System Product Data Sheet

System Product Data Sheet Edition: 16.02.2011 Revision no: 0 Identification no: 01 07 03 02 System Sikadur-Combiflex® SG system Sikadur-Combiflex ® SG system High performance joint sealing system Product Description Uses High performance joint sealing system for construction, expansion and connection joints as well as for cracks. When fixed to the joint, allows irregular and high movement in more than one direction, whilst maintaining a high quality seal. The Sikadur-Combiflex t° SG system consists of a modified flexible Polyolefin (FPO) waterproofing tape with advanced adhesion and a various range of suitable Sikaduis adhesives. Sealing system for expansion. construction and connection joints. as well as for cracks in: n Tunnels and culverts n Hydro electric power plants n Sewage treatment plants n Basements n Water retaining structures and drinking water reservoirs n Around iron, steel and concrete pipes n Swimming pools Sealing of: n Joints with extreme movement n Building sections where varying settlement is expected n Cracks Repair / reinstatement of leaking joint sealing systems such as: n Waterbars n Joint sealants etc. Characteristics / n Advanced adhesion, no activation on site required Advantages n Easy to install n Suitable for both dry and damp concrete surfaces n Extremely flexible n Performs well within a wide range of temperatures n Excellent adhesion to many materials n Weather and water resistant n Available with normal and rapid hardening grades of adhesive n Root resistant n Good resistance to many chemicals n Versatile system suitable for many difficult situations 1 PDF created with pdfFactory Pro trial version www.pdffactory.com Sikedur-Combflexe SG system 1111 EFTA01121239 Tests Approval / Standards Hygiene Institut: Test report No. K-178989-09 drinking water suitability according to K1W-Guideline of the Federal Environment Agency (UBA). July 2009 Determination for resistance to roots according to CENITS 14416 Product Data Form Appearance/ Colours Sikadur-Combillex e SG-101-20 P Tape: Flexible light grey membrane Sikadur-Combiflex e SG-101-20 M Tape Flexible light grey membrane with red masking tape Sikadur-Combiflex e CF Adhesive and Secaduia-31 CF: Light grey Sikadure-31 DW: Grey Sikadur-Combiflex e SG system combi-pack Ready to use kit contains: 6 kg Sikadur-Combiflex ® CF Adhesive Type Normal 6 m Sikardur-Combiflex g SG -10 M 150 (thickness 1 mm, width 15 cm) 1 kg Sikag Colma Cleaner (for tool cleaning) Packaging Sikadure-Combillex e CF Adhesive. Sthadure-31 CF : 6 kg units (A+B) ready to use (just for Sikadurg-31 CF) 20 kg unit part A 10 kg unit part B Sikadure-31 DW 6 kg units (MB) ready to use 30 kg unit part A 10 kg unit part B Sikadur-Combiflex e SG-10 P: Thickness: 1 mm Width: 10, 15 , 20, 25, 30, 40, 50. 100. 200 cm Rolls of 25 m Sikadur-Combiflex e SG-20 P: Thickness: 2 mm Width: 15 , 20, 25, 30, 40, 50, 100. 200 cm Rolls of 25 m Sikadur-Combiflex e SG-10 M: Red masking tape Thickness: 1 mm Width: 10, 15 , 20, 25, 30 cm Rolls of 25 m Sikadur-Combiflex e SG-20 M: Red masking tape Thickness: 2 mm Width: 15, 20, 25, 30 cm Rolls of 25 m Storage Storage Conditions / Shelf Life Sikadure-Combiflex e CF Adhesive. Sikadure-31 CF and Sikadure-31 DW: 24 months from date of production if stored properly in undamaged unopened original sealed containers in dry conditions at temperatures between +5°C and +30°C. 2 PDF created with pdfFactory Pro trial version www.ocIffactory.com Sikedur-Combflexe SC system 2/11 EFTA01121240 Sikadur-Combillex e SG-101-20 P tape 36 months from date of production if stored properly in undamaged unopened original sealed containers in dry conditions at temperatures between +5°C and 4.30°C. Opened and unprotected rolls must be used within 2 month. Sikadur-Combiflex e SG-101-20 M tape (with red masking tape) 12 months from date of production if stored properly in undamaged unopened original sealed containers in dry conditions at temperatures between +5°C and 4.30°C. Opened and unprotected rolls must be used within 2 month. ■ 3 PDF created with pdfFactory Pro trial version www.pdffactory.com Sikedur-Combfleze SC system VII EFTA01121241 Technical Data Chemical Base Sikadue-Comdflee CF Adhesive. Sikadue-31 CF and Sikadue-31 DW: Modified. solvent free, filled 2-part epoxy resin Sikadur-Combiflee SG Tape: modified flexible Polyolef in (FPO) with advanced adhesion Sikadur-Combiflet SG System: -30°C min. to +40°C max. in wet conditions -30°C min. to +60°C max. in dry conditions Service Temperature Mechanical / Physical Properties Bond Strength Sikadur-Combiflet SG System (Siicadur-Combillee SG Tape glued with Sikadue- Combillee CF Adhesive) Substrate Bond Strength Concrete (dry) › 2 N/mm2 (failure in concrete) Concrete (mat / damp) > 2 N/mm2 (failure in concrete) Steel (bastdeaned) > 5 N/mm2 Peel Strength Sikadur-Combiflet SG System: Sikae System test: Sikadur-Combiflee SG Tapes bonded to each other with Sikaduea-Combiflex e CF Adhesive. Sikadure-31 CF or Sikadu0-31 DW. Results: Strength: > 6 N/mm (2 mm) Strength: > 4 N/mm (1 mm) Resistance Chemical Resistance Sikadur-Combilfee SG System (Sikadur-Combillee SG Tape glued with Sikadue- Combiftee Adhesive. Sikadur°3-31 CF and Sikadure-31 DW) Longterm to: Water, lime water. cement water, seawater. salt solutions, domestic sewage. bitumen (according to EN 1548) . bitumen emulsion coatings (staining possible) etc. Temporary to: Light fuel oil. diesel, diluted alkali and mineral acids, ethanol, methanol, petrol etc. These chemical resistance indications may be used to determine the suitability of the sealing system. Regarding specific short term chemical resistance, please consult our technical service departments. 4 PDF created with pdfFactory Pro trial version www.pdffactorv.com Sikedur-Combflexe SC system 4/11 EFTA01121242 System Information System Structure Application Details Consumption Sikadur-Combiflex e SG Tape: Sikadure-Combiflex e CF Adhesive per metre length The Sikadur-Combiflet SG System consists of the flexible Sikadur-Combiflet SG sealing tape and a Sikadut epoxy adhesive. Two types of flexible tapes are available: Sikadur-Combifiet SG-10J-20 M: with red masking tape. mainly used for expansion joints Sikadur-Combifiex ® SG-10J-20 P: without masking tape Various types of suitable Sikadure adhesives are available: Sikadue-Combiflet CF Adhesive (Type N and R) Sikadur®-31 CF (Type N, R and S) Sikadur -31 DW (mainly used for contact with drinking water) Note: The system configuration as described must be fully complied with and may not be changed. Tape width Tape thickness Adhesive consumption' 10cm 1 mm - 0.7 kg/m 15 em 1 mm - 1.0 kg/m 20 cm 1 mm -1.2 kg/m 15 cm 2mm -1.1 kg/m 20 cm 2mm -1.4 kg/m 25 cm 2mm -1.7 kg/m 30 cm 2mm -2.0 kg/m 'The consumption can vary dependent on site conditions (surface roughness, size of aggregate etc.) Substrate Quality Concrete, stone, mortar, renderings: Substrate must be clean, free from oil, grease, laitance or loose particles. Age of concrete 3-6 weeks depending on environmental conditions. Construction Steel37. V2A-Steel OWN 1.430U: Clean, free from oil, grease, rust and scale. Polyester, epoxy. ceramics. glass: Clean, free from oil and grease. 5 PDF created with pdfFactory Pro trial version www.pdffactory.com Sikedur-Combflexe SC system Sill EFTA01121243 Substrate Preparation Concrete, stone, mortar, rendering: Blastcleaning or equivalent mechanical means followed by thorough vacuum / dust removal. Construction Steel37: Blast°leaning or equivalent mechanical means followed by thorough vacuum / dust removal. Avoid dew point conditions for application. V2A-Steel OM 1.4301): Light grinding followed by thorough vacuum/dust removal. Avoid dew point conditions for application. Polyester, epoxy, ceramics, glass: Light roughening followed by thorough vacuum/dust removal. Do not apply to siliconised substrates. Avoid dew point conditions for application. Application Conditions / Limitations Substrate Temperature Sikadure-Combille, CF Adhesive and Sikadur.-31 CF: Type Slow: Type Rapid: Type Normal: from +25°C to +45°C from +5°C to +15°C from +10°C to +30°C Skadue-31 DW: From +10°C to +30°C Ambient Temperature Sikadue-Combillex e CF Adhesive and Skadurs-31 CF: Type Slow. Type Rapid: Type Normal: from +25°C to +45°C from +5°C to +15°C from +10°C to +30°C Skadut-31 DW: From +10°C to +30°C Substrate Moisture Content Cententitious substrates: Dry, max. mat damp. When applied to mat damp concrete, brush the adhesive well into substrate. Relative Air Humidity 85% max. (at +25°C) Dew Point Avoid condensation. The substrate must be at least 3°C above dew point. 6 PDF created with pdf Factory Pro trial version www.pdffactory.com Sikedur-Comtiflexe SC system Bill EFTA01121244 Application Instructions Mixing Mkadura-Combillei t CF Adhesive and Sthadur°-31 CF: Part A : B = 2 : 1 parts by weight or volume Siodue-31 OW: Part A : B = 3 : 1 parts by weight or volume Pre-batched units: Mix parts MB together for at least 2 minutes with a mixing spindle attached to a slow speed electric drill (max. 500 rpm) until the material becomes smooth in consistency and a uniform grey colour. Avoid aeration while mixing. Then, pour the whole mix into a clean container and stir again for approx. 1 more minute at low speed to keep air entrapment at a minimum. Mix only that quantity which can be used within its potlife. ■ 7 PDF created with pdfFactory Pro trial version www.pdffactory.com Sikedur-Combflexe SC system 711 EFTA01121245 Application Method I Tools Selection of tape size: Selection of the correct tape size (thickness and width) and of a suitable Sika° adhesive depends on the expected performance. If necessary. ask for technical advice. Tapes of 1 mm thickness are suitable for sealing of joints subject to light load only. Max. permissible permanent elongation: 1 mm tape: 10% of the non adhered tape width 2 mm tape: 25% of the non adhered tape width Note: For higher movement, place and fix tape in a loop into the joint. Application of tape: In case of dirt clean the surface of the Sikadur-Combiflee SG Tape with a dry or wet cloth. Use water and no solvent for cleaning. Check the Sikadur-Combillee SG Tape in respect of damages during storage and transport (e.g. heavy scratches) and remove critical parts if necessary. Note: No activation on site required In case of expansion joints or cracks > 1 mm the centre of the tape must not be "bonded" to the substrate. In this case, apply masking tape on top of the joint / crack and on both sides of the joint before applying the adhesive. Apply a suitable thoroughly mixed Sikadurt° adhesive on both sides of the joint / crack onto the prepared substrate, using a suitable trowel. If the concrete substrate is damp. force the adhesive well into the substrate. Layer thickness of adhesive should be 1 - 2 mm and the width on each side at least 40 mm. Before placing the Combiflex tape remove the masking tape on top of the expansion joint / crack. Apply the Combiflex tape within the open time of the adhesive. Press the tape firmly and without trapping air into the adhesive by using a suitable roller. The adhesive should be squeezed out on both sides of the tape by - 5 mm. In cases of expansion joints / cracks > 1 mm apply the Sikadur-Combiflex e SG-10/-20 M Tape with the red red masking tape facing upwards. In cases of high joint movement place the tape as a loop into the joint. For fixing overhead or in difficult configurations, the tape may be temporarily held in place with Skit Trocal Adhesive C-705. This adhesive, however may only be used in the tape centre but never on the areas to be bonded with Sikadur-Combiflex ®CF Adhesive, SikadurQs-31 CF or Sikadurt9-31 DW. 8 PDF created with pdfFactory Pro trial version www.pdffactory.com Sikedur-Combflexe SC system VII EFTA01121246 Let the base layer of the SikadurQ1-Combiflex t CF Adhesive. and Sikadurg-31 CF resp. Sikadurt9-31 DW lightly harden before the top layer is applied. Apply the adhesive at a thickness of - 1 mm on both sides of the joint / crack. producing a cover which tapers outwards to almost zero. This is followed by the removal of the red middle strip and the masking tape on both sides to ensure a neat and precise detail. The adhesive top layer may be smoothed with a brush using a diluted detergent. Allow adhesive to start curing first. Note: Do not use detergent if any coating is to be applied. When sealing construction joints or cracks of up to 1 mm width, the tape may be completely covered with Sikadurg-Combiflex e CF Adhesive. Sikadurw-31 CF or Sikadure-31 DW which also then provides mechanical protection. In these instances the Sikadur-Combiflex t SG Tape must be applied with the red middle strip facing downwards. Connection of Sikadur-Combiflex ® SG Tape: Tape ends are connected by hot air thermal welding The welding area must be prepared by roughing the surface by scotch brite or sand paper. Roughen the tapes only in the welding area otherwise the bonding effect can be affected. Overlaps have to be 40 - 50 mm. Connection of Stkadur-Combiflex ® SG Tape with Sucas PVC External Waterbar Type AR (only for construction joints): Sikadur-Combiflex ® SG Tape must overlap the Waterbar Type AR by at least a tape width. Clean the Sikadur-Combiflex g SG Tape with a dry cloth. Clean the waterbar with Sika® Colma-Cleaner and let it dry. Prime waterbar with Sika® Aktivator and allow to dry (min. 30 minutes, max. 24 hours). Bond the Combiflex tape and the Sika Waterbar together using Sikaffet-11 FC adhesive sealant at the thickness of 1 - 3 mm. Overcoat the contact areas by spatula with Sikaflexe-11 FC. Cleaning of Tools Clean all tools and application equipment with Sikaw Colma-Cleaner immediately after use. Hardened / cured material (adhesive) can only be mechanically removed. 9 PDF created with pdfFactory Pro trial version www.pdffactory.com Sikedur-Combflexe SC system 9/I EFTA01121247 Potlite Sikadur-Combitlex e CF Adhesive (6 kg) Temperature Type Normal Type Rapid +5°C - - 60 minutes +10°C - 125 minutes - 45 minutes +15°C - 95 minutes - 25 minutes +23°C - 50 minutes • +30°C - 25 minutes • Sikadure-31 CF (0.2 kg) Type Slow Type Normal Type Rapid +5°C - - - 60 minutes +10°C - - 145 minutes - 55 minutes +23°C - 135 minutes - 55 minutes - 40 minutes +30°C - - 35 minutes - +35°C - 70 minutes - +45°C - 45 minutes - - Temperature Sikadur•31 DW (0.2 kg) +23°C - 90 minutes If larger quantities are being mixed the temperature of the adhesive will increase due to the chemical reaction, resulting in a reduced potlife. Waiting Time / The Sikadure-Combiflex e CF Adhesive, Sikadue-31 CF and Sikadure-31 DW may Overcoating be overcoated with an epoxy coating. In this case do not smooth the adhesive with detergent. If the waiting time between application of adhesive and overcoating is to be longer than 2 days, the adhesive must be blinded to excess with quartz sand immediately after application. Notes on Application Limitations If joints are to be subjected to water pressure, the tape must be supported in the joint. Hard foam or joint sealant is recommended. For exposure to negative water pressure the Sikadur-Combiflex e SG Tape must be secured with a steel plate fixed on one side. Limit without support: For 5 mm joints at +20°C and max. 1 bar water head a tape of 2 mm thickness has to be installed. If a bituminous wearing layer is installed on top of Sikadur-Combiflex e SG System the temperature of the hot mix must not exceed +180°C up to max. 50mm thickness. Up to 10 mm thickness the temperature may be max. +220°C. If necessary apply in layers and allow to cool in between. The Sikadur-Combiflex e SG Tape must be protected from mechanical damage. The Sikadur-Combiflex e SG Tape can not be connected to the Sikaplan WT membranes by hot air welding. All technical data stated in this Product Data Sheet are based on laboratory tests. Value Base Actual measured data may vary due to circumstances beyond our control. Please note that as a result of specific local regulations the performance of this Local Restrictions product may vary from country to country. Please consult the local Product Data Sheet for the exact description of the application fields. For information and advice on the safe handling, storage and disposal of chemical Health and Safety products, users shall refer to the most recent Material Safety Data Sheet containing Information physical, ecological, toxicological and other safety-related data. 10 PDF created with pdf Factory Pro trial version www.pdffactory.com Sikedur-Combflexe SC system lei" EFTA01121248 Legal Notes The information, and, in particular, the recommendations relating to the application and end-use of Sika products, are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written recommendations, or from any other advice offered. The user of the product must test the product's suitability for the intended application and purpose. Sika reserves the right to change the properties of its products. The proprietary rights of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery. Users must always refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request. Sika Yapi IGmyasallari k$. fags Merkezi .90216444 74 52 MOW. Deri Org. San. Bel. 2. Yol J-7 Telefon .90 216 581 0600 III)1403.1 °Yds" 'al Parsel. Aychnle. &hank Meykii. Fake .90 216 581 0699 BUIFELParn 34957 Tote. Istanbul. T0rldye bilgifaitr sika rum zrzoLaikammli Owl/hem 11 PDF created with pdf Factory Pro trial version www.pdffactory.com Slkadur.COrnbilena SG system 11 't t EFTA01121249