vein um. 14:0 combust/So loud MUS1 BE PRIMED. Regency Horizon"' HZ40E Gas Fireplace EFTA00301433 INSTALLATION FRAMING & FINISHING 1) Frame in the enclosure for the unit with framing material. IMPORTANT: The framed opening must be of non-combustible material. Note: When constructing the framed opening, please ensure there Is access to Install the gas lines when the unit is Installed. 2) For exterior walls, insulate the enclosure to the same degree as the rest of the house, apply vapour barrier and drywall. as per local instal- lation codes. (Do not Insulate the fireplace Itself.) WARNING: Failure to insulate and add vapor barriers to the inside of the exterior wall will result in operational and performance problems including, but not limited to: excessive condensation on glass doors, poor flame package, carbon, blue flames etc. These are not product related issues. 3) The unit does not have to be completely enclosed in a chase. You must maintain clearances from the vent to combustible materials: See "Clearances" section. Combustible materials can be laid against the side and back standoffs and the stove base. 4) Noncombustible material (ie. tile, slate. etc) may be brought upto and overlap the unit (top and bottom) ensuring that the maximum thickness does not go beyond the 1.112" as shown in the diagram below. The faceplate will not be able to be mounted if finished material is beyond 1 -1 /Y. 1-'4" (38mm) Edge of __ flange on fireplace 1/2" required between faceplate + finished wall 1:W (38mm) Nailing Strip IMPORTANT: 112" gap required between faceplate and finished wall when using 4 pee. Faceplate (Part # 256.924, 256.926, 256.927) 5) If material such as brick, stone. etc extends past the faceplate depth (1.112-). when finishing around the faceplate, the minimum opening dimensions noted below must be adhered to ensuring for the removal of the faceplate and for the safe operation of this appliance. NOTE: Spacing of 1" around the completed surround must be adhered to. 52.31C I is. if Unit shown with 4 piece faceplate 47- .1115- Unit shown with inner and outer door frame I. I E LTTi_ 39-13/16" IL • to eb Unit shown with inner door frame only Regency Norlzonm 14240E Gas Fireplace EFTA00301434 INSTALLATION FRAMING & FINISHING 1/2" 1" Nailing Strip 1/2" Forward 3" (flush) Nailing Strip 1' Forward Unit Unit `—Nailing Strip Flush w/unit Factory Set Note: Depending on the material used for finishing, the nailing strips must be set accordingly so that the finished material is always at the 1.1/2' edge of the flange. I 1 4 E V ZO? E CAn 10' (252mm) NON-COMBUSTIBLE REQUIREMENTS Metal Stud (header) on edge ► Metal Stud A • 5-11/16" 51-5/15' (1303mm) May be combustible (ie. 1/2"dryw • 33.13416• (859mni) (144mm) Regency Horizon"' HZ40E Gas Fireplace EFTA00301435 INSTALLATION EXTERIOR VENT TERMINATION REQUIREMENTS BITI0RINO110 Vent Termination Q Air Suppry Owlet E Area whet* terminal a nol perrritted Minimum Clearance Requirements Canada' USA2 A Clearance above grade. veranda. porch. deck. or balcony 12130cm) 12130cm) 8 Clearance to window or door that may be opened 12130cm) cr (23crn) C Clearance to permanently closed window ' 0 Vertical clearance to ventdated soffit located above the ternwial within a horizontal distance of 2 feet (6Icm) from the center Ike of the terminal (check with the local code) 19148cm) 19148cm) E Clearance to unventiLated soffit 19148cm) 19 '(48cm) F Clearance to outside corner: with AstroCap Termination Cap. 7118cm) 7118cm) Clearance to outside corner: with all other approved Termination Caps. 13133cm) 13133cm) G Clearance to inside corner: with AstroCap Termination Cap 7118cm) 71113cm) Clearance to inside corner: with all other approved Termination Caps. 13133cm) 13 133cm) H Clearance to each side of center line extended above metedregulator assembly 36 190cmr J Clearance to service regulator vent outlet 36'(90cm) ' K Clearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance 12130cm) r (23cm) L Clearance to a mechanical air supply inlet #3' (91cm) above if withal 10' (3rn) horizontally. 7211.8m) 36•(90cn) e fA Clearance above paved sidewalk or a paved drweway located on public property 84 12.1m)! ' N Clearance under veranda, porch. deck. or balcony 12130cm) , ' ' In accordance with current CSA 8149.1. Natural Gas and Propane Installation Code 2 In accordance with the current ANSI Z223. liNFPA 54. Nat,onal Fuel Gas Code +A vent shall not terrneste directly above a sklewak or paved driveway which is located between two single family dwellings and serves both dwellings $ Permitted only if veranda. porch, deck. or balcony S fully open on a minimum of two sides beneath the floor • Clearance in accordance with local installation codes and the requirements of the gas supplier a 3 feet (91cm) within a height of 15 feet (4.5m) above the meter 1 regulator assembly b 3 feet (91cm) above - it within 10 feet (3m) horizontally Regency Hertz:mini I4Z40E Gas Fireplace EFTA00301436 INSTALLATION 4" X 6-5/8" RIGID PIPE CROSS REFERENCE CHART ONLY Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI. Oescriptien Simpson Owed Wm pia SeIldrk Direst Terrr American Metal ProductsID AmOtIvial Died Meial-Fabm Sure Seel SecurRy Secure-Vent ICC Excel Med 8 Pipe Length-Galvanized 460VA-06 401-6 WA 406 SV4L6 TC-4DL6 8 Pipe Length-Black 460VA-069 40T-65 WA 4065 SV4L86 TC-40L6B 7- Pipe Length-Galvanized N/A WA 407 WA WA WA 7- Pipe Length-Week WA WA 4075 WA WA N/A 9" Pipe Length-Galvanized 46DVA-09 40T-9 WA WA WA WA 9" Pipe Length-Week 460VA-095 4DT.95 WA WA WA N/A 12' Plpe Length-Galvanized 46DVA-12 40T-12 4012 4012 SV4L12 TC-40L1 I2- Pipe Lengui-Black 460VA-125 40T-125 40125 40125 SV4L812 TC-II)Liti 18' Pipe Length-Galvanized 46DVA-18 407-18 4018 4018 SV4LA TC-40L18 1W Pipe Length-Black 46DVA-18B 40T-185 40185 40185 SV4LA TC-4DL 18B 24' Pipe Length-Galvanized 48WA-24 401-24 4024 4020 SV4L24 TC-40L2 24' Pipe Length-Black 460VA.245 401.245 40245 40245 SV4L524 TC-40L2B 36' Pipe Length-Galvanized 480VA-36 40T-36 4036 4036 5V4138 TC-40L3 36' Pipe Length-Black 46DVA-365 401-366 40366 40365 SV4L536 TC-40L36 48' Pipe Length-Galvanized 480VA-48 40T-48 0048 4048 SV4L48 TC-40L4 4W Pipe Length-Black 46DVA-486 401-48B 40486 40485 SV4L548 TC-40L46 60' Pipe Length-Galvanized 48WA-60 40T-60 WA N/A WA N/A EC Pipe Length-Black 460VA-606 401-60B N/A WA WA WA Adjustable Length 7-IT-Galvanized WA WA N/A 4DAL WA TC-ODLT Adustabte Length T. I 0' -Black WA WA WA 4DAL5 WA TC.4DLTB Adjustable Length T-Galvanized WA WA 4D7A WA WA N/A Adusiable Length T'-Black WA WA 407AB WA WA NA Extension PO 8-1/t-Galvanized 460VA-08A WA N/A WA WA N/A Extension Pipe El-VT-Black 46DVA-OBAB WA N/A WA WA NA Adjustable Length It-Galvanized WA WA 4012A WA SVOLA12 N/A Ackosiable Length 12'-Slack WA WA 4012A WA SV4L5Al2 NA Extensko Pipe 16*-GaNailzed 460VA-16A WA N/A WA WA NIA Extension Pipe 16'-Black 46DVA-I6AB WA WA WA WA WA 45' El3ow-Galvantzed 46DVA-E45 407-EL45 4045L WA N/A TE-40E45 45' Wbow-5lack 460VA.E456 401-EL455 40T-EL45B VA WA TE-40E458 45' Elbow Swivel-Galvanized See 460VA-E45 N/A WA 41345L SV4E45 WA 45' Ebow Swwel.Black See 46DVA.E45B WA WA 4045L5 SV4EB45 WA 90' Elbow-Galvanized 460VA-E90 401-EL9OS 40TEL9OS N/A N/A TE-40E90 90' Ebow-Black 460VA.E936 40T-EL90S5 40T-EL90S5 WA SV4EBR90.1 TE-40E90B 90' Elbow. SwIvel.Galvantzed See 460VA-E90 N/A WA 40901. SV4E90-1 WA 90' Elbow. Swivel.Black See 46DVA.E9OB WA WA 4090L5 SV4E690-1 WA 90' Starter Elbow. Swivel-Gab/awed N/A N/A WA 4090A N/A WA Adaptor' WA WA WA 4090L WA WA Ceiling Support WA 407-CS 4DFSP 40SP SV4SD 7E-4DE45 Cathedtal Support Box 46DVA-CS 40T-CSS 401156 40RS SV4CSB TE-41)E4515 Wal Support/Band 46DVA-WS 407-WS1B 4DWS 4DWS SV4BM WA Ofiset Support 46CP/A.ES (MA . FPI) 40T-OS NSA WA SV4SU WA Wal Thanble-Black 46DVA-WT 407-WT 40W7 40W1 SV4FISM 7E-4DE90 Wal Trimble Suppcit/Ceiling Supped., 460VA•DC WA NSA NA SV4PF TE-40E90B Areal* Spacer 46DVA-FS 407-FS 4DFSP 4DFS SV4BF _ WA — Trim Pate-Back WA 4DT-TP 4DEPB 40CP SV4LA WA C Regency Horizon"' HZ40E Gas Fireplace EFTA00301437 INSTALLATION Description Simpson Deceived Pro* Selldrk Direct Temp" American Metal Products:ID Arnehwer Oita Metal-Fatd" suet Sod Security Secure-Were ICC Excel Circa Attc NtolatKin She 2' 46CNA.IS MAO FPI NrA 4DAIS12 WA SV4RSA TA Attic Insulation Shield - Cold °khakis 36" N/A N/A ODAIS12 N/A N/A TM-4AS Basic Horizontal Termination Kit (A) Disc. 4DT.HKA 4DHTK2 4W-1'MA SV-SHK NA Horizontal Termination Kit (B) 46DVA-KMA tOwind mai:fent; 401-ZIKB 4DHTK1 4DHTI(B SV-HK HA Vencal Terminatim Kil Ds. 4C.T.oKC 4DHTK fo:r7K SlbFK NA High Wind Verlical Cap 46DVA-VCH WA WA Ni'. WA TM-4VT nigh Wird Horizontal Cap 46DVA.HC NA TA TVACHT Horizontal Square Termination Cap See 46DVA-HC 4DT-HiSC 4DHC 4DHT SV4CHC-I TA-4MT Vented Termination Cap 461YVA.vC 4DT.FP/C 4DVC 4DVT SV4CGV.I TM-4V7 Storm Collar 46DVA-08A 4DT-SC 4DSC 4DSC SV4FC TA-SC Adjustable Flashing OM 24212 460VA-F6 4DT-ST t4 40125 405114 SV4STCI4 TF-4FA Adjustable Mashing 6/12-12/12 46DVA-FLA 4DT-ST36 4D355 4DST36 SV4STC38 TF-4F0 Vinyl &ding Standen 46DVA.VSS 4DT-VS NrA 4DVS SV4VS PA-VSS Vinyl Siding Shield Plate N/A 4DT-VSP N/A WA SV4VS N/A Snorkel Termination 14' 46DVA.SNKL TA WA IFA NIA T.4-43714 Snorkel Termination 36- N/A NIA WA WA WA 114-4S138 Redick!' Disk NA NA NR WA TA TM-4DS Extended Vertical Termination Cap WA WA N/A NM WA N/A Chimney Corweision Kt A (USA only) 46DVA.KCA Ni WA NrA TA TM-4CA6 Chimney Conversion Ki B (USA only) 46DVA-KCB WA N/A NIA WA T.4-4CA7 Chimney Corrmesion 10 C (USA only) 46DVA.KCC Na NrA WA NIA PARCAE, Chimney Conversion Kt Masonry (USA only) 46DVA10.4C WA WA NIA WA N/A Wal Fireslop 46DVA.V/FS Na NrA WA NIA TM-SIR Cando Flex Connectors 46DVARDF WA NfA N/A WA WA FPI 946-506P Vary Guard (Optimal) for AstroCap 948-206 Vinyl Siding Shield for Riser VeM Terminal 510.994 Rigid Pipe Adaptor (Must use with all rig° piping) 946-200P Vent Guard (Opting Ice Riser Vent Terminal 640-530:P Mae( Vent Terminal 948-523V AstroCap Horizontal Cap 946-605 Starter Calm Increaser C x 8-6/V to 5' x 8' 946.206 Vinyl Siding Standoff for AstroCap Note: When using Metal-Fab Site Seal Rigid Piping - please note that the Adaptor (400A) must be used in ccojundko wkh FPI Rigid Pipe Adaptor (510-994). Offset Pipe Selection: Use this table to determine offset pipe lengths. Pipe Length 0-) V x 6.5TVenting For SpOCille insItuctions on venting °deponents - visit the manulaclurers ivebsite ISIS below.RLYI L . / / //I I ' I I Y I (X) Kee CY) 0- (0mm) 4-718-(124mm) 13-7/8' (340mm) Simpson Direct Vent Pro: 6" (152tivn) V (933mm) 16-1 /2-(419twn) Selkirk Direct-Temp: 9' (229mre) 10-L8-(257mm) 18-5/8" (473mm) American Metal Predicts 12- (3116mm) 12-1/C (3l 1mm) 20-3/4-(527mm) Metal-Fab Sure Seal: 24' (610mm) 20-5V (524mm) 29-1/8" (74Ornm) Se:Andy Secure Vent. — ' I i X36- (914mm) 29- (737mm) 37-112- (953mm) Industrial Chimney Company: 48' ( I 21 ginvn) 37-7/16' (951mm) 45-15116' i1167mm) Note: Horizontal Leis DI vent must be love. or have a VC rise or every 1 fool of tort towards the letmimtlo Never anew the vent to MIdCwaws d - this could CALM high temperatures and may present a posstl fire hazard. Regency Horizon"' 14240E Gas Fireplace EFTA00301438 INSTALLATION VENT RESTRICTOR POSITION Vent restriction is required for certain venting installations. see the diagrams in the "Venting Arrangements' section to determine if they are required for your installation. The Vent Restrictor plate is located on the inside top of the firebox. To set the vent restriction as indicated in the venting arrangements diagrams, refer to the following instructions: 1) Remove the glass door - see instructions in this manual. 2) Remove the screws that hold the vent restrictor plate in place. 3) Adjust the vent restrictor plate to the required vent restrictor position as per the diagrams shown. 4) Once the vent restrictor plate is in the required position, secure with screws. 3.000 Set 0 (Factory set) VENT RESTRICTOR AT 3' 2000 I Set 1 VENT RESTRICTOR AT 2' 1500 u—kria-u Set 2 VENT RESTRICTOR AT 1.1/2' 1.000 Set 3 VENT RESTRICTOR AT 1" C Regency HorlzonTM HZ40E Gas Fireplace EFTA00301439 INSTALLATION VENTING INTRODUCTION The HZ40E uses the "balanced flue' technology Co-Axial system. The inner liner vents products of combustion to the outside while the outer liner draws outside combustion air into the combustion chamber thereby eliminating theneed louse heatedroom air for combustion and losing warm room air upthechimney. Note: These flue pipes must not be connected to any other appliance. The gas appliance and vent system must be vented directly to the outside of the building, and never be attached to a chimney serving a separate solid fuel or gas burning appliance. Each direct vent gas appliance must use its own separate vent system. Common vent systems are prohibited. VENTING ARRANGEMENT FOR HORIZONTAL TERMINATIONS The diagram shows all allowable combinations of vertical runs with horizontal terminations. using one 90° (two 45°elbows equal one 90° elbow). (Not including the starting 45 elbow at the flue collar when using rigid venting.) Note: Must use optional rigid pipe adapter (Part# 510-994) when using Rigid Pipe Venting Systems. Horizontal (Feet) 0 2 4 6 0 10 12 I I I !II Is 16 • 14I a.0 12 E 10 0 u_ a—0 .0 6 stu 2— > 0 • VENT RESTRICTOR SETTING: Vent restrictor lac ory se at Se 0. Refer to the 'Vent Restrictor Position" section for details on how to change the vent restrictor from the factory setting of Set 0 to Set 1 if required. Vent Restrictor on Set 1 36.114' (921mm) Ainimum Height Recpinnent 14 16 18 20 Note: For horizontal terminations the Regency Direct Vent Flex System may be used for installations with a maximum continuous vent length of up to 10 feet. If longer runs are required, rigid pipe must be used. • Maintain clearances to combustibles as listed in "Clearances" section • Horizontal vent must be supported every 3 feet. • Firestops are required at each floor level and whenever passing through a wall. • A vent guard should be used whenever the termination is lower than the specified minimum or as per local codes. • Flex system can only be used up to 10 feet - otherwise rigid venting must be used. Regency Horizonw HZ40E Gas Fireplace EFTA00301440 INSTALLATION HORIZONTAL TERMINATIONS FLEX VENT 4" X 6-7/8" These venting systems. in combination with the HZ40E Direct Vent Gas Fireplace, has been tested and listed as a direct vent heater system by Warnock Hersey/ Intertek. The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram in 'Exterior Vent Termination Locations" section. Regency. Direct Vent (Flex) System Termination Kits includes all the parts needed to install the 14240E using a flexible vent. FPI Kit # Length Contains: #946-513 2 Feet 1) 6.7/8" flexible outer liner (Kit length) 2) 4' flexible inner liner (Kit length) 3) spring spacers #946-515 4 Feel 4) thimble 5) AstroCap termination cap 6) screws 7) tube of Mill Pac #946-516 10 Feet 8) plated screws 9) S.S. screws #8 x 1.1/2' drill point Notes: 1) Liner sections should be continuous without any Joints or seams. 2) Only Flex pipe purchased from Regency" may be used for Flex installations 3) Horizontal vent must be supported every 3 feet. 4) Regency"Direct Vent System (Flex)Isonlyapproved for horizontal terminations. 5) Flex system can only be used up to a maximum continuous vent length of up to 10 feet. If longer runs are required, rigid pipe must be used. Wall Thimble AstroCar 4" dia. flue pipe Termination Cap 6-7/8" (Part# 946-523/P) 173mm) .5, dia. Flue pipe spring spacer Vent Guard (Part #946-506/P) 22 Regency Horizon"' HZ40E Gas Fireplace EFTA00301441 INSTALLATION HORIZONTAL TERMINATIONS RIGID PIPE 4" X 6-5/8" The minimum components required for a basic horizontal termination are: 1 Horizontal Termination Cap 1 45° Elbow 1 Rigid Pipe Adaptor (510-994) 1 Wall Thimble 1 Length of pipe to suit wall thickness (see chart) Wall thickness is measured from the back standoffs to the inside mounting surface of termination cap. For siting other than vinyl furring strips may be used. instead of the vinyl siding standoff, to create a level surface to mount the vent terminal. The Terminal must not be recessed into siding. Measure the wall thickness including furring strips. If a Vinyl Siding Standoff is required (it must be used with vin I siding), measure to outside surface of wall without siding and add 2 inches. r i,",,ii:III inhilETii .n li Wall Thickness (inches) Vent Length Req